Quick Start Guide Cisco 3620 and Cisco 3640 Modular Access Routers INCLUDING LICENSE AND WARRANTY Installation, License and Warranty 1 Cisco 90-Day Limited Hardware Warranty Terms 2 Documents, Equipment, and Tools 3 Install Chassis 4 Connect Cables 5 Power Up the Router 6 Perform Initial Configuration 7 Interface Numbering 8 Where to Go Next 9 Obtaining Documentation 10 Documentation Feedback 11 Obtaining Technical Assistance 12 Obtaining Additional Publications and Information
1 Cisco 90-Day Limited Hardware Warranty Terms There are special terms applicable to your hardware warranty and various services that you can use during the warranty period. Your formal Warranty Statement, including the warranties and license agreements applicable to Cisco software, is available on Cisco.com. Follow these steps to access and download the Cisco Information Packet and your warranty and license agreements from Cisco.com. 1. Launch your browser, and go to this URL: http://www.cisco.
2 Documents, Equipment, and Tools User Documentation All the documents referenced in this quick start guide are available online and on the Cisco documentation CD-ROM. To be sure of obtaining the latest information, you should access the online documentation. To view or print a document in its original page format, access the online document, and click on the PDF icon. For information about accessing user documentation, see the “Where to Go Next” section on page 32.
Warning Definition IMPORTANT SAFETY INSTRUCTIONS Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. To see translations of the warnings that appear in this publication, refer to the translated safety warnings that accompanied this device.
Avvertenza IMPORTANTI ISTRUZIONI SULLA SICUREZZA Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Per le traduzioni delle avvertenze riportate in questo documento, vedere le avvertenze di sicurezza che accompagnano questo dispositivo.
Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.
Advarsel VIGTIGE SIKKERHEDSANVISNINGER Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed.
Warning This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security. Statement 1017 Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals.
Warning To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables. Statement 1021 Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor.
Attaching Brackets Attach the mounting brackets to the chassis as shown in the applicable figure, Figure 1 through Figure 8, using the Phillips-head screws provided. Attach the second bracket to the opposite side of the chassis. Note When installed in a 19-inch rack with a 17.5-inch opening, Cisco 3620 and Cisco 3640 routers protrude beyond the front of the rack. Cisco 3620 or Cisco 3640 Bracket Attachment—Front Panel Forward (19-Inch Rack with a 17.
Figure 3 Cisco 3620 or Cisco 3640 Bracket Attachment—Front Panel Forward (23- or 24-Inch Rack) 0 1 2 3 ACTIVE H6252 1 READY 0 PCMCIA Note: The second bracket attaches to the other side of the chassis. Cisco 3620 or Cisco 3640 Bracket Attachment—Rear Panel Forward (19-Inch Rack with a 17.5-Inch Opening) 26323 Figure 4 WO BRI S/T AUI EN Note: The second bracket attaches to the other side of the chassis.
Cisco 3620 or Cisco 3640 Bracket Attachment—Rear Panel Forward (19-Inch Rack with a 17.75-Inch Opening) 15854 Figure 5 WO BRI S/T AUI EN Note: The second bracket attaches to the other side of the chassis. Cisco 3620 or Cisco 3640 Bracket Attachment—Rear Panel Forward (23- or 24-Inch Rack) 15855 Figure 6 WO BRI S/T AUI EN Note: The second bracket attaches to the other side of the chassis.
Figure 8 Cisco 3640 Center-Mount Bracket Attachment (Requires Optional NEBS/ETSI Kit) 0 1 2 3 ACTIVE 1 READY 0 10970 PCMCIA Note: The second bracket attaches to the other side of the chassis. Installing Chassis in Rack Install the chassis in the rack, using the screws provided with the rack. Rack-mounting screws are not provided with the router. Use two screws for each side.
Installing on a Desktop If you are mounting a Cisco 3620 on a desktop, you must install the rubber feet that are supplied in the accessory kit. They provide a space for air circulation. Peel the rubber feet from the adhesive strip, and attach one foot at each corner to the bottom of the chassis. Caution If you place the Cisco 3620 or Cisco 3640 router on a desktop, do not place anything that weighs more than 10 lb (4.5 kg) on top of the chassis.
