Final Draft - Cisco Conf idential Cisco 3200 Series Mobile Access Router Hardware Reference July 14, 2005 Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
Final Draft - Cisco Conf idential THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
CONTENTS Introduction to the Cisco 3200 Series Mobile Access Router Cards Audience and Scope ii Related Documentation ii Obtaining Documentation iv Cisco.
Contents CHAPTER 3 Serial Mobile Interface Card (SMIC) 3-1 SMIC Component Systems 3-2 Signals for the SMIC 3-3 Serial Cable Length 3-3 SMIC LED Signals 3-4 4-Port SMIC Rotary Switch Positions CHAPTER 4 Wireless Mobile Interface Card (WMIC) 3-4 4-1 WMIC Component Systems 4-1 Signals for the WMIC 4-2 10/100 Fast Ethernet Signals on the WMIC WMIC Multifunction Header Signals 4-4 LED Behavior 4-5 Antenna Connector 4-6 4-3 Key Features 4-6 2.4-GHz (802.11b/g) Features 4-6 4.
Introduction to the Cisco 3200 Series Mobile Access Router Cards The Cisco 3200 Series Mobile Access Routers include a combination of mobile interface cards.
Chapter 3, “Serial Mobile Interface Card (SMIC),” describes the Serial Mobile Interface Cards (SMICs) layout, ports, and buses. Chapter 4, “Wireless Mobile Interface Card (WMIC),” describes the Wireless Mobile Interface Cards (WMICs) layout, ports, and buses. Audience and Scope The audience for this document is the system administrator (SA), system integrator (SI), and system engineer (SE). They are experts, with networking industry training and experience.
• Cisco 3200 Series Mobile Access Router Hardware Reference1 (OL-5816)—descriptions of the Cisco MIC I/O cards found in Cisco 3200 Series routers. • Cisco 3200 Series Mobile Access Router Reference Sell Document1 (OL-3880)—An overview of the reference sell program and components for the Cisco 3200 Series router. • Regulatory Compliance and Safety Information for the Cisco 3200 Mobile Access Router (78-16930)—Regulatory compliance and safety information. 1.
Obtaining Documentation Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain technical assistance and other technical resources. These sections explain how to obtain technical information from Cisco Systems. Cisco.com You can access the Cisco website at this URL: http://www.cisco.com You can access international Cisco websites at this URL: http://www.cisco.com/public/countries_languages.
Documentation Feedback You can send comments about technical documentation to bug-doc@cisco.com. You can submit comments by using the response card (if present) behind the front cover of your document or by writing to the following address: Cisco Systems Attn: Customer Document Ordering 170 West Tasman Drive San Jose, CA 95134-9883 We appreciate your comments.
Obtaining Additional Publications and Information Information about Cisco products, technologies, and network solutions is available from various online and printed sources. • Cisco Marketplace provides a variety of Cisco books, reference guides, and logo merchandise. Visit Cisco Marketplace, the company store, at this URL: http://www.cisco.com/go/marketplace/ • The Cisco Product Catalog describes the networking products offered by Cisco Systems, as well as ordering and customer support services.
• Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering professionals involved in designing, developing, and operating public and private internets and intranets. You can access the Internet Protocol Journal at this URL: http://www.cisco.com/ipj • World-class networking training is available from Cisco. You can view current offerings at this URL: http://www.cisco.com/en/US/learning/index.
Processor Pentium 150 MHz or faster recommended Drives 4x CD-ROM drive Monitor Color monitor capable of 800 x 600 pixel resolution Software Adobe Acrobat Reader 4.0 or later Printing Documents from the CD To print a document: Step 1 Display the document in Acrobat. Step 2 Click the Printer icon on the Acrobat toolbar. The Windows Print Dialog box appears. Step 3 Select your default printer, and click OK.
