User's Manual
Table Of Contents
- Cisco WRP500 Administration Guide
- Contents
- 1
- WRP500 Features and Benefits
- Deployment Models
- Local Area Network Guidelines
- Special Requirements for Voice Deployments
- WRP500 Maintenance Operations
- Remote Provisioning
- Configure NAT Mapping
- Configure NAT Mapping with a Static IP Address
- Step 1 Log in as administrator.
- Step 2 Under the Voice menu, click SIP.
- Step 3 In the NAT Support Parameters section, enter the following settings:
- Step 4 Under the Voice menu, click Line 1 or Line 2 to choose the line interface that you want to modify.
- Step 5 In the NAT Settings section, enter the following settings:
- Step 6 Click Save Settings.
- Configure NAT Mapping with STUN
- Step 1 Log in as administrator.
- Step 2 Under the Voice menu, click SIP.
- Step 3 In the NAT Support Parameters section, enter the following settings:
- Step 4 Under the Voice menu, click Line 1 or Line 2 to choose the line interface that you want to modify.
- Step 5 In the NAT Settings section, enter the following settings:
- Step 6 Click Save Settings.
- Determine Whether the Router Uses Symmetric or Asymmetric NAT
- Step 1 Make sure you do not have firewall running on your computer that could block the syslog port (port 514 by default).
- Step 2 Log in as administrator.
- Step 3 To enable debugging, complete the following tasks:
- Step 4 To collect information about the type of NAT your router is using, complete the following tasks:
- Step 5 To enable SIP signaling, complete the following task:
- Step 6 Click Submit.
- Step 7 View the syslog messages to determine whether your network uses symmetric NAT. Look for a warning header in the REGISTER messages, such as Warning: 399 spa "Full Cone NAT Detected.”
- Configure NAT Mapping with a Static IP Address
- Firewalls and SIP
- Configure SIP Timer Values
- Analog Telephone Adapter Operations
- ATA Software Features
- Register to the Service Provider
- Step 1 Log in as administrator.
- Step 2 Under the Voice menu, click Line 1 or Line 2 to choose the line interface that you want to modify.
- Step 3 In the Proxy and Registration section, enter the Proxy.
- Step 4 In the Subscriber Information section, enter the User ID and Password.
- Step 5 Click Submit. The devices reboot.
- Step 6 To verify your progress, perform the following tasks:
- Manage Caller ID Service
- Optimize Fax Completion Rates
- Step 1 Ensure that you have enough bandwidth for the uplink and the downlink.
- Step 2 To optimize G.711 fallback fax completion rates, set the following on the Line tab of your ATA device:
- Step 3 If you are using a Cisco media gateway for PSTN termination, disable T.38 (fax relay) and enable fax using modem passthrough.
- Step 4 Enable T.38 fax on the WRP500 by configuring the following parameter on the Line tab for the FXS port to which the FAX machine is connected:
- Step 5 If you are using a Cisco media gateway use the following settings:
- Fax Troubleshooting
- Step 1 Verify that your fax machine is set to a speed between 7200 and 14400.
- Step 2 Send a test fax in a controlled environment between two ATAs.
- Step 3 Determine the success rate.
- Step 4 Monitor the network and record the following statistics:
- Step 5 If faxes fail consistently, capture a copy of the voice settings by selecting Save As > Web page, complete from the administration web server page. You can send this configuration file to Technical Support.
- Step 7 Identify the type of fax machine connected to the ATA device.
- Step 8 Contact technical support:
- Silence Suppression and Comfort Noise Generation
- Configure Dial Plans
- About Dial Plans
- Edit Dial Plans
- Enter the Line Interface Dial Plan
- Step 1 Start Internet Explorer, connect to the Configuration Utility, choose Voice > Admin Login. If prompted, enter the administrative login provided by the Service Provider. (The default username and password are both admin.)rovided by your Service...
- Step 2 Under the Voice menu, click Line 1 or Line 2, depending on the line interface that you want to configure.
- Step 3 Scroll down to the Dial Plan section.
- Step 4 Enter the digit sequences in the Dial Plan field. For more information, see “About Dial Plans,” on page 11.
- Step 5 Click Submit.
- Reset the Control Timers
- Step 1 Start Internet Explorer, connect to the Configuration Utility, choose Voice > Admin Login. If prompted, enter the administrative login provided by the Service Provider. (The default username and password are both admin.)rovided by your Service...
- Step 2 Under the Voice menu, click Regional.
- Step 3 Scroll down to the Control Timer Values section.
- Step 4 Enter the desired values in the Interdigit Long Timer field and the Interdigit Short Timer field. Refer to the definitions at the beginning of this section.
- Enter the Line Interface Dial Plan
- Secure Call Implementation
- Info page
- System page
- SIP page
- Regional page
- Line page
- Line Enable section
- Streaming Audio Server (SAS) section
- NAT Settings section
- Network Settings section
- SIP Settings section
- Proxy and Registration section
- Subscriber Information section
- Supplementary Service Subscription section
- Audio Configuration section
- Dial Plan section
- FXS Port Polarity Configuration section
- User page
- Setup
- Wireless Configuration
- Security
- Access Restrictions
- Applications and Gaming
- Administration
- Status
REVIEW DRAFT #1—CISCO CONFIDENTIAL
A-9
Cisco WRP500 Administration Guide
Appendix A Advanced Voice Fields
SIP page
Voice tab > SIP page >
Response Status Code Handling section
Reg Min Expires Minimum registration expiration time allowed from the proxy in the
Expires header or as a Contact header parameter. If the proxy
returns a value less than this setting, the minimum value is used.
The default is 1.
Reg Max Expires Maximum registration expiration time allowed from the proxy in
the Min-Expires header. If the value is larger than this setting, the
maximum value is used.
The default is 7200.
Reg Retry Intvl Interval to wait before the WRP500 retries registration after failing
during the last registration.
The default is 30.
Reg Retry Long Intvl When registration fails with a SIP response code that does not
match
Retry Reg RSC, the WRP500 waits for the specified length of time
before retrying. If this interval is 0, the WRP500 stops trying. This
value should be much larger than the Reg Retry Intvl value, which
should not be 0.
The default is 1200.
SIT1 RSC SIP response status code for the appropriate Special Information
Tone (SIT). For example, if you set the SIT1 RSC to 404, when the
user makes a call and a failure code of 404 is returned, the SIT1
tone is played. Reorder or Busy tone is played by default for all
unsuccessful response status code for SIT 1 RSC through SIT 4
RSC.
SIT2 RSC SIP response status code to INVITE on which to play the SIT2
Tone.
SIT3 RSC SIP response status code to INVITE on which to play the SIT3
Tone.
SIT4 RSC SIP response status code to INVITE on which to play the SIT4
Tone.
Try Backup RSC SIP response code that retries a backup server for the current
request.