Figure 11 Required Ground-Lug Bracket Attachment on a Cisco 3640 Router (DC Power Supply Shown) Mounting screws Bracket Step 2 15846 Power supply Strip one end of the ground wire to the length required for the ground lug or terminal. • For the NEBS ground lug—approximately 0.75 in. (20 mm) • For user-provided ring terminal—as required Step 3 Crimp the ground wire to the ground lug or ring terminal, using a crimp tool of the appropriate size.
Figure 13 NEBS-Compliant Ground Lug Attachment on a Cisco 3620 Router with Redundant Power Supply (Cisco RPS) DC INPUT FOR USE WITH CISCO RPS +5V– – –14A, +12V– – –5A, -12V– – –3A Ground lug mounted on a Cisco 3620 router with Cisco RPS Figure 14 15851 Bracket Power supply NEBS-Compliant Ground Lug Attachment on a Cisco 3640 Router Ground lug Ground Lug Attachment Using Ring Terminal on a Cisco 3620 Router with Internal AC or DC Power Supply 103009 Figure 15 15847 Power supply Ring terminal at
Figure 16 Ground Lug Attachment Using Ring Terminal on a Cisco 3620 Router with Redundant Power Supply (Cisco RPS) DC INPUT FOR USE WITH CISCO RPS +5V– – –14A, +12V– – –5A, -12V– – –3A Ring terminal attached to a bracket Figure 17 Power supply 103010 Bracket Ground Lug Attachment Using Ring Terminal on a Cisco 3640 Router Power supply 103011 Ring terminal 17
4 Connect Cables Warning Do not work on the system, or connect or disconnect cables during periods of lightning activity. Statement 1001 System Management Connections The connections described in Table 1 provide system management access.
DC Wiring Requirements Cisco 3620 and Cisco 3640 routers with a DC-input power supply require copper wire for the power connections. For Cisco 3640 routers, DC power connections require crimp-type ring terminals or spade terminals with upturned lugs. Table 2 DC Wiring Requirements for Cisco 3620 and Cisco 3640 Routers DC Power Source Nominal 48 VDC DC Input –48 to –60 DC Input Wire Size VDC1, 4A AWG 14 (2.0 mm2) Safety Ground Wire Size AWG 14 (2.0 mm2) Overcurrent Protection 15A, maximum 1.
DC Power Connections for Cisco 3620 Routers (Typical) + - H7477 Figure 18 Terminal block On/off switch Figure 19 Positive Negative Ground DC Power Connections for Cisco 3640 Routers (Typical) Negative Terminal block Ground Positive On/off switch 72331 Terminal block Step 4 Secure the wires using cable ties. Step 5 Turn on power to the DC circuit.
WAN, LAN, and Voice Connections The connections described here are described in detail in the following documents: • Cisco 3600 Series Hardware Installation Guide • Cisco Network Modules Hardware Installation Guide • Cisco Interface Cards Installation Guide • Cisco Modular Access Router Cable Specifications To locate these documents, see the “Where to Go Next” section on page 32. Table 3 summarizes some typical WAN, LAN, and voice connections for Cisco 3600 series routers.
5 Power Up the Router Checklist for Power-Up You are ready to power up the Cisco router if the following steps are completed: • Chassis is securely mounted and grounded. • Power and interface cables are connected. • Your PC terminal emulation program is configured for 9600 baud, 8 data bits, 1 stop bit, and no parity. • You have selected passwords for access control. • You have determined the IP addresses for the Ethernet and serial interfaces.
You may see different startup messages: • If you see the following messages, the router has booted with a configuration file and is ready for initial configuration using the Cisco Router and Security Device Manager (SDM): yourname con0 is now available Press RETURN to get started. See the “Initial Configuration Using Cisco Router and Security Device Manager” section on page 24 to learn how to configure your router using SDM or to learn how to obtain SDM and install it on your router.
Initial Configuration Using Cisco Router and Security Device Manager This section explains how to use Cisco Router and Security Device Manager (SDM) to configure your router. If SDM has been installed on your router, the following messages appear at the end of the startup sequence: yournname con0 is now available Press RETURN to get started.
