Catalyst 3560 Switch Hardware Installation Guide February 2005 Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
C O N T E N T S Preface vii Audience Purpose vii vii Organization vii Conventions viii Related Publications xiii Obtaining Documentation xiv Cisco.
Contents Console Port 1-15 Management Options 1-15 Network Configurations CHAPTER 2 Switch Installation 1-17 2-1 Preparing for Installation 2-1 Warnings 2-2 Installation Guidelines 2-4 Verifying Package Contents 2-6 Verifying Switch Operation 2-6 Powering Off the Switch 2-7 Installing the Switch 2-7 Rack-Mounting 2-7 Removing Screws from the Switch 2-8 Attaching Brackets to the Catalyst 3560 Switch 2-9 Mounting the Switch in a Rack 2-11 Attaching the Cable Guide 2-12 Wall-Mounting 2-12 Attaching
Contents APPENDIX A Technical Specifications APPENDIX B Connector and Cable Specifications A-1 Connector Specifications B-1 10/100 and 10/100/1000 Ports SFP Module Ports B-3 Console Port B-3 B-1 B-1 Cable and Adapter Specifications B-4 Two Twisted-Pair Cable Pinouts B-4 Four Twisted-Pair Cable Pinouts for 1000BASE-T Ports Crossover Cable and Adapter Pinouts B-5 Identifying a Crossover Cable B-5 Adapter Pinouts B-6 APPENDIX C Configuring the Switch with the CLI-Based Setup Program B-4 C-1 Ac
Contents Catalyst 3560 Switch Hardware Installation Guide vi OL-6337-03
Preface Audience This guide is for the networking or computer technician responsible for installing the Catalyst 3560 switch, hereafter known as the switch. We assume that you are familiar with the concepts and terminology of Ethernet and local area networking. Purpose This guide describes the hardware features of the Catalyst 3560 switch. It describes the physical and performance characteristics of the switch, explains how to install it, and provides troubleshooting information.
Preface Conventions Appendix B, “Connector and Cable Specifications,” describes the connectors, cables, and adapters that can be used to connect to the switch. Appendix C, “Configuring the Switch with the CLI-Based Setup Program,” has an installation and setup procedure for a standalone switch. Conventions This document uses these conventions and symbols for notes, cautions, and warnings: Note Caution Warning Means reader take note.
Preface Conventions Attention IMPORTANTES INFORMATIONS DE SÉCURITÉ Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents.
Preface Conventions ¡Advertencia! INSTRUCCIONES IMPORTANTES DE SEGURIDAD Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo.
Preface Conventions Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.
Preface Conventions Catalyst 3560 Switch Hardware Installation Guide xii OL-6337-03
Preface Related Publications Related Publications You can order printed copies of documents with a DOC-xxxxxx= number. For more information, see the “Obtaining Documentation” section on page xiv. These documents provide complete information about the switch and are available from this Cisco.com site: http://www.cisco.com/univercd/cc/td/doc/product/lan/cat3560/index.
Preface Obtaining Documentation • Cisco Small Form-Factor Pluggable Modules Installation Notes (order number DOC-7815160=) • Cisco CWDM GBIC and CWDM SFP Installation Notes (not orderable but available on Cisco.com) • Cisco Small Form-Factor Pluggable Modules Compatibility Matrix (not orderable but available on Cisco.com) • Compatibility Matrix for 1000BASE-T Small Form-Factor Pluggable Modules (not orderable but available on Cisco.
Preface Documentation Feedback Documentation Feedback You can send comments about technical documentation to bug-doc@cisco.com. You can submit comments by using the response card (if present) behind the front cover of your document or by writing to the following address: Cisco Systems Attn: Customer Document Ordering 170 West Tasman Drive San Jose, CA 95134-9883 We appreciate your comments.
Preface Obtaining Additional Publications and Information To open a service request by telephone, use one of the following numbers: Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227) EMEA: +32 2 704 55 55 USA: 1 800 553 2447 For a complete list of Cisco TAC contacts, go to this URL: http://www.cisco.com/techsupport/contacts Definitions of Service Request Severity To ensure that all service requests are reported in a standard format, Cisco has established severity definitions.
Preface Obtaining Additional Publications and Information • iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies learn how they can use technology to increase revenue, streamline their business, and expand services. The publication identifies the challenges facing these companies and the technologies to help solve them, using real-world case studies and business strategies to help readers make sound technology investment decisions.
