User's Manual
Table Of Contents
- Cisco WRP500 Administration Guide
- Contents
- 1
- WRP500 Features and Benefits
- Deployment Models
- Local Area Network Guidelines
- Special Requirements for Voice Deployments
- WRP500 Maintenance Operations
- Remote Provisioning
- Configure NAT Mapping
- Configure NAT Mapping with a Static IP Address
- Step 1 Log in as administrator.
- Step 2 Under the Voice menu, click SIP.
- Step 3 In the NAT Support Parameters section, enter the following settings:
- Step 4 Under the Voice menu, click Line 1 or Line 2 to choose the line interface that you want to modify.
- Step 5 In the NAT Settings section, enter the following settings:
- Step 6 Click Save Settings.
- Configure NAT Mapping with STUN
- Step 1 Log in as administrator.
- Step 2 Under the Voice menu, click SIP.
- Step 3 In the NAT Support Parameters section, enter the following settings:
- Step 4 Under the Voice menu, click Line 1 or Line 2 to choose the line interface that you want to modify.
- Step 5 In the NAT Settings section, enter the following settings:
- Step 6 Click Save Settings.
- Determine Whether the Router Uses Symmetric or Asymmetric NAT
- Step 1 Make sure you do not have firewall running on your computer that could block the syslog port (port 514 by default).
- Step 2 Log in as administrator.
- Step 3 To enable debugging, complete the following tasks:
- Step 4 To collect information about the type of NAT your router is using, complete the following tasks:
- Step 5 To enable SIP signaling, complete the following task:
- Step 6 Click Submit.
- Step 7 View the syslog messages to determine whether your network uses symmetric NAT. Look for a warning header in the REGISTER messages, such as Warning: 399 spa "Full Cone NAT Detected.”
- Configure NAT Mapping with a Static IP Address
- Firewalls and SIP
- Configure SIP Timer Values
- Analog Telephone Adapter Operations
- ATA Software Features
- Register to the Service Provider
- Step 1 Log in as administrator.
- Step 2 Under the Voice menu, click Line 1 or Line 2 to choose the line interface that you want to modify.
- Step 3 In the Proxy and Registration section, enter the Proxy.
- Step 4 In the Subscriber Information section, enter the User ID and Password.
- Step 5 Click Submit. The devices reboot.
- Step 6 To verify your progress, perform the following tasks:
- Manage Caller ID Service
- Optimize Fax Completion Rates
- Step 1 Ensure that you have enough bandwidth for the uplink and the downlink.
- Step 2 To optimize G.711 fallback fax completion rates, set the following on the Line tab of your ATA device:
- Step 3 If you are using a Cisco media gateway for PSTN termination, disable T.38 (fax relay) and enable fax using modem passthrough.
- Step 4 Enable T.38 fax on the WRP500 by configuring the following parameter on the Line tab for the FXS port to which the FAX machine is connected:
- Step 5 If you are using a Cisco media gateway use the following settings:
- Fax Troubleshooting
- Step 1 Verify that your fax machine is set to a speed between 7200 and 14400.
- Step 2 Send a test fax in a controlled environment between two ATAs.
- Step 3 Determine the success rate.
- Step 4 Monitor the network and record the following statistics:
- Step 5 If faxes fail consistently, capture a copy of the voice settings by selecting Save As > Web page, complete from the administration web server page. You can send this configuration file to Technical Support.
- Step 7 Identify the type of fax machine connected to the ATA device.
- Step 8 Contact technical support:
- Silence Suppression and Comfort Noise Generation
- Configure Dial Plans
- About Dial Plans
- Edit Dial Plans
- Enter the Line Interface Dial Plan
- Step 1 Start Internet Explorer, connect to the Configuration Utility, choose Voice > Admin Login. If prompted, enter the administrative login provided by the Service Provider. (The default username and password are both admin.)rovided by your Service...
- Step 2 Under the Voice menu, click Line 1 or Line 2, depending on the line interface that you want to configure.
- Step 3 Scroll down to the Dial Plan section.
- Step 4 Enter the digit sequences in the Dial Plan field. For more information, see “About Dial Plans,” on page 11.
- Step 5 Click Submit.
- Reset the Control Timers
- Step 1 Start Internet Explorer, connect to the Configuration Utility, choose Voice > Admin Login. If prompted, enter the administrative login provided by the Service Provider. (The default username and password are both admin.)rovided by your Service...
- Step 2 Under the Voice menu, click Regional.
- Step 3 Scroll down to the Control Timer Values section.
- Step 4 Enter the desired values in the Interdigit Long Timer field and the Interdigit Short Timer field. Refer to the definitions at the beginning of this section.
- Enter the Line Interface Dial Plan
- Secure Call Implementation
- Info page
- System page
- SIP page
- Regional page
- Line page
- Line Enable section
- Streaming Audio Server (SAS) section
- NAT Settings section
- Network Settings section
- SIP Settings section
- Proxy and Registration section
- Subscriber Information section
- Supplementary Service Subscription section
- Audio Configuration section
- Dial Plan section
- FXS Port Polarity Configuration section
- User page
- Setup
- Wireless Configuration
- Security
- Access Restrictions
- Applications and Gaming
- Administration
- Status
REVIEW DRAFT #1—CISCO CONFIDENTIAL
A-14
Cisco WRP500 Administration Guide
Appendix A Advanced Voice Fields
Regional page
Voice tab > Regional page >
Call Progress Tones section
Dial Tone Prompts the user to enter a phone number. Reorder Tone is played
automatically when Dial Tone or any of its alternatives times out.
The default is 350@-19,440@-19;10(*/0/1+2).
Second Dial Tone Alternative to the Dial Tone when the user dials a three-way call.
The default is 420@-19,520@-19;10(*/0/1+2).
Outside Dial Tone Alternative to the Dial Tone. It prompts the user to enter an external
phone number, as opposed to an internal extension. It is triggered by
a, (comma) character encountered in the dial plan.
The default is 420@-19;10(*/0/1).
Prompt Tone Prompts the user to enter a call forwarding phone number.
The default is 520@-19,620@-19;10(*/0/1+2).
Busy Tone Played when a 486 RSC is received for an outbound call.
The default is 480@-19,620@-19;10(.5/.5/1+2).
Reorder Tone Played when an outbound call has failed or after the far end hangs
up during an established call. Reorder Tone is played automatically
when Dial Tone or any of its alternatives times out.
The default is 480@-19,620@-19;10(.25/.25/1+2).
Off Hook Warning
Tone
Played when the caller has not properly placed the handset on the
cradle. Off Hook Warning Tone is played when Reorder Tone times
out.
The default is 480@10,620@0;10(.125/.125/1+2).
Ring Back Tone Played during an outbound call when the far end is ringing.
The default is 440@-19,480@-19;*(2/4/1+2).
Ring Back 2 Tone Your WRP500 plays this ringback tone instead of Ring Back Tone if
the called party replies with a SIP 182 response without SDP to its
outbound INVITE request. The default value is the same as Ring
Back Tone, except the cadence is 1s on and 1s off.
The default is 440@-19,480@-19;*(1/1/1+2).
Confirm Tone Brief tone to notify the user that the last input value has been
accepted.
The default is 600@-16; 1(.25/.25/1).