Interactive examples use these conventions: • Terminal sessions and system displays are in screen font. • Information you enter is in boldface screen font. • Nonprinting characters, such as passwords or tabs, are in angle brackets (< >). Notes, cautions, and timesavers use these conventions and symbols: Tip Means the following will help you solve a problem. The tips information might not be troubleshooting or even an action, but could be useful information. Note Means reader take note.
Varoitus Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa ruumiinvammaan. Ennen kuin työskentelet minkään laitteiston parissa, ota selvää sähkökytkentöihin liittyvistä vaaroista ja tavanomaisista onnettomuuksien ehkäisykeinoista. (Tässä julkaisussa esiintyvien varoitusten käännökset löydät liitteestä "Translated Safety Warnings" (käännetyt turvallisuutta koskevat varoitukset).) Attention Ce symbole d’avertissement indique un danger.
Aviso Este símbolo de aviso indica perigo. Encontra-se numa situação que lhe poderá causar danos fisicos. Antes de começar a trabalhar com qualquer equipamento, familiarize-se com os perigos relacionados com circuitos eléctricos, e com quaisquer práticas comuns que possam prevenir possíveis acidentes. (Para ver as traduções dos avisos que constam desta publicação, consulte o apêndice “Translated Safety Warnings” - “Traduções dos Avisos de Segurança”).
Obtaining Technical Assistance For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, Cisco Technical Support provides 24-hour-a-day, award-winning technical assistance. The Cisco Technical Support Website on Cisco.com features extensive online support resources. In addition, Cisco Technical Assistance Center (TAC) engineers provide telephone support. If you do not hold a valid Cisco service contract, contact your reseller.
Submitting a Service Request Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3 and S4 service requests are those in which your network is minimally impaired or for which you require product information.) After you describe your situation, the TAC Service Request Tool provides recommended solutions. If your issue is not resolved using the recommended resources, your service request is assigned to a Cisco TAC engineer.
Severity 3 (S3)—Operational performance of your network is impaired, but most business operations remain functional. You and Cisco will commit resources during normal business hours to restore service to satisfactory levels. Severity 4 (S4)—You require information or assistance with Cisco product capabilities, installation, or configuration. There is little or no effect on your business operations.
C H A P T E R 1 Mobile Access Router Card (MARC) The Mobile Access Router Card (MARC) is one component of the Cisco 3200 Series Mobile Access Router. It includes the host processor, memory, and headers for the 10/100 Fast Ethernet, console, and auxiliary signals for the router. Additional components provide power and link interfaces to the MARC. For example, the 4-port Serial Mobile Interface Card provides up to 4 smart serial interfaces.
Chapter 1 Mobile Access Router Card (MARC) MARC Component Systems MARC Component Systems The industry-standard architecture (ISA) buses and peripheral component interconnect (PCI) buses on the Cisco 3200 Series Mobile Access Router cards provide power to the components on the cards. Both buses comply with the PC/104-Plus standard. The ISA bus allows PC/104-Plus ISA signals to pass through the card bus, but the Cisco cards do not use any of the signals.
Chapter 1 Mobile Access Router Card (MARC) MARC Component Systems The signals are delivered through the shared, 34-pin multifunction header and the 10-pin Ethernet header. LED signals and 5 V of power are also provided through the shared, 34-pin multifunction header. 10/100 Fast Ethernet Signals on the MARC There is one fixed 10/100 Fast Ethernet port on the MARC. A Cisco router identifies a 10/100 Fast Ethernet interface address by its slot number and port number, in the format slot/port.
Chapter 1 Mobile Access Router Card (MARC) MARC Component Systems Table 1-1 MARC Ethernet Header Pin Assignments (continued) Pin Signal Description 4 Unused Terminated 9 Unused Terminated 5 Reserved Do not use 10 Reserved Do not use The FastEthernet 0/0 port on the MARC is a 10/100 Fast Ethernet router port. The FastEthernet ports on the 4-port FESMIC and the 2-port FESMIC are 10/100 Fast Ethernet switch ports.