Step 7 Exit from interface configuration mode. yourname (config-if)# exit Step 8 Enter interface configuration mode on an Ethernet interface for connection to your PC. The following example is for Ethernet interface 0 in chassis slot 1. yourname (config)# interface FastEthernet 1/0 yourname (config-if)# Step 9 Configure IP address 10.10.10.1 on this interface. yourname (config-if)# ip address 10.10.10.1 255.255.255.0 Step 10 Enter the no shutdown command to enable the interface.
Figure 21 Tip SDM Launch Page If the SDM Launch page does not appear when you enter the URL https://10.10.10.1/flash/sdm.shtml, test the connection between the PC and the router by doing the following: a. Check that the POWER LED on the router is on, and that the ACTIVITY LED is on, indicating an active Ethernet connection between the router and the PC. If the ACTIVITY LED is not on, verify that you are using a crossover cable to connect the PC to the router. b.
IP Addresses in the Renumbered Subnet for SDM Crossover cable 172.16.30.0 subnet Example static or dynamic IP address: 172.16.30.2/255.255.255.0 Step 9 Example configured IP address: 172.16.30.1/255.255.255.0 88669 Figure 22 Open a web browser on the PC, and enter the SDM URL, using the new IP address that you gave the LAN interface: https://new-IP-address/flash/sdm.shtml In the Figure 22 example, you would enter: https://172.16.30.1/flash/sdm.shtml.
Step 1 To proceed using the setup command facility, enter yes. Would you like to enter the initial configuration dialog? [yes/no]: yes Step 2 When the following messages appear, press Return to enter basic management setup: At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'.
Step 10 Respond to the following prompts as appropriate for your network: Configuring interface FastEthernet0/0: Use the 100 Base-TX (RJ-45) connector? [yes]: Operate in full-duplex mode? [no]: yes Configure IP on this interface? [yes]: IP address for this interface: 10.1.1.1 Subnet mask for this interface [255.0.0.0] : 255.255.0.0 Class A network is 10.0.0.
Initial Configuration Using the CLI (Manual Configuration) This section shows how to bring up a command-line interface (CLI) prompt for configuration using the CLI, and it directs you to documentation for the CLI configuration.You can use the CLI if you see the following messages at the end of the startup sequence: --- System Configuration Dialog --At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'.
7 Interface Numbering Each individual network interface on a Cisco 3620 or Cisco 3640 router is identified by a slot number and a unit number. Slot Numbering The Cisco 3620 or Cisco 3640 router chassis contains two or four slots in which you can install modules. You can install any module into any available slot in the chassis. For Cisco 3620 and Cisco 3640 routers, the slots are numbered as follows: • Slot 0 is at the bottom right (as viewed from the rear of the chassis), near the power supply.
8 Where to Go Next For additional detailed configuration procedures, refer to the appropriate Cisco 3600 series documentation or Cisco IOS software documentation, available online and on the Documentation CD-ROM: Tip See the “Obtaining Documentation” section on page 32 for help in locating these documents. To access Cisco 3600 series platform documentation on Cisco Connection Online (CCO): On the Cisco.com home page at http://www.cisco.
You can order Cisco documentation in these ways: • Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from the Ordering tool: http://www.cisco.com/en/US/partner/ordering/index.shtml • Nonregistered Cisco.com users can order documentation through a local account representative by calling Cisco Systems Corporate Headquarters (California, USA) at 408 526-7208 or, elsewhere in North America, by calling 800 553-NETS (6387).
For a complete list of Cisco TAC contacts, go to this URL: http://www.cisco.com/techsupport/contacts Definitions of Service Request Severity To ensure that all service requests are reported in a standard format, Cisco has established severity definitions. Severity 1 (S1)—Your network is “down,” or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation.
Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 European Headquarters Cisco Systems International BV Haarlerbergpark Haarlerbergweg 13-19 1101 CH Amsterdam The Netherlands www-europe.cisco.com Tel: 31 0 20 357 1000 Fax: 31 0 20 357 1100 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA www.cisco.
