Cisco 10005 ESR AC Power Supply Installation March 30, 2001 This installation note provides procedures for installing and replacing AC power supply modules in a Cisco 10005 edge services router (ESR).
Product Description Product Description The AC power supply (Figure 1) provides power conversion directly from the facility AC input power (100 to 240 VAC nominal) to the –48V VDC used internally by the system. Power is delivered to the power supply by the AC power cord. The AC power supply is provided with an IEC 320/C20 AC inlet, rated 16A/250V (20A in North America). Figure 1 AC Power Supply 100-240V 50/60 HZ 15-7A FAULT POWER 53616 CAUTION THIS UNIT SUPPLY HAS MOR POWER CORD.
Prerequisites and Preparation • Have access to the following documents during the installation: – Technology of Edge Aggregation: Cisco 10000 Series Edge Services Router (shipped with your router and available for viewing or download at Cisco.com) – Cisco 10005 ESR Hardware Installation Guide – Cisco 10000 Series ESR Troubleshooting Guide (an online document available for viewing or download at Cisco.
Prerequisites and Preparation Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. (To see translations of the warnings that appear in this publication, refer to the appendix “Translated Safety Warnings” in the installation guide that accompanied this device.
Prerequisites and Preparation Warnung Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu einer Körperverletzung führen könnte. Bevor Sie mit der Arbeit an irgendeinem Gerät beginnen, seien Sie sich der mit elektrischen Stromkreisen verbundenen Gefahren und der Standardpraktiken zur Vermeidung von Unfällen bewußt.
Prerequisites and Preparation ¡Advertencia! Varning! Este símbolo de aviso significa peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considerar los riesgos que entraña la corriente eléctrica y familiarizarse con los procedimientos estándar de prevención de accidentes. (Para ver traducciones de las advertencias que aparecen en esta publicación, consultar el apéndice titulado “Translated Safety Warnings,” en la guía de instalación que se acompaña con este dispositivo.
Adding or Replacing an AC Power Supply Adding or Replacing an AC Power Supply This section describes how to add or replace an AC power supply in a Cisco 10005 chassis. It contains these procedures: • Installing a Second AC Power Supply • Replacing an AC Power Supply • Troubleshooting the Installation Installing a Second AC Power Supply Warning Never install an AC power module and a DC power module in the same chassis.
Adding or Replacing an AC Power Supply Figure 2 RX RX RX RX RX TX TX TX TX TX Installing an AC Power Supply RX TX RX TX RX TX RX TX RX TX TX RX TX RX RX TX RX RX TX RX RX TX RX TX RX TX RX TX RX TX RX TX RX TX TX TX TX TX RX RX RX RX RX MINOR ALARM TX TX TX TX TX RX RX RX RX RX MAJOR ALARM EXT CLOCK A+ AB+ B- NO CO NC NO CO NC NO CO NC CRITICAL ALARM RX RX TX TX TX TX TX RX RX RX RX RX TX TX TX TX TX 60 VDC 1A MAX 100
Adding or Replacing an AC Power Supply Step 6 Snug up the strain relief device that secures the power cord to the power supply. To do this, tighten the screw underneath the connector (Figure 3). Figure 3 Tightening AC Power Cord Strain Relief 0V 2424 0V 0-01010 ZZ 0 0HH /6/6 5050 AA -7-7 1515 ION RR WE UTION PO WE CAUT CA EEPO ON ANON (2) THAN C AC OO(2) RETH UA TW NNOOIITTU MORE ECTTTW S MO NNEC HAS RE CONN RE FO DISCO K.K. UNIT HA BEFO OC IS UN OC RD..
Adding or Replacing an AC Power Supply Replacing an AC Power Supply Never install an AC power module and a DC power module in the same chassis. Warning Follow these steps to replace an AC power supply: Step 1 Put on an antistatic wrist or ankle strap. Attach the strap to the ESD grounding jack on the front of the chassis or to the bare metal surface of the chassis.
Adding or Replacing an AC Power Supply Figure 5 RX RX RX RX RX TX TX TX TX TX Step 3 Disconnect the power cable from the power supply that you are replacing. Step 4 Loosen the captive screws on the power supply and pull the power supply from the chassis using the handle on the faceplate. Step 5 Before you install the new power supply, make sure that its power switch is set to the standby position (see Figure 4).
Adding or Replacing an AC Power Supply Snug up the strain relief device that secures the power cord to the power supply. To do this, tighten the screw underneath the connector (Figure 6). Tightening AC Power Cord Strain Relief ION RR WE UTION PO WE CAUT CA EEPO ON ANON (2) THAN C AC OO(2) RETH UA TW NNOOIITTU MORE ECTTTW S MO NNEC HAS RE CONN RE FO DISCO K.K. UNIT HA BEFO OC IS UN OC RD..
FCC Class B Compliance Troubleshooting the Installation Table 1 contains troubleshooting tips for an AC-powered Cisco 10005 ESR. Table 1 Troubleshooting AC-Powered Systems Symptom Steps to Take System fails to power on Check that: Power supply Fault LED is on (yellow) • All power cords are properly connected to the Cisco 10005 and at the power connection end. • The power switches are in the | (On) position. • The Power LED is on (green).
Related Documentation You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures: • Turn the television or radio antenna until the interference stops. • Move the equipment to one side or the other of the television or radio.
Obtaining Documentation • Cisco 10000 Series ESR Useful Links • Cisco 10000 technical reference documents Hardware Documents for Cisco 10008 Routers • Cisco 10008 ESR Hardware Installation Guide • Cisco 10008 ESR AC Power Entry Module Installation • Cisco 10008 ESR DC Power Entry Module Installation • Cisco 10008 ESR Blower Module Installation Hardware Documents for Cisco 10005 Routers • Cisco 10005 ESR Hardware Installation Guide • Cisco 10005 ESR Hardware Overview and Maintenance Guide (on
Obtaining Documentation Documentation CD-ROM Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product. The Documentation CD-ROM is updated monthly and may be more current than printed documentation. The CD-ROM package is available as a single unit or through an annual subscription.
Obtaining Technical Assistance Obtaining Technical Assistance Cisco provides Cisco.com as a starting point for all technical assistance. Customers and partners can obtain documentation, troubleshooting tips, and sample configurations from online tools. For Cisco.com registered users, additional troubleshooting tools are available from the TAC website. Cisco.com Cisco.
Obtaining Technical Assistance Contacting TAC by Using the Cisco TAC Website If you have a priority level 3 (P3) or priority level 4 (P4) problem, contact TAC by going to the TAC website: http://www.cisco.com/tac P3 and P4 level problems are defined as follows: • P3—Your network performance is degraded. Network functionality is noticeably impaired, but most business operations continue.
Obtaining Technical Assistance Cisco 10005 ESR AC Power Supply Installation 78-12652-01 19
Obtaining Technical Assistance Use this document in conjunction with the documents listed in the “Related Documentation” section.