Chapter 1 Mobile Access Router Card (MARC) MARC Component Systems Table 1-2 MARC Multifunction Header Console Interface Pin Assignments (continued) Pin Signal Description 2 CON_TXD_OUT Transmit Data 19 GND Ground 3 GND Ground 20 CON_RXD_IN Receive Data 4 CON_DSR_IN Data Set Ready 21 CON_CTS_IN Clear To Send AUX Connections The AUX port is a serial asynchronous port that works at speeds of 1.2 Kbps, 2.4 Kbps, 4.8 Kbps, 9.6 Kbps, 19.2 Kbps, 38.4 Kbps, 57.6 Kbps, and 115.2 Kbps.
Chapter 1 Mobile Access Router Card (MARC) MARC Component Systems LED Connections Table 1-4 shows the MARC LEDs supported through the multifunction header that indicate system and LAN status. Table 1-4 MARC LEDs Multifunction Header Pin Assignments Pin Signal Description Function Indicates 10 LED_PWR Power–up status LED - (1) 27 +3.3V LED power supply LED + (1) Indicates the router operating status.
C H A P T E R 2 Fast Ethernet Switch Mobile Interface Card (FESMIC) The Fast Ethernet Switch Mobile Interface Card (FESMIC) is a mobile interface card (MIC) in a standard PC/104-Plus form factor. FESMICs are components of the Cisco 3200 Series Mobile Access Router. The 4-port FESMIC provides 4 sets of switched 10/100 Fast Ethernet signals. The 2-port FESMIC provides 2 sets of switched 10/100 Fast Ethernet signals.
Chapter 2 Fast Ethernet Switch Mobile Interface Card (FESMIC) Auto-Negotiation and Auto-MDI/MDIX Auto-Negotiation and Auto-MDI/MDIX All of the 10/100 Fast Ethernet interfaces support Ethernet auto-negotiation for the line transmission speed. Both sides of the connection are automatically set to either 10BASE-TX or 100BASE-TX. Auto-negotiation is widely used on most Ethernet interfaces, and it is the default mode.
Chapter 2 Fast Ethernet Switch Mobile Interface Card (FESMIC) FESMIC Component Systems FESMIC Component Systems The ISA buses and PCI buses on the Cisco 3200 Series Mobile Access Router cards provide power to the components on the cards. Both buses comply with the PC/104-Plus standard. The ISA bus allows PC/104-Plus ISA signals to pass through the card bus, but the Cisco cards do not use any of the signals. The PCI bus signals allow the Cisco cards to communicate.
Chapter 2 Fast Ethernet Switch Mobile Interface Card (FESMIC) FESMIC Component Systems Note 1 PCI bus 2 20-pin LED header 3 ISA bus 4 Rotary switch 5-8 E0–E3 10/100 Fast Ethernet headers The PC/104-Plus standard requires that the PCI bus and the ISA bus utilize keying features in the standard stacking headers to guarantee proper module installation. On the PCI bus, pin D30 is removed and the D30 opening is plugged.
Chapter 2 Fast Ethernet Switch Mobile Interface Card (FESMIC) FESMIC Component Systems The FastEthernet ports on the 4-port FESMIC and the 2-port FESMIC are 10/100 Fast Ethernet switch ports. The switch ports support all layer 2 features. The FastEthernet 0/0 port on the MARC is a 10/100 Fast Ethernet router port. The routing features supported on the MARC cannot be configured on the FESMIC ports. Figure 2-3 shows the 10-pin 10/100 Fast Ethernet header pin locations.
Chapter 2 Fast Ethernet Switch Mobile Interface Card (FESMIC) FESMIC Component Systems Table 2-3 FESMIC LED Header Pin Assignments Pin Signal Description 1 Port0 LINK+ Link Positive LED terminal Port 0 (power supply) 11 Port0 LINK- Link Negative LED terminal Port 0 2 Port0 ACT+ Active Positive LED terminal Port 0 Blinks when a packet is either (power supply) transmitted or received.
