JetCell, Inc.
ViperCell Hardware Installation Beta Release 0.1 © Copyright 1999 JetCell Incorporated. All rights reserved. JetCell Confidential The information contained in this document is the property of JetCell, Inc. Except as specifically authorized in writing by JetCell, the holder of this document shall keep the information contained herein confidential and protect it from disclosure and dissemination to third parties in whole or in part and use same for evaluation purposes only.
-HW&HOO ,QF 7DEOH RI &RQWHQWV ViperCell Hardware Installation Installing ViperCell Hardware ............................................................. 1-1 Unpacking ViperCell .......................................................................... 1-1 Choosing Where to Mount ViperCell ................................................... 1-2 Mounting the Wall Bracket ................................................................. 1-2 Mounting the ViperCell to the Wall Bracket ........................
LL 9LS H U &H OO + D UG Z DU H , Q VW D OOD W LR Q ³ % H WD
-HW&HOO ,QF 9LSHU&HOO +DUGZDUH ,QVWDOODWLRQ A complete ViperNet Installation requires the installation of four major components: • The ViperCell combined GSM Radio and H.323 Endpoint hardware • The ViperWatch Operations, Administration, and Maintenance (OA&M) software • The ViperBase GSM-Enhanced H.323 Gatekeeper software • The V7M Interworking software This Installation and Commissioning (I&C) Guide describes how to install the ViperCell combined GSM Radio and H.323 Endpoint hardware.
• A GPS antenna assembly • A GPS connecting cable Report missing or damage items to JetCell, Inc. (E-Mail or Telephone number?) &KRRV LQJ : KHU H WR 0RXQW 9 L SHU&HO O Choosing where to install ViperCell is important: • Avoid placing ViperCell in direct sunlight or in locations of extreme heat or cold: ViperCell operates from -5C to +45C.
0RXQWLQJ WKH 9 LSHU&HOO WR WKH :DOO %U DFNHW Install the ViperCell into the wall bracket. 7R DW W DF K W K H 9 LS HU & HOO W R WK H ZD OO E U DF NH W 1 Position the ViperCell so that the LAN and power connectors are at the top of the unit. WARNING! Take care not to damage the flat antenna assemblies (not shown) attached to the front of the ViperCell unit. 2 Insert the mounting studs on the back of the ViperCell unit with the keyhole shaped holes on the wall bracket.
&RQQHFWLQJ 9 L SHU&HOO WR 3RZHU WARNING! Observe normal precautions for handling electronic equipment when attaching or removing power or lan connections to the ViperCell unit. The ViperCell combined GSM Radio and H.323 Endpoint receives power from a power transformer that accepts 110 to 220 VAC 50/60 Hz input and produces 12VDC at 5A regulated output. 7R F R Q Q H FW S RZH U W R WK H 9 LS H U& H OO 1 Insert the DC power connector into the power connection on the top of the ViperCell.
LS H U& H OO 6R IW ZD UH ,Q V WD OO $WWDFKLQJ WKH )DFHSO DWH After all other steps have been completed, install the decorative faceplate on the ViperCell unit. WARNING! Never use the decorative faceplate as a handle. Damage to the ViperCell unit will occur. Never use the plastic faceplate as a handle: it is not designed to support the weight of the ViperCell hardware. 7R DW W DF K W K H 9 LS HU & HOO ID F H S OD WH 1 Position the Faceplate in front of the ViperCell.
9LS H U& H OO 6R IW ZD UH ,Q V WD OO - 9LS H U& H OO + D UG ZD U H ,Q V WD OOD W LRQ ³ % HW D
