Quick Start Guide Cisco 10008 Router 1 Documentation and Resources 2 Preparing for Installation 3 Installing the Router 4 Connecting Power 5 Connecting Cables 6 Powering On the System 7 Configuring the Cisco 10008 Router at Startup 8 Formatting Flash Disks and Flash Cards 9 Managing the File Systems 10 Troubleshooting Installation Problems
1 Documentation and Resources This section contains information to help you prepare for installing the Cisco 10008 router. It contains a list of online documentation and resources. Document Version History This is the first version of the document with an online part number. The document version history beginning with this online part number is in Table 1.
You can access the Cisco website at this URL: http://www.cisco.com You can access international Cisco websites at this URL: http://www.cisco.com/public/countries_languages.shtml Product Documentation DVD Cisco documentation and additional literature are available in the Product Documentation DVD package, which may have shipped with your product. The Product Documentation DVD is updated regularly and may be more current than printed documentation.
Cisco Product Security Overview Cisco provides a free online Security Vulnerability Policy portal at this URL: http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html From this site, you can perform these tasks: • Report security vulnerabilities in Cisco products. • Obtain assistance with security incidents that involve Cisco products. • Register to receive security information from Cisco.
Cisco Technical Support & Documentation Website The Cisco Technical Support & Documentation website provides online documents and tools for troubleshooting and resolving technical issues with Cisco products and technologies. The website is available 24 hours a day, at this URL: http://www.cisco.com/techsupport Access to all tools on the Cisco Technical Support & Documentation website requires a Cisco.com user ID and password.
Obtaining Additional Publications and Information Information about Cisco products, technologies, and network solutions is available from various online and printed sources. • Cisco Marketplace provides a variety of Cisco books, reference guides, documentation, and logo merchandise. Visit Cisco Marketplace, the company store, at this URL: http://www.cisco.com/go/marketplace/ • Cisco Press publishes a wide range of general networking, training and certification titles.
2 Preparing for Installation This section guides you through the process of preparing for your router installation. Warning Only trained and qualified personnel should be allowed to install or replace this equipment.
3 Installing the Router The Cisco 10008 router can be rack-mounted in a 19-inch rack with either a flush-mount or center-mount configuration, or in a 23-inch rack in a center-mount configuration. Use the rack-mounting kit provided with your system. If you choose to install the Cisco 10008 router on a workbench or tabletop: Step 1 Ensure that you have a minimum of 3 inches (7.
Lifting the Chassis Use the following procedure to rack-mount the Cisco 10008 chassis: Figure 1 Lifting the Chassis FANS FAN OK FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replaceme tray, system in under two nt must shutdown minutes will occur.
Rack-Mounting the Router in a 19-Inch 4-Post Rack Use the following procedure to rack-mount the Cisco 10008 chassis in a 19-inch 4-post rack: Figure 2 Attaching the Chassis to a 19-Inch 4-Post Rack FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replacem tray, system in under two ent must shutdown minu will occutes or r.
Rack-Mounting the Router in a 19-Inch 2-Post Rack Use the following procedure to rack-mount the Cisco 10008 chassis in a 19-inch 2-post rack: Figure 3 Attaching the Mounting Brackets to the Chassis FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replacem tray, system in under two ent must shutdown minu will occutes or r.
Figure 4 Attaching the Chassis to a 19-Inch 2-Post Rack FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replacem tray, system in under two ent must shutdown minu will occutes or r.
Rack-Mounting the Router in a 23-Inch 2-Post Rack Use the following procedure to rack-mount the Cisco 10008 chassis in a 23-inch 2-Post rack: Figure 5 Attaching Mounting Brackets to the Chassis FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replaceme tray, system in under two nt must shutdown minu will occutes or r.
Figure 6 Attaching 23-Inch 2-Post Rack Bracket Adapters FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replacem tray, system in under two ent must shutdown minu will occutes or r.
Figure 7 Attaching the Chassis to a 23-Inch 2-Post Rack FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replacem tray, system in under two ent must shutdown minu will occutes or r.