Chapter 2 Fast Ethernet Switch Mobile Interface Card (FESMIC) FESMIC Component Systems FESMIC Rotary Switch Positions The rotary switch position determines the IOS port number for the MIC. Table 2-4 shows the mapping of the switch positions to the IOS slot numbers. Table 2-4 Caution FESMIC Rotary Switch Positions Switch Position IOS Slot Number 0 1 1 2 2 3 3–7 Not supported The rotary switch positions must be unique and should not be assigned to more than one MIC.
Chapter 2 Fast Ethernet Switch Mobile Interface Card (FESMIC) FESMIC Component Systems Cisco 3200 Series Mobile Access Router Hardware Guide 2-8 OL-5816-04
C H A P T E R 3 Serial Mobile Interface Card (SMIC) The Serial Mobile Interface Card (SMIC) is one component of the Cisco 3200 Series Mobile Access Router. It provides the router up to 4 high–speed sets of serial signals in both data terminal equipment (DTE) and data circuit equipment (DCE) modes. Additional components provide power and link interfaces to the SMIC.
Chapter 3 Serial Mobile Interface Card (SMIC) SMIC Component Systems SMIC Component Systems Figure 3-1 shows the 2-port SMIC header and bus locations. Figure 3-1 2-port SMIC Header and Bus Locations 3 95227 1 2 4 1 PCI bus 2 60-pin multifunction header for Serial 0 and Serial 1 signals 3 ISA bus 4 Rotary switch Figure 3-2 shows the 4-port SMIC header and bus locations. Caution If you add non-Cisco cards that generates signals on the PCI bus, the router might shut down.
Chapter 3 Serial Mobile Interface Card (SMIC) SMIC Component Systems Signals for the SMIC The Cisco SSB Serial standard supports the following: • EIA/TIA-232, EIA/TIA-449, EIA-530, EIA-530A, X.21, and V.35 standards in both DTE or DCE modes. • Signals (SSB and LED) are provided through the 60-pin multifunction header(s). The position of the rotary switch determines the port assignments.
Chapter 3 Serial Mobile Interface Card (SMIC) SMIC Component Systems SMIC LED Signals Table 3-4 shows the LED signals that are supported on the SMIC, along with the corresponding functions. Serial 2 and Serial 3 apply to the 4-port SMIC only. Table 3-4 SMIC LED Functions LED Function SERIAL0 ACTIVITY Blinks once when a packet is either transmitted or received on Serial 0, and originates from Header 5. SERIAL0 LINK Indicates the status of Serial 0 and originates from Header 5.
Chapter 3 Serial Mobile Interface Card (SMIC) SMIC Component Systems Table 3-5 4-port SMIC Rotary Switch Positions and Serial Set Signal Assignments Rotary Switch Position MIC Slot Signal Assignments 2 3 Serial 3/0 Serial 3/1 Serial 3/2 Serial 3/3 3 4 Serial 4/0 Serial 4/1 Serial 4/2 Serial 4/3 Cisco 3200 Series Mobile Access Router Hardware Guide OL-5816-04 3-5
Chapter 3 Serial Mobile Interface Card (SMIC) SMIC Component Systems Cisco 3200 Series Mobile Access Router Hardware Guide 3-6 OL-5816-04
C H A P T E R 4 Wireless Mobile Interface Card (WMIC) The Wireless Mobile Interface Card (WMIC) is a mobile interface card (MIC) in a standard PC/104-Plus form factor. It is one component of the Cisco 3200 Series Mobile Access Routers and provides a 2.4-GHz (802.11b/g) or 4.9-GHz (US Only, Public Safety) wireless interface. The WMIC can be configured as a: • Wireless Access Point • Wireless Root Bridge • Wireless Non-root Bridge • Wireless Work Group Bridge.
Chapter 4 Wireless Mobile Interface Card (WMIC) WMIC Component Systems Figure 4-1 shows the WMIC header and bus locations.
