User Manual
Table Of Contents
- 3G Wireless High-Speed WAN Interface Card for Cisco1800, 2800, and 3800 Series Routers
- Contents
- Prerequisites for Configuring the Wireless WAN HWIC
- Restrictions for the Wireless WAN HWIC
- Information About the Wireless WAN HWIC
- How to Configure the Wireless WAN HWIC
- Configuration Examples for the Wireless WAN HWIC
- Command Reference
- cellular cdma profile create
- cellular cdma profile activate
- cellular cdma otasp
- debug cellular messages all
- debug cellular messages async
- debug cellular messages data
- debug cellular messages dm
- debug cellular messages management
- debug cellular messages virt-con
- show cellular all
- show cellular connection
- show cellular connection personality
- show cellular connection statistics single-user
- show cellular connection statistics multi-user
- show cellular hardware
- show cellular network
- show cellular profile
- show cellular radio
- show cellular security
- show controllers cellular
- show interfaces cellular
- show run interface cellular
- test cellular cnm-process-enqueue
- test cellular modem-power-cycle
- test cellular modem-reset
- Supported Standards, MIBs, and RFCs
- Troubleshooting
- Glossary
BETA DRAFT —CISCO CONFIDENTIAL
3G Wireless High-Speed WAN Interface Card for Cisco 1800, 2800, and 3800 Series Routers
Troubleshooting
58
Cisco IOS Release TBD
• Profile created; antenna disconnected
No profile created, Low RSSI
The following is a sample output from this command if the antenna is disconnected and a profile has not
been created. The errors in this case have been highlighted with >>>>>>>:
3825_GSM_3#sh cellular 0/3/0 all
Load for five secs: 0%/0%; one minute: 0%; five minutes: 1%
Time source is hardware calendar, 19:40:43.239 UTC Wed Nov 8 2006
Hardware Information
====================
Modem Firmware Version = H1_0_0_7MCAP G:/WS/
Modem Firmware built = 10/26/06
Hardware Version = 1.0
International Mobile Subscriber Identity (IMSI) = <specific sim number>
International Mobile Equipment Identity (IMEI) = <specific modem number>
Factory Serial Number (FSN) = X2819460388100D
Modem Status = Online
Current Modem Temperature = 38 deg C, State = Normal
Profile Information
====================
* - Default profile >>>>>>>> no profile here.
Data Connection Information
===========================
Profile 1, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 2, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 3, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 4, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 5, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 6, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 7, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 8, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 9, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 10, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 11, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 12, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 13, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 14, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 15, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 16, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Network Information