Preface Obtaining Additional Publications and Information Catalyst 3560 Switch Hardware Installation Guide xviii OL-6337-03
C H A P T E R 1 Product Overview The Catalyst 3560 switch—also referred to as the switch—is an Ethernet switch to which you can connect devices like Cisco Wireless Access Point workstations, Cisco IP Phones, and other network devices such as servers, routers, and other switches. This chapter provides a functional overview of the Catalyst 3560 switch.
Chapter 1 Product Overview Front Panel Description • Gigabit Ethernet – Catalyst 3560G-24PS switch—24 10/100/1000 PoE ports and 4 SFP module slots – Catalyst 3560G-24TS switch—24 10/100/1000 ports and 4 SFP module slots – Catalyst 3560G-48PS switch—48 10/100/1000 PoE ports and 4 SFP module slots – Catalyst 3560G-48TS switch—48 10/100/1000 ports and 4 SFP module slots • The switches support these SFP modules: – 1000BASE-SX – 1000BASE-LX – 1000BASE-ZX – 1000BASE-T – 100BASE-FX – Coarse Wavelength-Divisi
Chapter 1 Product Overview Front Panel Description FastEthernet Switch Front Panel Descriptions The 10/100 PoE ports on the Catalyst 3560-24PS switch are grouped in pairs. The first member of the pair (port 1) is above the second member (port 2) on the left, as shown in Figure 1-1. Port 3 is above port 4, and so on. The SFP module slots are numbered 1 and 2.
Chapter 1 Product Overview Front Panel Description The 10/100 PoE ports on the Catalyst 3560-48PS switch are grouped in pairs. The first member of the pair (port 1) is above the second member (port 2) on the left, as shown in Figure 1-3. Port 3 is above port 4, and so on. The SFP module slots are numbered 1 to 4.
Chapter 1 Product Overview Front Panel Description Gigabit Ethernet Switch Front Panel Descriptions The 10/100/1000 PoE ports on the Catalyst 3560G-24PS switch are grouped in pairs. The first member of the pair (port 1) is above the second member (port 2) on the left, as shown in Figure 1-5. Port 3 is above port 4, and so on. The SFP module slots are numbered 25 to 28.
Chapter 1 Product Overview Front Panel Description The 10/100/1000 PoE ports on the Catalyst 3560G-48PS switch are grouped in pairs. The first member of the pair (port 1) is above the second member (port 2) on the left, as shown in Figure 1-7. Port 3 is above port 4, and so on. The SFP module slots are numbered 49 to 52.
Chapter 1 Product Overview Front Panel Description When set for autonegotiation, the port senses the speed and duplex settings of the attached device and advertises its own capabilities. If the connected device also supports autonegotiation, the switch port negotiates the best connection (the fastest line speed that both devices support and full-duplex transmission if the attached device supports it) and configures itself accordingly. In all cases, the attached device must be within 328 feet (100 meters).
Chapter 1 Product Overview Front Panel Description For information about Cisco IP Phones and Cisco Aironet Access Points, see the documentation that came with your IP phone or access point. Note 100BASE-TX and 1000BASE-T traffic requires Category 5 cable. 10BASE-T traffic can use Category 3 or Category 4 cables. When connecting the switch to workstations, servers, routers, and Cisco IP Phones, be sure that the cable is a straight-through cable.
Chapter 1 Product Overview Front Panel Description • 100BASE-FX • CWDM For more information about these SFP modules, see your SFP module documentation. SFP Module Patch Cable The Catalyst 3560 switch supports the SFP module patch cable, a 1/2 meter, copper, passive cable with SFP module connectors at each end (see Figure 1-9). The patch cable can connect two Catalyst 3560 switches in a cascaded configuration.
Chapter 1 Product Overview Front Panel Description Figure 1-10 Catalyst 3560 Switch LEDs 8 SYST RPS STAT DUPLX SPEED PoE 1 1X 2 3 4 5 MODE 6 7 8 9 10 11 12 11X 1 Note 2 3 4 5 6 7 1 Mode button 5 Status LED 2 PoE LED 6 RPS LED 3 Speed LED 7 System LED 4 Duplex LED 8 Port LEDs 12X 97913 2X The PoE LED is only visible on Catalyst 3560 switches that support PoE. System LED The System LED shows whether the system is receiving power and is functioning properly.