Chapter 4 Wireless Mobile Interface Card (WMIC) WMIC Component Systems 10/100 Fast Ethernet Signals on the WMIC There is one set of fixed 10/100 Fast Ethernet signals on the WMIC. The 10/100 Fast Ethernet port signals are in compliance with IEEE 802.3.
Chapter 4 Wireless Mobile Interface Card (WMIC) WMIC Component Systems WMIC Multifunction Header Signals The multifunction header contains RS-232 console signals and three-color status LED signals. Figure 4-3 shows the 24-pin multifunction header that provides connections for the LEDs.
Chapter 4 Wireless Mobile Interface Card (WMIC) WMIC Component Systems LED Behavior During normal operations, the indicator signals on the wireless device have the following meanings. • The status indicator signals operational status. Steady green indicates that the wireless device is associated with at least one wireless client. Blinking green indicates that the wireless device is operating normally but is not associated with any wireless devices.
Chapter 4 Wireless Mobile Interface Card (WMIC) Key Features Table 4-3 Indicator Signals (continued) Message type Ethernet indicator Status indicator Radio indicator Meaning Configuration Reset – Amber – Resetting the configuration options to factory defaults. Failures Red Red Red Firmware failure; try disconnecting and reconnecting unit power. Blinking red – – Hardware failure. The wireless device must be replaced. – Red – Loading new firmware image.
Chapter 4 Wireless Mobile Interface Card (WMIC) Key Features Table 4-4 WMIC Key Features Security Cisco Wireless Security Suite including: Authentication: • 802.1X support including LEAP, PEAP, EAP-TLS, EAP-TTLS, and EAP-SIM to yield mutual authentication and dynamic, per-user, per-session WEP keys • MAC address and by standard 802.11 authentication mechanisms Encryption: Note • Support for static and dynamic IEEE 802.
Chapter 4 Wireless Mobile Interface Card (WMIC) Key Features Differences Between 2.4-GHz (802.11b/g) and 4.9-GHz (US Only, Public Safety) Radios Table 4-5 Differences between 2.4-GHz WMIC and 4.9-GHz WMIC Power 2.4-GHz (802.11b/g) 4.9-GHz (US Only, Public Safety) Maximum OFDM power level is 15dbm (30mw), but the power level might vary by country. Maximum OFDM power level is 17dbm (50mw). power client Command Supported Not supported. Concatenation Supported. Not supported.
Chapter 4 Wireless Mobile Interface Card (WMIC) Key Features 2.4-GHz (802.11b/g) Features The key features of the 2.4-GHz (802.11b/g) WMIC are listed below. Data Rates Supported 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, and 54 Mbps Network Standard IEEE 802.11b and IEEE 802.11g Frequency Band 2.400-GHz to 2.497-GHz Modulation BPSK QPSK CCK BPSK CCK2 QPSK 16 QAM 64 QAM Operating Channels North America: 11; ETSI: 13; Japan: 14 Receive Sensitivity 1 Mbps: -94 dBm 2 Mbps: -91 dBm 5.
Chapter 4 Wireless Mobile Interface Card (WMIC) Key Features 4.9-GHz (US Only, Public Safety) Features The key features of the 4.9-GHz (US Only, Public Safety) WMIC are listed below. Data Rates Supported 5-MHz channelization: 1.5, 2.25, 3, 4.5, 6, 9, 12, and 13.5 Mbps 10-MHz channelization: 3, 4.5, 6, 9, 12, 18, 24, and 27 Mbps 20-MHz channelization: 6, 9, 12, 18, 24, 36, 48, and 54 Mbps Network Standard Currently there is no IEEE 4.
Chapter 4 Wireless Mobile Interface Card (WMIC) Key Features Table 4-6 FCC 4.9 Operational Channels as per TIA TR-8 specification (continued) Operating Channel Channel Center 5-MHz Numbers Channel Spacing Channel Center 10-MHz Channel Spacing Channel Center 20-MHz Channel Spacing 30 4955.0 4955.0 4960.0 4960.0 4965.0 4965.0 4970.0 4970.0 4975.0 4975.0 4980.0 4980.0 35 4957.5 40 45 4962.5 50 55 4967.5 60 65 4972.5 70 75 4977.5 80 85 4982.5 90 4985.0 91 93 95 4987.
