User Guide
Table Of Contents
- Cisco Wireless ISR and HWIC Access Point Configuration Guide
- Contents
- Preface
- Overview
- Configuring Radio Settings
- Enabling the Radio Interface
- Roles in Radio Network
- Configuring Network or Fallback Role
- Universal Client Mode
- Configuring Universal Client Mode
- Configuring Radio Data Rates
- Configuring Radio Transmit Power
- Configuring Radio Channel Settings
- Enabling and Disabling World Mode
- Enabling and Disabling Short Radio Preambles
- Configuring Transmit and Receive Antennas
- Disabling and Enabling Access Point Extensions
- Configuring the Ethernet Encapsulation Transformation Method
- Enabling and Disabling Reliable Multicast to Workgroup Bridges
- Enabling and Disabling Public Secure Packet Forwarding
- Configuring Beacon Period and DTIM
- Configuring RTS Threshold and Retries
- Configuring Maximum Data Retries
- Configuring Fragmentation Threshold
- Enabling Short Slot Time for 802.11g Radios
- Performing a Carrier Busy Test
- Configuring Multiple SSIDs
- Configuring an Access Point as a Local Authenticator
- Understand Local Authentication
- Configure a Local Authenticator
- Guidelines for Local Authenticators
- Configuration Overview
- Configuring the Local Authenticator Access Point
- Configuring Other Access Points to Use the Local Authenticator
- Configuring EAP-FAST Settings
- Limiting the Local Authenticator to One Authentication Type
- Unblocking Locked Usernames
- Viewing Local Authenticator Statistics
- Using Debug Messages
- Configuring Encryption Types
- Configuring Authentication Types
- Configuring RADIUS Servers
- Configuring and Enabling RADIUS
- Understanding RADIUS
- RADIUS Operation
- Configuring RADIUS
- Default RADIUS Configuration
- Identifying the RADIUS Server Host
- Configuring RADIUS Login Authentication
- Defining AAA Server Groups
- Configuring RADIUS Authorization for User Privileged Access and Network Services
- Starting RADIUS Accounting
- Selecting the CSID Format
- Configuring Settings for All RADIUS Servers
- Configuring the Access Point to Use Vendor-Specific RADIUS Attributes
- Configuring the Access Point for Vendor-Proprietary RADIUS Server Communication
- Configuring WISPr RADIUS Attributes
- Displaying the RADIUS Configuration
- RADIUS Attributes Sent by the Access Point
- Configuring and Enabling RADIUS
- Configuring VLANs
- Configuring QoS
- Channel Settings
- Protocol Filters
- Supported MIBs
- Error and Event Messages
- Glossary
- Index
2-22
Cisco Wireless ISR and HWIC Access Point Configuration Guide
OL-6415-04
Chapter 2 Configuring Radio Settings
Configuring Transmit and Receive Antennas
Short preambles are enabled by default. Use the preamble-short command to enable short preambles if
they are disabled.
Configuring Transmit and Receive Antennas
You c a n sel ec t th e an te nna th e wi rel es s dev ice use s to receive and transmit data. There are three options
for both the receive and the transmit antenna:
• Diversity—This default setting tells the wireless device to use the antenna that receives the best
signal. If the wireless device has two fixed (non-removable) antennas, you should use this setting
for both receive and transmit.
• Right—If the wireless device has removable antennas and you install a high-gain antenna on the
wireless device's right connector, you should use this setting for both receive and transmit. When
you look at the wireless device's back panel, the right antenna is on the right.
• Left—If the wireless device has removable antennas and you install a high-gain antenna on the
wireless device's left connector, you should use this setting for both receive and transmit. When you
look at the wireless device's back panel, the left antenna is on the left.
Beginning in privileged EXEC mode, follow these steps to select the antennas the wireless device uses
to receive and transmit data:
Step 3
no preamble-short Disable short preambles and enable long preambles.
Step 4
end Return to privileged EXEC mode.
Step 5
copy running-config startup-config (Optional) Save your entries in the configuration file.
Command Purpose
Command Purpose
Step 1
configure terminal Enter global configuration mode.
Step 2
interface dot11radio { 0 | 1 } Enter interface configuration mode for the radio interface. The
2.4-GHz radio is radio 0, and the 5-GHz radio is radio 1.
Step 3
antenna receive
{diversity | left | right}
Set the receive antenna to diversity, left, or right.
Note For best performance, leave the receive antenna setting
at the default setting, diversity.
Note The Cisco 850 series routers do not support diversity.
Step 4
antenna transmit
{diversity | left | right}
Set the transmit antenna to diversity, left, or right.
Note For best performance, leave the transmit antenna
setting at the default setting, diversity.
Step 5
end Return to privileged EXEC mode.
Step 6
copy running-config startup-config (Optional) Save your entries in the configuration file.