Chapter 1 Product Overview Front Panel Description RPS LED The RPS LED shows the RPS status. Table 1-2 lists the LED colors and their meanings. Table 1-2 RPS LED Color RPS Status Off RPS is off or not properly connected. Green RPS is connected and ready to provide back-up power, if required. Blinking green RPS is connected but is unavailable because it is providing power to another device (redundancy has been allocated to a neighboring device).
Chapter 1 Product Overview Front Panel Description Table 1-4 lists the PoE mode LED colors and their meanings. The PoE LED applies only to Catalyst 3560 switches that support PoE. Table 1-4 PoE Mode LED Color PoE Status Off PoE mode is not selected. None of the 10/100 or 10/100/1000 PoE ports have been denied power or are in a fault condition. Green PoE mode is selected, and the PoE status is shown on the port LEDs. Blinking amber PoE mode is not selected.
Chapter 1 Product Overview Front Panel Description Table 1-5 Meaning of Port LED Colors in Different Modes on the Switch (continued) Port Mode LED Color Meaning STAT (port status) Off No link, or port was administratively shut down. Green Link present. Blinking green Activity. Port is transmitting or receiving data. Alternating green-amber Link fault.
Chapter 1 Product Overview Rear Panel Description Rear Panel Description The Catalyst 3560 switch rear panel has an AC power connector, an RPS connector, and an RJ-45 console port. (See Figure 1-11 and Figure 1-12 for examples of the Catalyst 3560 rear panels.) Figure 1-11 Catalyst 3560-24PS and 3560-48PS Switch Rear Panel CONSOL E 1 2 3 1 RJ-45 console port 2 AC power connector 4 Figure 1-12 DC INPU TS FOR REMOTE POWER SPECIFIE SUPPLY D IN MAN +12v UAL @7.5A -48 @7.
Chapter 1 Product Overview Management Options Internal Power Supply Connector The internal power supply is an autoranging unit that supports input voltages between 100 and 240 VAC. Use the supplied AC power cord to connect the AC power connector to an AC power outlet. Cisco RPS Connector The switch is powered through the internal power supply. You can also connect the Cisco RPS 675 redundant power supply (model PWR675-AC-RPS-N1=) to provide backup power if the switch internal power supply should fail.
Chapter 1 Product Overview Management Options – Solaris http://www.cisco.com/pcgi-bin/Support/ClusterMgmtSuite/cms_plugin_redirect.cgi?platform =solaris&version=1.2 From CMS, you can fully configure and monitor a switch or switch clusters, display network topologies to gather link information, and display switch images to modify switch- and port-level settings. For more information, see the “Getting Started with CMS” chapter of the switch software configuration guide on Cisco.
Chapter 1 Product Overview Management Options Network Configurations See the switch software configuration guide on Cisco.com for an explanation of network configuration concepts. The software configuration guide also provides examples of network configurations that use the switch to create dedicated network segments that are interconnected through Ethernet connections.
Chapter 1 Product Overview Management Options Catalyst 3560 Switch Hardware Installation Guide 1-18 OL-6337-03
C H A P T E R 2 Switch Installation This chapter describes how to start your switch and how to interpret the power-on self-test (POST) that ensures proper operation. It also describes how to install the switch and how to make connections to the switch.
Chapter 2 Switch Installation Preparing for Installation Warnings These warnings are translated into several languages in the Regulatory Compliance and Safety Information for the Catalyst 3560 Switch document that shipped with the switch. Warning Voltages that present a shock hazard may exist on Power over Ethernet (PoE) circuits if interconnections are made using uninsulated exposed metal contacts, conductors, or terminals.
Chapter 2 Switch Installation Preparing for Installation Warning This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal use. Statement 39 Warning When installing or replacing the unit, the ground connection must always be made first and disconnected last. Statement 1046 Warning To prevent the switch from overheating, do not operate it in an area that exceeds the maximum recommended ambient temperature of 113°F (45°C).
Chapter 2 Switch Installation Preparing for Installation Warning Ethernet cables must be shielded when used in a central office environment. Statement 171 Warning Avoid direct exposure to the laser beam. Statement 1012 Warning Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments.
