Quick Start Guide CISCO INTELLIGENCE ENGINE 2100 SERIES MOUNTING, CABLING, AND SETUP Cisco Intelligence Engine 2100 Series MODE DRIVE 0 DRIVE 1 Console Hub MODE MODE MODE MODE MODE 53002 MODE MODE MODE MODE Routers Routers 1 TAKE OUT WHAT YOU NEED 2 RACK MOUNT THE HARDWARE 3 CONNECT CABLES 4 RUN THE SETUP PROGRAM Routers
Take Out What You Need This guide explains how to mount, cable, and set up your Cisco Intelligence Engine 2100 Series (IE2100 Series).
Take Out What You Need (continued) Cables and Power Cord 1 yellow Ethernet 10BaseT cable (to connect to a 10BaseT hub) 1 flat, light-blue console cable with 1 RJ-45 adapter, labeled TERMINAL (RJ-45-to-DB-9) 1 black power cord Rack-Mount Kit 2 L mounting brackets (left and right) 2 4 M4 Phillips countersunk-head screws 4 12-24 x 3/4-inch Phillips binder-head screws 4 10-32 x 3/4-inch slotted binder-head screws 1 8-32 x 1/2-inch black Phillips binder-head screw Desktop-Mount Kit 4 Desktop mounting self-a
Rack Mount the Hardware LINK 100Mbp s LINK MODE CONS ETHERN ET 0 100Mbp s DRIVE 0 ETHERN ET 1 DRIVE 1 Intelligen e 2100 Series 49336 ce Engin Phillips machine screws Installing Rack Mount Hardware To install the IE2100 Series in a rack: Step 1 will fit. This section describes how to install the IE2100 Series in a standard 19-inch equipment rack.
Connect Cables Cisco Intelligence Engine 2100 Series MODE DRIVE 0 DRIVE 1 Console Hub MODE MODE MODE MODE MODE 53002 MODE MODE MODE MODE Routers Connecting the Ethernet and Console Cables Use the console cable in the accessory kit to connect the IE2100 Series console port (CONS) to a console or Cisco Intelligence Engine 2100 Series LINK 100Mbp s LINK 100Mbp MODE CONS ETHER NET 0 ETHER s DRIVE NET 1 0 DRIVE 1 Intelligenc e Engin e 2100 Series Cons Port (RJ-45) computer that is r
Connect Cables (continued) Power receptacle AC power connector Connect the Power Cable Step 1 Verify that the Power switch is set to OFF. Step 2 Connect the black power cable to the power receptacle on the rear panel of the IE2100 Series. Step 3 Connect the other end of the power cable to an AC power source. Step 4 Set the power switch to ON. Step 5 Verify that the IE2100 Series is operational.
Run the Setup Program This section explains how to run the setup program Primary DNS nameserver IP address IP address of DNS server that to configure the system. IE2100 Series uses for name/IP-address Step 1 Boot the system without a configuration. When the system finishes booting, a login resolution. Secondary DNS nameserver IP address Optional. To skip, press Enter. prompt appears. Step 2 Log in with the username of setup.
Run the Setup Program (continued) Verify Configuration Registrar is Running If you have reached the Configuration Once the system has been installed and configured, Registrar. Registrar Home page, you have verified the successful installation on the Configuration you can verify the installation of the Configuration Registrar by following these steps: Step 1 Go to a different computer and bring up a web browser. Step 2 On the net-site window enter the URL for the Configuration Registrar.
Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 European Headquarters Cisco Systems Europe 11, Rue Camille Desmoulins 92782 Issy Les Moulineaux Cedex 9 France http://www-europe.cisco.com Tel: 33 1 58 04 60 00 Fax: 33 1 58 04 61 00 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.