Attaching the Cable-Management Bracket Use the following procedure to attach the cable-management bracket to the Cisco 10008 chassis: Figure 8 Attaching the Cable-Management Bracket FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replaceme tray, system in under two nt must shutdown minut will occures or .
Attaching the Grounding Lug Use the procedure in this section to attach the grounding lug: Before attaching the grounding lug, make sure: • The ejector levers are in the closed position. • The chassis mounting screws are tight. • The Performance Routing Engine (PRE) and line card captive screws are tight. • The power switches on the DC or AC Power Entry Module (PEM) are set to the Off position. Figure 9 Attaching Grounding Wire to Grounding Lug 30020 0.75 in.
Connecting the Grounding Lug to the Chassis 132825 Figure 10 1 1 Threaded grounding holes (2) Warning Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 93 Step 3 Attach the grounding lug firmly to threaded holes at the bottom rear of the chassis using two M5 screws.
4 Connecting Power Use this section for information about connecting power to the Cisco 10008 router. • If you are connecting DC power to the system, go to the “Connecting DC Power to the Cisco 10008 Router” section on page 19. • If you are connecting AC power to the system, go to the “Connecting AC Power to the Cisco 10008 Router” section on page 23 Connecting DC Power to the Cisco 10008 Router This section describes how to connect the Cisco 10008 router to a –48 VDC power source.
Be sure you have connected the chassis to an earth ground as instructed in the “Attaching the Grounding Lug” section on page 17, and then use the following procedure to connect the chassis to a DC power source: Figure 11 Setting DC PEM Switches to the Off Position FANS OK FAN FAILUR E MULTIFAN FAILUR E When hot CAUTION removal swapping this fan be done and replacement tray, must system in under two shutdo wn will minutes or occur.
Removing the Safety Cover 30023 Figure 12 Step 2 Loosen the captive screw on the rear safety cover and tilt the cover back to lift it up and out from the chassis. Figure 13 Stripping Insulation 14747 10 mm max Step 3 Using a wire-stripping tool, strip not more than 0.4 inches (10 mm) of insulation off the ends of the DC power leads.
Figure 14 DC Power Connections RTN (+ ) – 48/– 60 V DC terminal block A DC terminal block B 30024 RTN (+ ) – 48/– 60 V Step 4 Connect the DC power lead from the first external power source to the DC terminal block A labeled –48V. Step 5 Connect the return wire (RTN) to terminal block A labeled RTN (+). • If you have redundant DC power, continue with Step 6. • If you do not have redundant DC power, go to Step 8.
Securing DC Power Cables to the Chassis 30025 Figure 15 Step 8 Secure the power cabling to the chassis by feeding a tie wrap through the slot on the safety cover and binding the cables. Step 9 Replace the rear safety cover, making sure that the power wires exit through the holes on the side of the safety cover. This completes the installation of the Cisco 10008 chassis in the rack. Go to the “Connecting Cables” section on page 26.
Be sure you have connected the chassis to an earth ground as instructed in the “Attaching the Grounding Lug” section on page 17, and then use the following procedure to connect AC power to the PEM: Figure 16 Setting AC PEM Switches to the Off Position FANS OK FAN FAILUR E MULTI FAN FAILUR E When hot CAUTION removal swapping this fan be done and replacement tray, must system in under two shutdo wn will minutes or occur.
Figure 17 AC Power Cord Connectors in Strain-Relief Devices 1 FANS OK FAN FAILUR E MULTI FAN FAILUR E When hot CAUTION removal swapping this fan be done and replacement tray, must system in under two shutdo wn will minutes or occur.
5 Connecting Cables This section provides information about connecting cables to the Cisco 10008 router. Connecting Alarm Indicators The Cisco 10008 router provides relay contacts for optional (customer-supplied) audible or visual alarm indicators. Relay contacts are provided for three levels of severity: • Minor—An informational alarm that does not affect system operation. • Major—An alarm condition that affects system operation and should be investigated as soon as possible.