Chapter 4 Wireless Mobile Interface Card (WMIC) Power Requirements Modulation Table 4-7 shows the modulation. Table 4-7 Modulation Modulation 5 Mbps 10 Mbps 20 Mbps BPSK 1.5 Mbps and 2.25 Mbps 3 Mbps and 4.5 Mbps 6 Mbps and 9 Mbps QPSK 3 Mbps and 4.5 Mbps 6 Mbps and 9 Mbps 12 Mbps and 18 Mbps 16 QAM 6 Mbps and 9 Mbps 12 Mbps and 18 Mbps 24 Mbps and 27 Mbps 64 QAM 12 Mbps and 13.5 Mbps 24 Mbps and 27 Mbps 48 Mbps and 54 Mbps Receive Sensitivity Table 4-8 shows the receive sensitivity.
Chapter 4 Wireless Mobile Interface Card (WMIC) Related Documentation Related Documentation These documents provide detailed information regarding the configuration of the wireless card: • Cisco IOS Switching Services Configuration Guide. Click this link to browse to this document: http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fswtch_c/index.htm • Cisco Internetwork Design Guide. Click this link to browse to this document: http://www.cisco.
Chapter 4 Wireless Mobile Interface Card (WMIC) Related Documentation Cisco 3200 Series Mobile Access Router Hardware Guide 4-14 OL-5816-04
INDEX broadcast key rotation Numerics bus communication 10/100 Fast Ethernet auto-negotiation signals 1-2, 2-3, 3-1, 4-1 bus keying feature 1-2, 2-4, 3-1, 4-2 2-2 1-1, 2-1, 4-1 2.4-GHz (802.11b/g) WMIC 3rd-party devices C 4-1 1-2 4.9-MHz (public safety) WMIC cards 4-1 Cisco FESMIC 802.1D 2-1 Cisco MARC 802.1P 2-1 Cisco SMIC 802.1Q 2-1 Cisco WMIC CCITT V.
Index E H EIA/TIA-232 3-1 HDLC EIA/TIA-449 3-1 header keying EIA/TIA-530 3-1 header locations 3-1 1-2, 2-4, 3-1, 4-2 EIA/TIA-530A 3-1 Cisco FESMIC EIA/TIA-X.
Index K N key hashing non-Cisco cards 4-9 keying feature bus communication 1-2, 2-4, 3-1, 4-2 L 1-2, 2-3, 3-1, 4-1 P LEAP PC-104-Plus 4-9 LED PCI bus Cisco FESMIC Cisco MARC PEAP AUX signals status 2-2 1-4 console signals 4-5 radio traffic 4-9 ports 4-2 LED indicators Ethernet 1-1 per-VLAN spanning tree (PVST) 3-4 Cisco WMIC 1-2, 2-3, 4-1 PCI bus version 2-4 1-3 Cisco SMIC 1-2 1-4, 4-4 Fast Ethernet interface signals 4-5 serial interface signals 4-5 1-1, 2-1, 4-1
Index Cisco FESMIC 2-1 Cisco MARC V 1-1 Cisco SMIC VLAN routing 3-1 Cisco WMIC 2-2 4-1 RS232 transceiver 1-4 W WEP S 4-9 WMICs 4-1 serial asynchronous port baud rates signals 1-5 Z 1-4 zeroization 1-1, 3-1 1-1 serial interface Cisco MARC 1-1 Cisco SMIC 3-4 signals Cisco FESMIC Cisco MARC 2-4 1-3 Cisco SMIC 3-3 Cisco WMIC 4-2 Fast Ethernet 1-3, 2-1, 4-1 ISA bus 1-2, 2-3, 4-1 PCI bus 1-2, 2-3, 4-1 serial 1-3, 3-3 Spanning Tree Protocol (STP) status indicators switch
