System Manual
Table Of Contents
- Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
- Preface
- Product Overview
- General Description
- Cisco 860 Series ISRs
- Cisco 860VAE Series ISRs
- Cisco 880 Series ISRs
- Cisco 890 Series ISRs
- Hardware Features
- Installing the Router
- Connecting the Router
- Preparing to Connect the Router
- Connecting a PC, Server, or Workstation
- Connecting a Phone
- Connecting an External Ethernet Switch
- Connecting the V.92 modem Port
- Connecting a Terminal or PC to the Console Port
- Connecting a Modem to the Auxiliary Port
- Connecting the 3G Card
- Installing the 3G Adapter for Extended Cable/Antenna
- Connecting a Data BRI Port
- Connecting an FE Line to an FE WAN Port
- Connecting an GE Line to an GE WAN Port
- Connecting an xDSL Line
- Connecting Power over Ethernet
- Connecting the AC Adapter
- Connecting an FXS Line
- Connecting an FXO Line
- Connecting a Voice ISDN BRI Line
- Connecting a Small-form-factor Pluggable Module
- Verifying Connections
- Initial Configuration
- Technical Specifications
- Router Specifications
- Wireless Access Point
- FE and GE Port Pinouts
- Console and Auxiliary Port Connector Pinouts
- FXS and FXO Port Connector Pinouts
- VDSL2 Port Connector Pinouts
- ADSL2+ Port Connector Pinouts
- V.92 Port Connector Pinouts
- G.SHDSL Port Connector Pinouts
- Data BRI Port Connector Pinouts
- Voice ISDN BRI Interface Pin Numbers and Functions
- SFP Port Connector Pinouts
- Cable Specifications
4-3
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-07
Chapter 4 Initial Configuration
Setup Command Facility
Note
Save your configuration changes regularly to avoid losing them during resets, power cycles, or
power outages. Use the copy
running-config startup-config command at the privileged EXEC
mode prompt (Router#) to save the configuration to NVRAM.
Step 7
Ver i f y t he i n i t i a l c o n f i gu r a t io n. S e e th e “Verifying the Initial Configuration” section on page 4-5.
Setup Command Facility
The setup command facility guides you through the configuration process by prompting you for the
specific information that is needed to configure your system. Use the setup command facility to
configure a hostname for the router, to set passwords, and to configure an interface for communication
with the management network.
To use the setup command facility, you must set up a console connection with the router and enter the
privileged EXEC mode.
Note
For instructions on how to set up a console connection, see the “Connecting a Terminal or PC to
the Console Port” section on page 3-7.
To configure the initial router settings by using the setup command facility, follow these steps:
Step 1
Set up a console connection to your router, and enter privileged EXEC mode. For instructions on how
to enter privileged EXEC mode, see
Step 1 through Step 4 in the “Cisco IOS CLI” section on page 4-1.
Step 2
In privileged EXEC mode, at the prompt, enter setup.
yourname# setup
The following message is displayed:
--- System Configuration Dialog ---
Continue with configuration dialog? [yes/no]:
You are n o w in the s e tup co m m a nd fac i l i t y.
The prompts in the setup command facility vary, depending on your router model, on the installed
interface modules, and on the software image. The following steps and the user entries (in bold) are
shown as examples only.
Note
If you make a mistake while using the setup command facility, you can exit and run the setup
command facility again. Press Ctrl-C, and enter the setup command at the privileged EXEC
mode prompt (Router#). For more information on using the setup command facility, see
“The
Setup Command” chapter in Cisco IOS Configuration Fundamentals Command Reference,
Release 12.2T.
Step 3
To proceed using the setup command facility, enter yes.
Continue with configuration dialog? [yes/no]: yes