Removing the Safety Cover 30023 Figure 19 Step 2 Remove the safety cover by lifting it up and out from the chassis. Figure 20 Stripping Insulation 14747 10 mm max Step 3 Using a wire-stripping tool, strip not more than 0.4 inches (10 mm) of insulation off the ends of the alarm indicator wire.
Figure 21 Alarm Indicator Terminal Block Connections ALARMS 50VA SELV max NC COM MINOR NO NC COM MAJOR NO 32694 NC COM CRITICAL NO Step 4 Connect one set of alarm indicator wires to the alarm terminal block as follows: a. Connect one lead to the common (COM) terminal. b. Connect the other lead to the normally closed (NC) or normally open (NO) terminal. Caution Step 5 28 Figure 21 shows the wiring configuration for normally open (NO) alarm relays.
Alarm Indicator Wires Exiting the Safety Cover 32693 Figure 22 Step 6 Secure the power cabling to the chassis by feeding a tie wrap through the slot in the safety cover and binding the wires. Step 7 Replace the rear safety cover, making sure that the alarm indicator wires exit through the hole on the side of the safety cover. Connecting a Video Terminal to the PRE Console Port The Cisco 10008 router PRE has an asynchronous serial (EIA/TIA-232) RJ-45 console port labeled CON on its front panel.
Use the following procedure to connect a video terminal to the console port on a PRE: Figure 23 Console Port Connection on the PRE CISCO 10000 C O N S O LE AU X LI N K 30027 1 OT SL 0 OT SL E TH E R N LI E N T K Step 1 Connect one end of the RJ-45 crossover cable to the serial RJ-45 port (CONSOLE) on the PRE. Step 2 Run the cable up and through the cable-management bracket and connect the other end of the RJ-45 crossover cable to the RJ-45 adapter (Figure 24).
Connecting Network Management and Signal System Cables The Cisco 10008 router has connections to both the internal Ethernet management network and the external data network: • The internal Ethernet management network connections are made through an Ethernet port on the front panel of the PRE. • The external data network connections are made through DS3 connectors on the router’s backplane, and through the front panel ports on several types of line cards.
Follow these steps to connect the PRE to a 10BASE-T Ethernet LAN: Figure 25 Connecting the 10BASE-T Cable to the Ethernet Port CISCO 10000 C O AU LI N S O LE X N E K TH N E K R N E T 30036 1 OT SL 0 OT SL LI Step 1 Connect one end of the Ethernet cable to the RJ-45 port on the primary PRE, labeled ETHERNET. Step 2 Run the cable up and through the cable-management bracket and connect the other end of the Ethernet cable to any unoccupied port on the Ethernet hub.
The RJ-45 port on the PRE is configurable for 100-Mbps full-duplex or half-duplex operation (half-duplex is the default) and supports IEEE 802.3, Ethernet, and IEEE 802.3u interfaces compliant with 100BASE-T specifications.
Auxiliary Modem Connection This asynchronous EIA/TIA-232 serial port is used to connect a modem to the PRE for remote administrative access. Use the following procedure to connect the Cisco 10008 router to a modem. Figure 27 Connecting the Modem Cable to the Auxiliary Port CISCO 10000 C O AU LI E N O LE X N K TH N E K R N E T 33357 1 OT SL 0 OT SL LI S Step 1 Connect one end of the modem cable to the RJ-45 port on the primary PRE, labeled AUX.
6 Powering On the System When all of the interfaces are connected, perform a visual check of all connections, and then check that: • The ejector levers on each line card are in the locked position. • All top and bottom line card captive screws are tight. • All network interface cables are connected to the line cards. • The console terminal is turned on. • A Flash memory card is installed in the PRE.
7 Configuring the Cisco 10008 Router at Startup This section explains how to create a basic running configuration for your Cisco 10008 router using the Cisco 10008 setup facility or the Cisco IOS command-line interface (CLI). For information on modifying the configuration after you create it, see the online Cisco 10000 Series Routers Documentation Roadmap document for links to a complete listing of documents that will help you configure the Cisco 10008 router.
