User Guide
Table Of Contents
- Cisco Wireless ISR and HWIC Access Point Configuration Guide
- Contents
- Preface
- Overview
- Configuring Radio Settings
- Enabling the Radio Interface
- Roles in Radio Network
- Configuring Network or Fallback Role
- Universal Client Mode
- Configuring Universal Client Mode
- Configuring Radio Data Rates
- Configuring Radio Transmit Power
- Configuring Radio Channel Settings
- Enabling and Disabling World Mode
- Enabling and Disabling Short Radio Preambles
- Configuring Transmit and Receive Antennas
- Disabling and Enabling Access Point Extensions
- Configuring the Ethernet Encapsulation Transformation Method
- Enabling and Disabling Reliable Multicast to Workgroup Bridges
- Enabling and Disabling Public Secure Packet Forwarding
- Configuring Beacon Period and DTIM
- Configuring RTS Threshold and Retries
- Configuring Maximum Data Retries
- Configuring Fragmentation Threshold
- Enabling Short Slot Time for 802.11g Radios
- Performing a Carrier Busy Test
- Configuring Multiple SSIDs
- Configuring an Access Point as a Local Authenticator
- Understand Local Authentication
- Configure a Local Authenticator
- Guidelines for Local Authenticators
- Configuration Overview
- Configuring the Local Authenticator Access Point
- Configuring Other Access Points to Use the Local Authenticator
- Configuring EAP-FAST Settings
- Limiting the Local Authenticator to One Authentication Type
- Unblocking Locked Usernames
- Viewing Local Authenticator Statistics
- Using Debug Messages
- Configuring Encryption Types
- Configuring Authentication Types
- Configuring RADIUS Servers
- Configuring and Enabling RADIUS
- Understanding RADIUS
- RADIUS Operation
- Configuring RADIUS
- Default RADIUS Configuration
- Identifying the RADIUS Server Host
- Configuring RADIUS Login Authentication
- Defining AAA Server Groups
- Configuring RADIUS Authorization for User Privileged Access and Network Services
- Starting RADIUS Accounting
- Selecting the CSID Format
- Configuring Settings for All RADIUS Servers
- Configuring the Access Point to Use Vendor-Specific RADIUS Attributes
- Configuring the Access Point for Vendor-Proprietary RADIUS Server Communication
- Configuring WISPr RADIUS Attributes
- Displaying the RADIUS Configuration
- RADIUS Attributes Sent by the Access Point
- Configuring and Enabling RADIUS
- Configuring VLANs
- Configuring QoS
- Channel Settings
- Protocol Filters
- Supported MIBs
- Error and Event Messages
- Glossary
- Index
D-11
Cisco Wireless ISR and HWIC Access Point Configuration Guide
OL-6415-04
Appendix D Error and Event Messages
802.11 Subsystem Messages
Error Message DOT11-4-TKIP_MIC_FAILURE_REPORT: Received TKIP Michael MIC failure
report from the station [mac-address] on the packet (TSC=0x0) encrypted and
protected by [key] key
Explanation The access point received an EAPOL-key from the indicated station notifying the access
point that TKIP Michael MIC failed on a packet transmitted by this access point.
Recommended Action None.
Error Message DOT11-3-TKIP_MIC_FAILURE_REPEATED: Two TKIP Michael MIC failures were
detected within [number] seconds on [interface] interface. The interface will be
put on MIC failure hold state for next [number] seconds
Explanation Two TKIP Michael MIC failures were detected within the indicated time on the
indicated interface. Because this usually indicates an active attack on your network, the interface
will be put on hold for the indicated time. During this hold time, stations using TKIP ciphers are
disassociated and cannot reassociate until the hold time ends. At the end of the hold time, the
interface operates normally.
Recommended Action MIC failures usually indicate an active attack on your network. Search for and
remove potential rogue devices from your wireless LAN. If this is a false alarm and the interface
should not be on hold this long, use the countermeasure tkip hold-time command to adjust the hold
time.
Error Message SOAP-3-WGB_CLIENT_VLAN: Workgroup Bridge Ethernet client VLAN not
configured
Explanation No VLAN is configured for client devices attached to the workgroup bridge.
Recommended Action Configure a VLAN to accommodate client devices attached to the workgroup
bridge.
Error Message SOAP-3-ERROR: Reported on line [number] in file
[characters].[characters]
Explanation An internal error occurred on the indicated line number in the indicated filename in the
controller ASIC.
Recommended Action None
Error Message IF-4-MISPLACED_VLAN_TAG: Detected a misplaced VLAN tag on source
[interface]. Dropping packet
Explanation Received an 802.1Q VLAN tag which could not be parsed correctly. The received
packet was encapsulated or de encapsulated incorrectly.
Recommended Action