Chapter 2 Switch Installation Preparing for Installation Table 2-1 SFP Module CWDM Fiber-Optic SFP Module Port Cabling Specifications (continued) Wavelength (nanometers) 1470, 1490, 1510, 1530, 1550, 1570, 1590, 1610 Fiber Type Core Size (micron) Modal Bandwidth (MHz/km) Cable Distance SMF 9/125 — 62 miles (100 km) 1. A mode-conditioning patch cord is required.
Chapter 2 Switch Installation Verifying Switch Operation Verifying Package Contents Note Carefully remove the contents from the shipping container, and check each item for damage. If any item is missing or damaged, contact your Cisco representative or reseller for support. Return all packing material to the shipping container, and save it.
Chapter 2 Switch Installation Installing the Switch When the switch powers on, it automatically begins the POST, a series of tests that verifies that the switch functions properly. When the switch begins POST, the system LED slowly blinks green. When POST completes, the system LED blinks amber. If POST fails, the system LED remains amber. If POST completes successfully, the system LED rapidly blinks green. Note POST failures are usually fatal. Call Cisco Systems if your switch does not pass POST.
Chapter 2 Switch Installation Installing the Switch Warning Note To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety: • This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
Chapter 2 Switch Installation Installing the Switch Attaching Brackets to the Catalyst 3560 Switch The bracket orientation and the brackets that you use depend on whether you are attaching the brackets for a 19-inch or a 24-inch rack. For 19-inch racks, use bracket part number 700-8209-01; for 24-inch racks, use bracket part number 700-13248-01. Figure 2-2 through Figure 2-7 show how to attach each type bracket to one side of the switch.
Chapter 2 Switch Installation Installing the Switch Attaching Brackets for 19-Inch Racks to a Catalyst 3560 Switch, Rear Panel Forward 97919 Figure 2-4 DC IN PUTS FOR RE POWE MO SPECIFI R SUPPLY TE ED IN +12v @7.5A MANUAL -48 @ 7.8A RATIN G 100-200 V~ 5.0A-2 .5A, 50 -60 HZ 1 1 Phillips flat-head screws Attaching Brackets for 24-Inch Racks to a Catalyst 3560 Switch, Rear Panel Forward 97920 Figure 2-5 DC IN PUTS FOR RE POWE MO SPECIFI R SUPPLY TE ED IN +12v @7.5A MANUAL -48 @ 7.
Chapter 2 Switch Installation Installing the Switch 40 41 42 43 44 Attaching Brackets for 24-Inch Telco Racks to a Catalyst 3560 Switch 45 46 47 Catalyst 3560 48 97922 Figure 2-7 SERIES PoE-48 47X 1 3 48X 1 2 4 1 Phillips flat-head screws Mounting the Switch in a Rack After the brackets are attached to the switch, use the four supplied number-12 Phillips machine screws to securely attach the brackets to the rack, as shown in Figure 2-8.
Chapter 2 Switch Installation Installing the Switch Attaching the Cable Guide We recommend attaching the cable guide to prevent the cables from obscuring the front panel of the switch and the other devices installed in the rack. Use the supplied black screw shown in Figure 2-9 to attach the cable guide to the left or right bracket.
Chapter 2 Switch Installation Installing the Switch Attaching the Brackets to the Switch for Wall Mounting Figure 2-10 shows how to attach a 19-inch bracket to one side of the switch. Follow the same steps to attach the second bracket to the opposite side.
Chapter 2 Switch Installation Installing the Switch Mounting the Switch on a Wall For the best support of the switch and cables, make sure the switch is attached securely to wall studs or to a firmly attached plywood mounting backboard. Mount the switch with the front panel facing up, as shown in Figure 2-12. To comply with safety regulations, mount switches on a wall with the front panel facing up.
Chapter 2 Switch Installation Installing and Removing SFP Modules Table- or Shelf- Mounting Follow these steps to install the switch on a table or shelf: Step 1 Locate the adhesive strip with the rubber feet in the mounting-kit envelope. Attach the four rubber feet on the bottom of the switch near the four corners. Note Step 2 Do not attach the rubber feet over the recessed screw holes on the bottom of the switch. Place the switch on the table or shelf near an AC power source.
Chapter 2 Switch Installation Installing and Removing SFP Modules Installing SFP Modules into SFP Module Slots Figure 2-13 shows an SFP module that has a bale-clasp latch. Caution We strongly recommend that you do not install or remove fiber-optic SFP modules with cables attached because of the potential damage to the cables, the cable connector, or the optical interfaces in the SFP module. Disconnect all cables before removing or installing an SFP module.