Tip Basic configuration setup is often used as a quick way to achieve network connectivity, allowing you to retrieve a configuration file from a TFTP server. Using the System Configuration Dialog Use the System Configuration Dialog to help you perform a basic configuration. Proceed through the dialog by answering questions and then pressing the Enter key. In most cases, you can get additional information by entering a question mark (?).
After you respond to the SNMP questions, the setup script lists the interfaces., for example: Interface IP-Address OK? Method Status Protocol Ethernet0/0/0 unassigned YES unset up up FastEthernet0/0/0 unassigned NO unset up up Interfaces that are not okay (OK? = NO) do not have a valid configuration. Step 10 To achieve network connectivity, enter the interface for the Fast Ethernet interface.
Step 17 After you complete the configuration dialog, enter global configuration mode and enable IP routing by entering the ip routing command: Router(config)# ip routing Basic Configuration in Global Configuration Mode The following command sequence allows you to perform a configuration similar to that generated by the setup command: Router> configure terminal Router(config) # hostname c10008 Router(config) # enable secret my_router Router(config) # enable password my_rtr Router(config) # snmp-server commu
8 Formatting Flash Disks and Flash Cards The Flash disk or Flash card that shipped with your router contains the default Cisco IOS image for booting your router. This section explains how to format an ATA Flash disk, modify its contents, or resolve a problem with the Flash card. Caution The formatting procedure erases all information on Flash memory disks or Flash cards. ATA Flash disks and Flash cards use similar commands.
9 Managing the File Systems This section describes the file systems used on the Cisco 10008 router and provides procedures for performing basic file system tasks. File Systems The Cisco 10008 router includes the file systems described in the following table. Table 3 File Systems File System CLI Name Description Bootflash Secondary bootflash bootflash: sec-bootflash: Stores image and dump files.
Managing Configuration Files Larger than NVRAM To maintain a configuration file that exceeds the size of NVRAM (512 KB), you must compress or relocate the configuration file. This section provides an example of each approach. For more information, refer to the Cisco IOS Configuration Fundamentals Configuration Guide. Compressing the Configuration File Use the service compress-config global configuration command to compress the configuration file for storage in NVRAM.
Step 5 Exit global configuration mode. Router(config)# end Step 6 When you finish changing the running configuration, save the new configuration. Router# copy running-config startup-config As a result of this procedure, when you reboot the Cisco 10008 router, it loads the configuration file that resides on Flash disk 0.
10 Troubleshooting Installation Problems This section contains general troubleshooting information to help you solve problems you might encounter during the installation of the system. For any problems not covered in this section and for more detailed troubleshooting information, see the Cisco 10000 Series Internet Router Troubleshooting Guide. General Troubleshooting Tips All Cisco 10008 field-replaceable units (FRUs) are hot-swappable.
Troubleshooting Ethernet Connections If an Ethernet connection to your Cisco 10008 router fails to work properly, and the corresponding LINK LED is not on, check for the following problems: • Visually check that an Ethernet cable is connected to the correct Ethernet port on the PRE, and that the other end of the cable is connected to an Ethernet hub that is powered on and functioning properly. • Check to see if you are using the correct type of cable.
Troubleshooting the Console Port Serial Connection If the terminal connected to the Cisco 10008 console port appears frozen or fails to work properly, check for the following problems: • Check the console cable and make sure it is properly connected to the correct console port on the PRE, and to your equipment at the other end. • Verify that you are using the proper type of cable and adapter. • To be sure the cable is not defective or broken, replace the cable with another high-quality cable if possible.
Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 European Headquarters Cisco Systems International BV Haarlerbergpark Haarlerbergweg 13-19 1101 CH Amsterdam The Netherlands www-europe.cisco.com Tel: 31 0 20 357 1000 Fax: 31 0 20 357 1100 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA www.cisco.
