Specifications
Table Of Contents
- Software Configuration Guide
- Contents
- Preface
- Understanding Interface Numbering and Cisco IOS Software Basics
- Understanding Interface Numbering
- Understanding Cisco IOS Software Basics
- Upgrading to a New Cisco IOS Release
- Where to Go Next
- Using the Setup Command Facility
- Before Starting Your Router
- Using the setup Command Facility
- Configuring Global Parameters
- Configuring Interface Parameters
- Completing the Configuration
- Where to Go Next
- Configuring with the Command-Line Interface
- Configuring the Host Name and Password
- Configuring 1-Port and 2-Port Ethernet Interfaces
- Configuring Fast Ethernet Interfaces
- Configuring Asynchronous/Synchronous Serial Network Modules or WAN Interface Cards
- Configuring 16-Port and 32-Port Asynchronous Network Modules
- Configuring ISDN BRI WAN Interface Cards
- Configuring T1 and E1 Interfaces
- Configuring T1 (FT1) WAN Interface Cards
- Configuring ATM Interfaces
- Configuring Inverse Multiplexing for ATM Interfaces
- Configuring Analog Modem Interfaces
- Configuring Wireless Multipoint Interfaces
- Checking the Interface Configuration
- Configuring 1-Port ADSL WAN Interface Card
- Configuring the NM-AIC-64, Contact Closure Network Module
- Configuring the 1-Port HSSI Network Module
- Configuring the Compression Network Module for the Cisco 3600 Series Routers
- Configuring the Digital Modem Network Module for the Cisco 3640 Router
- Prerequisites
- Configuration Tasks
- Configure the E1/T1 Network Module for ISDN PRI
- Configure the ISDN D-Channel Serial Interfaces
- Configure the Loopback Interface
- Configure the LAN Interface
- Create the Group Asynchronous Interface
- Configure the ISDN Dialer Interface
- Configure the Default IP Pool Information
- Configure Modem Lines for Dial-In and Dial-Out
- Configuration Example
- Configuring 1-Port G.SHDSL WAN Interface Card
- Saving Configuration Changes
- Where to Go Next
- Configuring Voice-over-IP
- Voice-over-IP Prerequisites
- Configuring the Voice Interface
- Voice-over-IP Configuration Examples
- Where to Go Next
- Configuration Examples
- Cisco 2600 Series Router Configuration Example
- Cisco 3631 Router Configuration Example
- Cisco 3725 Router Configuration Example
- 1-Port ADSL WAN Interface Card Configuration Examples
- NM-AIC-64, Contact Closure NetworkConfiguration Examples
- Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls
- Formatting the Compact Flash Memory Cards
- Using the ROM Monitor
- Index
3-41
Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers
OL-1957-03
Chapter 3 Configuring with the Command-Line Interface
Configuring the NM-AIC-64, Contact Closure Network Module
Configuring Alarms
After the AIC and NOC IP addresses have been configured, you can the configure alarms by
programming the AIC’s discrete and analog contact points. These tasks can be performed on-site or by
Telneting as described in the “Accessing the AIC” section on page 3-40.
Alarms are configured using either TL1 or AIC CLI. Information about TL1 commands can be found in
the Telcordia Technology (formerly Bellcore) document Network Maintenance: Network Element and
Transport Surveillance Messages, GR-833-CORE, Issue 5, November 1996. For a reference of
security-related commands (ACT-USER and CANC-USER) refer to Telcordia Technology’s Operations
Applications Messages-Network Element and Network System Security Admin Messages,
TR-NWT-000835, Issue 2, January 1993. The following TL1 messages and commands are supported by
the AIC:
• TL1 Messages
–
REPT-ALM-ENV
–
REPT-ALM-EQPT
–
REPT-EVT
• TL1 Commands
–
ACT-USER
–
CANC-USER
–
OPR-EXT-CONT
–
RLS-EXT-CONT
–
RTRV-ALM
–
RTRV-ALM-ENV
–
RTRV-ATTR
–
RTRV-ATTR-CONT
–
RTRV-ATTR-ENV
–
RTRV-ATTR-LOG
–
RTRV-HDR
–
RTRV-LOG
–
RTRV-EXT-CONT
–
SET-ATTR-ENV
–
SET-ATTR-EQPT
–
SET-ATTR-LOG
–
STA-LOG
–
STP-LOG
Programming the Analog Contact Points
Alarm points 57 through 64 are analog inputs, which are configurable as discrete inputs. When
configured as an analog input, the user must select whether the point is monitoring voltage or current.
The user must also define five ranges by selecting four values for a point monitoring voltage or six ranges
for a point monitoring current. For current-monitoring points, the lowest and highest values define the