System Manual
Table Of Contents
- Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
- Preface
- Product Overview
- General Description
- Cisco 860 Series ISRs
- Cisco 860VAE Series ISRs
- Cisco 880 Series ISRs
- Cisco 890 Series ISRs
- Hardware Features
- Installing the Router
- Connecting the Router
- Preparing to Connect the Router
- Connecting a PC, Server, or Workstation
- Connecting a Phone
- Connecting an External Ethernet Switch
- Connecting the V.92 modem Port
- Connecting a Terminal or PC to the Console Port
- Connecting a Modem to the Auxiliary Port
- Connecting the 3G Card
- Installing the 3G Adapter for Extended Cable/Antenna
- Connecting a Data BRI Port
- Connecting an FE Line to an FE WAN Port
- Connecting an GE Line to an GE WAN Port
- Connecting an xDSL Line
- Connecting Power over Ethernet
- Connecting the AC Adapter
- Connecting an FXS Line
- Connecting an FXO Line
- Connecting a Voice ISDN BRI Line
- Connecting a Small-form-factor Pluggable Module
- Verifying Connections
- Initial Configuration
- Technical Specifications
- Router Specifications
- Wireless Access Point
- FE and GE Port Pinouts
- Console and Auxiliary Port Connector Pinouts
- FXS and FXO Port Connector Pinouts
- VDSL2 Port Connector Pinouts
- ADSL2+ Port Connector Pinouts
- V.92 Port Connector Pinouts
- G.SHDSL Port Connector Pinouts
- Data BRI Port Connector Pinouts
- Voice ISDN BRI Interface Pin Numbers and Functions
- SFP Port Connector Pinouts
- Cable Specifications
4-2
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-07
Chapter 4 Initial Configuration
Cisco IOS CLI
To configure the initial router settings using the Cisco IOS CLI, follow these steps:
Step 1
Set up a console connection to your router. The following message is displayed:
...
router con0 is now available
Step 2
Press Return. The following message is displayed:
Cisco Configuration Professional Express (Cisco CP Express) is installed on this device.
This feature requires the one-time use of the username "username1"
with the password "password1." The default username and password have a privilege level of
15.
Please change these publicly known initial credentials using Cisco CP Express or the Cisco
IOS CLI.
Here are the Cisco IOS commands.
username <myuser> privilege 15 secret 0 <mypassword>
no username username1
Replace <myuser> and <mypassword> with the username and password you want to use.
For more information about Cisco CP please follow the instructions in the QUICK START
GUIDE for your router...
...
User Access Verification
Username:
Step 3
Enter the username username1, and press Return or Enter. The following prompt is displayed:
Password:
Step 4
Enter the password password1, and press Return or Enter. The following prompt is displayed:
Router#
A message is displayed that is similar to the first warning message. The message directs you to change
the username and password.
You are n o w in p r i vileged EX E C mod e .
Note
You must c h a nge th e u serna m e and p a s sword b e fo re y o u lo g off t h e router. Yo u c annot u s e the
username username1 or password password1 after you log off from this session.
Step 5
Enter configuration mode using the following commands.
Router#
Router#config t
Router(config)#
Router(config)#username username privilege 15 secret 0 password
Step 6
To change the username and password, enter the following at the prompt:
username username privilege 15 secret 0 password
The username and password are the username and password that you determine.
To continue using the Cisco IOS CLI for initial configuration, see the applicable configuration
procedures in
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers
Software Configuration Guide.