Chapter 2 Switch Installation Installing and Removing SFP Modules Caution Step 6 Do not remove the dust plugs from the fiber-optic SFP module port or the rubber caps from the fiber-optic cable until you are ready to connect the cable. The plugs and caps protect the SFP module ports and cables from contamination and ambient light. Insert the cable connector into the SFP module: • For fiber-optic SFP modules, insert the LC or MT-RJ cable connector into the SFP module.
Chapter 2 Switch Installation Inserting and Removing the SFP Module Patch Cable Step 5 For fiber-optic SFP modules, insert a dust plug into the optical ports of the SFP module to keep the optical interfaces clean. Step 6 Place the removed SFP module in an antistatic bag or other protective environment.
Chapter 2 Switch Installation Connecting to the 10/100 or 10/100/1000 Ports Connecting to the 10/100 or 10/100/1000 Ports The switch 10/100 and 10/100/1000 ports configure themselves to operate at the speed of attached devices. If the attached ports do not support autonegotiation, you can explicitly set the speed and duplex parameters. Connecting devices that do not autonegotiate or that have their speed and duplex parameters manually set can reduce performance or result in no linkage.
Chapter 2 Switch Installation Connecting to the 10/100 or 10/100/1000 Ports The Auto-MDIX feature is enabled by default on switches running Cisco IOS Release 12.2(18)SE or later. For releases between Cisco IOS Release 12.1(14)EA1 and 12.2(18)SE, the Auto-MDIX feature is disabled by default. For configuration information for this feature, see the switch software configuration guide or the switch command reference.
Chapter 2 Switch Installation Connecting to SFP Modules Connecting to SFP Modules This section describes how to connect to SFP modules. For instructions on how to connect to fiber-optic SFP modules, see the “Connecting to Fiber-Optic SFP Modules” section. For instructions on how to connect to copper 1000BASE-T SFP modules, see the “Connecting to 1000BASE-T SFP Modules” section.
Chapter 2 Switch Installation Connecting to SFP Modules Figure 2-19 Connecting to a Fiber-Optic SFP Module Port 40 41 42 43 44 45 46 47 Catalyst 3560 SE 48 RIES PoE-48 47X 1 48X 97931 3 2 4 1 1 Step 5 LC connector If necessary, reconfigure and restart the switch or target device.
Chapter 2 Switch Installation Where to Go Next Figure 2-20 40 41 42 Connecting to a 1000BASE-T SFP Module 43 44 45 46 47 Catalyst 48 3560 SERI ES PoE-48 47X 1 48X 97932 3 2 4 1 1 RJ-45 connector Step 2 Insert the other cable end in an RJ-45 connector on a target device. Step 3 Observe the port status LED. The LED turns green when the switch and the target device have an established link. The LED turns amber while the STP discovers the network topology and searches for loops.
Chapter 2 Switch Installation Where to Go Next c. Download the Network Assistant installer, and run it. (You can run it directly from the web if your browser offers this choice.) d. When you run the installer, follow the displayed instructions. In the final panel, click Finish to complete Network Assistant installation. See the Network Assistant online help and the getting started guide for more information.
C H A P T E R 3 Troubleshooting The LEDs on the front panel provide troubleshooting information about the switch. They show failures in the power-on self-test (POST), port-connectivity problems, and overall switch performance. For a full description of the switch LEDs, see the “LEDs” section on page 1-9. You can also get statistics from the browser interface, from the command-line interface (CLI), or from a Simple Network Management Protocol (SNMP) workstation.
Chapter 3 Troubleshooting Diagnosing Problems Table 3-1 describes how to detect and resolve these problems. Table 3-1 Common Problems and Their Solutions Symptom Possible Cause Resolution Poor performance or excessive errors Duplex autonegotiation mismatch. See the switch software configuration guide for information on identifying autonegotiation mismatches. Cabling distance exceeded • Port statistics show excessive frame check sequence (FCS), late-collision, or alignment errors.
Chapter 3 Troubleshooting Diagnosing Problems Table 3-1 Common Problems and Their Solutions (continued) Symptom Possible Cause Resolution No connectivity Incorrect or bad cable These are results of no link at both ends: • A crossover cable was used when a straight-through was required, or the reverse. • For the correct pinouts and the proper application of crossover instead of straight-through cables, see the “Two Twisted-Pair Cable Pinouts” section on page B-4.
