User Manual
Table Of Contents
- 3G Wireless High-Speed WAN Interface Card for Cisco1800, 2800, and 3800 Series Routers
- Contents
- Prerequisites for Configuring the Wireless WAN HWIC
- Restrictions for the Wireless WAN HWIC
- Information About the Wireless WAN HWIC
- How to Configure the Wireless WAN HWIC
- Configuration Examples for the Wireless WAN HWIC
- Command Reference
- cellular cdma profile create
- cellular cdma profile activate
- cellular cdma otasp
- debug cellular messages all
- debug cellular messages async
- debug cellular messages data
- debug cellular messages dm
- debug cellular messages management
- debug cellular messages virt-con
- show cellular all
- show cellular connection
- show cellular connection personality
- show cellular connection statistics single-user
- show cellular connection statistics multi-user
- show cellular hardware
- show cellular network
- show cellular profile
- show cellular radio
- show cellular security
- show controllers cellular
- show interfaces cellular
- show run interface cellular
- test cellular cnm-process-enqueue
- test cellular modem-power-cycle
- test cellular modem-reset
- Supported Standards, MIBs, and RFCs
- Troubleshooting
- Glossary
BETA DRAFT —CISCO CONFIDENTIAL
3G Wireless High-Speed WAN Interface Card for Cisco 1800, 2800, and 3800 Series Routers
Command Reference
33
Cisco IOS Release TBD
show cellular connection statistics multi-user
To display the forward channle statistics for mulit-user traffic for the 1xEVDO-Rev A service, use the
show cellular connection statistics multi-user command in EXEC mode.
show cellular slot/wic_slot/port connection statistics multi-user
Syntax Description
Command Default There is no default for this command.
Command Modes EXEC
Command History
Usage Guidelines To clear the statictics, use the clear counters command.
Examples The following example shows output for code division multiple access (CDMA) for slot 0, WIC slot 0,
port 0:
c2800#sh cellular 0/0/0 connection statistics multi-user
DRC Info (Kbps) Format CRC Count Passed CRC Count Failed
=============== ============ ================ ================
DRC_03 ( 19.2) 128,4,256 0 0
DRC_03 ( 38.4) 256,4,256 0 0
DRC_03 ( 76.8) 512,4,256 0 0
DRC_03 ( 153.6) 1024,4,256 0 0
DRC_05 ( 307.2) 2048,4,128 0 0
DRC_08 ( 921.6) 3072,2,64 0 0
DRC_10 (1228.8) 4096,2,64 0 0
DRC_13 (1536.0) 5120,2,64 0 0
Total Bad Packets Received = 0
Total Packets Received = 0Packet Error Rate = 00.00 %
Throughput When Served = 0 kbps
Instantaneous Throughput = 0 kbps
Average Throughput (1sec) = 0 kbps
Termination Slot Count
DRC Info (Kbps) Format 1 2 3 4
=============== ========== ========== ========== ========== ==========
DRC_03 ( 19.2) 128,4,256 0 0 0 0
DRC_03 ( 38.4) 256,4,256 0 0 0 0
DRC_03 ( 76.8) 512,4,256 0 0 0 0
DRC_03 ( 153.6) 1024,4,256 0 0 0 0
DRC_05 ( 307.2) 2048,4,128 0 0 0 0
slot/wic_slot/port Numeric values that indicate the router slot, WAN interface card (WIC) slot,
and port.
Release Modification
This command was introduced.