Chapter 3 Troubleshooting Diagnosing Problems Table 3-1 Common Problems and Their Solutions (continued) Symptom Possible Cause Resolution The switch port is placed in error-disabled state after SFP module is inserted Bad or non-Cisco-approved SFP. Remove the SFP module from the switch, and replace it with a Cisco-approved module. Use the errdisable recovery cause gbic-invalid global configuration command to verify the port status, and enter a time interval to recover from the error-disable state.
Chapter 3 Troubleshooting Diagnosing Problems Table 3-1 Common Problems and Their Solutions (continued) Symptom Possible Cause Resolution Powered device connected to PoE port, but no power given PoE might be disabled on switch port. Use the Mode button to show the PoE status for all ports. If the port status LED is amber, configure the switch port PoE setting to Auto. Note PoE is enabled by default.
Chapter 3 Troubleshooting Diagnosing Problems Table 3-1 Common Problems and Their Solutions (continued) Symptom Possible Cause Resolution The switch port is placed in error-disabled state after SFP is inserted Bad or non-Cisco-approved SFP. Remove the SFP module from the switch, and replace it with a Cisco-approved module. Use the errdisable recovery cause gbic-invalid global configuration command to verify the port status, and enter a time interval to recover from the error-disable state.
A P P E N D I X A Technical Specifications This appendix lists the switch technical specifications in Table A-1 to Table A-8.
Appendix A Table A-2 Technical Specifications Specifications for the Catalyst 3560-48PS Switch Environmental Ranges Operating temperature 32 to 113°F (0 to 45°C) Storage temperature –13 to 158°F (–25 to 70°C) Relative humidity 10 to 85% (noncondensing) Operating altitude Up to 10,000 ft (3049 m) Storage altitude Up to 15,000 ft (4573 m) Power Requirements AC input voltage 100 to 240 VAC (autoranging) 5.5 to 2.
Appendix A Technical Specifications Table A-3 Specifications for the Catalyst 3560-24TS-S Switch Environmental Ranges Operating temperature 32 to 113°F (0 to 45°C) Storage temperature –13 to 158°F (–25 to 70°C) Relative humidity 10 to 85% (noncondensing) Operating altitude Up to 10,000 ft (3049 m) Storage altitude Up to 15,000 ft (4573 m) Power Requirements AC input voltage 100 to 240 VAC (autoranging) 50 to 60 Hz DC input voltages for RPS 675 + 12 V Power consumption 45 W Power dissipat
Appendix A Table A-5 Technical Specifications Specifications for the Catalyst 3560G-24TS Switch Environmental Ranges Operating temperature 32 to 113°F (0 to 45°C) Storage temperature –13 to 158°F (–25 to 70°C) Relative humidity 10 to 85% (noncondensing) Operating altitude Up to 10,000 ft (3049 m) Storage altitude Up to 15,000 ft (4573 m) Power Requirements AC input voltage 100 to 240 VAC (autoranging) 1.
Appendix A Technical Specifications Table A-6 Specifications for the Catalyst 3560G-24PS Switch Environmental Ranges Operating temperature 32 to 113°F (0 to 45°C) Storage temperature –13 to 158°F (–25 to 70°C) Relative humidity 10 to 85% (noncondensing) Operating altitude Up to 10,000 ft (3049 m) Storage altitude Up to 15,000 ft (4573 m) Power Requirements AC input voltage 100 to 240 VAC (autoranging) 4 to 8 A, 50 to 60 Hz DC input voltages for RPS 675 + 12 V Power consumption 520 W Powe
Appendix A Table A-7 Technical Specifications Specifications for the Catalyst 3560G-48TS Switch Environmental Ranges Operating temperature 32 to 113°F (0 to 45°C) Storage temperature –13 to 158°F (–25 to 70°C) Relative humidity 10 to 85% (noncondensing) Operating altitude Up to 10,000 ft (3049 m) Storage altitude Up to 15,000 ft (4573 m) Power Requirements AC input voltage 100 to 240 VAC (autoranging) 3 to 1.
Appendix A Technical Specifications Table A-8 Specifications for the Catalyst 3560G-48PS Switch Environmental Ranges Operating temperature 32 to 113°F (0 to 45°C) Storage temperature –13 to 158°F (–25 to 70°C) Relative humidity 10 to 85% (noncondensing) Operating altitude Up to 10,000 ft (3049 m) Storage altitude Up to 15,000 ft (4573 m) Power Requirements AC input voltage 100 to 240 VAC (autoranging) 4 to 8 A, 50 to 60 Hz DC input voltages for RPS 675 + 12 V Power consumption 560 W Powe
Appendix A Technical Specifications Catalyst 3560 Switch Hardware Installation Guide A-8 OL-6337-03
A P P E N D I X B Connector and Cable Specifications This appendix describes the Catalyst 3560 switch ports and the cables and adapters that you use to connect the switch to other devices. Connector Specifications These sections describe the connectors used with the Catalyst 3560 switch. 10/100 and 10/100/1000 Ports The 10/100 and 10/100/1000 Ethernet ports use standard RJ-45 connectors and Ethernet pinouts with internal crossovers.
Appendix B Connector and Cable Specifications Connector Specifications Figure B-2 shows the pinout for a 10/100/1000 port. Caution 10/100/1000 Port Pinouts Pin Label 1 TP0+ 2 TP0- 3 TP1+ 4 TP2+ 5 TP2- 6 TP1- 7 TP3+ 8 TP3- 1 2 3 4 5 6 7 8 60915 Figure B-2 PoE faults are caused when noncompliant cabling or powered devices are connected to a PoE port. Only standard-compliant cabling can be used to connect Cisco pre-standard IP Phones or wireless access points or IEEE 802.
Appendix B Connector and Cable Specifications Connector Specifications Note Use a straight-through cable to connect two ports only when one port is designated with an X. Use a crossover cable to connect two ports when both ports are designated with an X or when both ports do not have an X. This applies only to switches on which Auto-MDIX is disabled. SFP Module Ports The Catalyst 3560 switch uses SFP modules for fiber-optic and copper uplinks.
Appendix B Connector and Cable Specifications Cable and Adapter Specifications Cable and Adapter Specifications These sections describe the cables and adapters used with Catalyst 3560 switches. Two Twisted-Pair Cable Pinouts Figure B-5 and Figure B-6 show the schematics of two twisted-pair cables for connecting to 10BASE-Tand 100BASE-TX-compatible devices.
Appendix B Connector and Cable Specifications Cable and Adapter Specifications Four Twisted-Pair Crossover Cable Schematics for 1000BASE-T Ports Switch Switch 1 TPO+ 1 TP0+ 2 TPO- 2 TP0- 3 TP1+ 3 TP1+ 6 TP1- 6 TP1- 4 TP2+ 4 TP2+ 5 TP2- 5 TP2- 7 TP3+ 7 TP3+ 8 TP3- 8 TP3- 65274 Figure B-8 Crossover Cable and Adapter Pinouts This section describes how to identify a crossover cable and also describes the adapter pinouts.
Appendix B Connector and Cable Specifications Cable and Adapter Specifications Adapter Pinouts Table B-1 lists the pinouts for the console port, the RJ-45-to-DB-9 adapter cable, and the console device.
A P P E N D I X C Configuring the Switch with the CLI-Based Setup Program This appendix provides a command-line interface (CLI)-based setup procedure for a standalone switch. For product overview information, see Chapter 1, “Product Overview.” Before connecting the switch to a power source, review the safety warnings in Chapter 2, “Switch Installation.
Appendix C Configuring the Switch with the CLI-Based Setup Program Taking Out What You Need After you have entered the configuration information for the switch, save it to flash memory by using the write memory privileged EXEC command. Note While in Express Setup mode, the IP address 10.0.0.1 is active until you enter the write memory command. You lose the Telnet connection after entering the write memory command.
Appendix C Configuring the Switch with the CLI-Based Setup Program Connecting to the Console Port 1 Catalyst 3560 switch 2 RJ-45-to-DB-9 adapter cable 3 AC power cord Note You need to provide the Category 5 straight-through cables to connect the switch ports to other Ethernet devices. Note You can use the mdix auto interface configuration command in the CLI to enable the automatic medium-dependent interface crossover (Auto-MDIX) feature.
Appendix C Configuring the Switch with the CLI-Based Setup Program Starting the Terminal-Emulation Software Figure C-2 Connecting a Switch to a PC 1 CONSOL E RATING 100-200V ~ 5.0A-2.5A , 50-60 DC INPU TS FOR REMOTE POWER SPECIFIE SUPPLY D IN MAN +12v UAL @7.5A -48 @7.
Appendix C Configuring the Switch with the CLI-Based Setup Program Connecting to a Power Source Follow these steps to start a terminal-emulation session: Step 1 Start the terminal-emulation program if you are using a PC or terminal.
Appendix C Configuring the Switch with the CLI-Based Setup Program Entering the Initial Configuration Information Entering the Initial Configuration Information To set up the switch, you need to complete the setup program, which runs automatically after the switch is powered up. You must assign an IP address and other configuration information necessary for the switch to communicate with the local routers and the Internet.
Appendix C Configuring the Switch with the CLI-Based Setup Program Entering the Initial Configuration Information Step 4 Enter an enable password, and press Return. Enter enable password: enable_password Step 5 Enter a virtual terminal (Telnet) password, and press Return. The password can be from 1 to 25 alphanumeric characters, is case sensitive, allows spaces, but ignores leading spaces.
Appendix C Configuring the Switch with the CLI-Based Setup Program Entering the Initial Configuration Information ! interface GigabitEthernet2/0/28 ! end Step 10 These choices are displayed: [0] Go to the IOS command prompt without saving this config. [1] Return back to the setup without saving this config. [2] Save this configuration to nvram and exit. If you want to save the configuration and use it the next time the switch reboots, save it in NVRAM by selecting option 2.
I N D EX Auto-MDIX Numerics 2-22 autonegotiation 1-7 10/100/1000 ports Auto-MDIX feature cable lengths 1-8 B 2-4 connectors and cables described 1-6 illustrated 1-5 pinouts PoE B-1 to B-3 brackets See mounting brackets B-2 C 1-7 10/100 ports cable guide, attaching Auto-MDIX feature cable lengths 2-4 connecting to 2-19 1-8 cable lengths 2-12 2-4 cables crossover connectors and cables B-1 to B-3 connecting to B-2 described 1-6 four twisted-pair pinout, 1000BASE-T ports il
Index Cisco IOS command-line interface Cisco IP Phones, connecting to Cisco Network Assistant connectivity problems 1-16 3-3 pinout 1-7, 2-19 four twisted-pair, 1000BASE-T ports 1-16 Cisco RPS CWDM SFP module B-5 1-9 See RPS CiscoView CLI 1-16 D 1-16 accessing by using Express Setup accessing through console port C-1 C-2 RPS Cluster Management Suite 1-2 diagnosing problems See CMS CMS DC power 3-1 document conventions 1-15 duplex LED viii 1-11 command-line interface See CLI co
Index I N installation network configuration examples assigning the IP Address connecting to a power source rack-mounting 2-7 to 2-11 shelf-mounting 2-15 site requirements noise, electrical C-6 P packing list starting the terminal emulation software 2-15 wall-mounting 2-12 2-5 C-5 2-4 table-mounting 1-1 C-4 2-6 performance problems, solving 3-1 pinouts 10/100/1000 ports See also procedures 10/100 ports installing SFP modules 2-16 to 2-17 adapters B-3 B-5 console port B-6,
Index numbering of 10/100/1000 1-6 numbering of SFP module ports S 1-3 safety POST LEDs SFP module patch cable 3-1, C-5 results description 3-1, C-5 1-9 installing and removing power connecting to connectors power on 1-14 2-6 1000BASE-LX 1-8 1000BASE-SX 1-8 1000BASE-T 1-8 supported speeds 1-11 1000BASE-ZX power supply AC power outlet RPS connector 1-9 bale-clasp latch 1-14 removal procedures 2-17 connection 2-19 to 2-23 connecting to installation 2-7 to 2-15 connectors
Index T table-mounting 2-15 technical specifications telco racks A-1 2-7 Telnet, and accessing the CLI temperature, operating A-1 terminal emulation software troubleshooting 1-16 C-4 3-1 to 3-3 W wall-mounting 2-12 warnings defined viii installation 2-2 Catalyst 3560 Switch Hardware Installation Guide OL-6337-03 IN-5
Index Catalyst 3560 Switch Hardware Installation Guide IN-6 OL-6337-03
