QUICK START GUIDE Cisco 7301 Router 1 Documentation and Resources 2 Prepare for Installation 3 Install External Options 4 Rack-Mount the Router 5 Connect the Router to the Network 6 Start the System 7 Configure the Router 8 After Installation 9 Obtaining Technical Assistance
1 Documentation and Resources Documentation for the Cisco 7301 router is online and orderable. For detailed hardware installation instructions, refer to the online Cisco 7301 Installation and Configuration Guide. Refer to the following online documents for titles and links to related documentation for installation and replacement of parts (including port adapters), regulatory compliance information, and troubleshooting information and tools.
Warning The ports labeled “Ethernet,” “10BaseT,” “Token Ring,” “Console,” and “AUX” are safety extra-low voltage (SELV) circuits. SELV circuits should only be connected to other SELV circuits. Because the BRI circuits are treated like telephone-network voltage, avoid connecting the SELV circuit to the telephone network voltage (TNV) circuits. Statement 22 Before beginning this router installation, read the Cisco 7300 Series Internet Routers Regulatory Compliance and Safety Information.
Prepare for Workbench or Tabletop Installation For a workbench or tabletop installation, verify the following before installing the router: • The router is off the floor and has adequate ventilation. • An adequate chassis ground (earth) connection exists for the router. • The router has at last 3 inches (7.62 cm) of clearance at the inlet and exhaust vents (sides of router). • The router has 19 inches (48.
Install the SFP Gigabit Interface Converter Module Warning Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments. Statement 1051 Warning Class 1 laser product. Statement 10008 Warning Class 1 LED product. Statement 1027 Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself.
Figure 3 Inserting a SFP GBIC Module into a SFP GBIC Port TX GBIC RX 1 ETHERNET 0/0 LINK TX GBIC RX TX GIGABIT ET HERNET 0/1 RJ45 EN LINK TX GBIC RX GIGABIT ET HERNET 0/2 RJ45 EN LINK TX GBIC AUX CONSOLE RX RX SERIES 80269 COMPAC FLASH 2 1 SFP GBIC port 2 Latch beneath plug Step 1 Turn the SFP GBIC module so the latch is on the bottom. The SFP GBIC module is keyed to be inserted correctly. Step 2 Insert the SFP GBIC module into SFP port 0/0, 0/1, or 0/2.
Depending on how the rack-mount brackets are attached to the chassis, the chassis either protrudes from the rack or is recessed in the rack. Step 1 Locate the rack-mount and cable-management brackets and screws and a Number 2 Phillips screwdriver. Step 2 Align the rack-mount bracket (1) to the side of the router. Depending on which set of rack-mount bracket holes you choose to use to attach the rack-mount bracket to the router, the chassis will either be recessed in the rack or protrude from the rack.
Attach the Cable-Management Bracket Figure 6 Attaching the Cable-Management Bracket 1 D LE AB S IER LL R RM CE CAR LA RX RX RX A 80278 EN 2 Cable-management bracket 1 2 M4 x 20-mm screw Step 1 Align the cable-management bracket (1) to the rack-mount bracket on the left side of the Cisco 7301 router. Step 2 Using a Phillips screwdriver and the M4 x 20-mm screw (2), thread and tighten the screw to the cable-management bracket.
Step 1 Make sure that the port adapter latch is in the locked position and the screw is tightened. Step 2 Make sure the rack brakes are locked or the rack (1) is stabilized. Step 3 Position the router so the front is closest to you and lift it carefully into the rack. To prevent injury, avoid any sudden twists or moves. Step 4 Slide the chassis into the rack, pushing it back until the brackets meet the mounting strips or posts on both sides of the rack.
Chassis Ground Connection Installation Warning This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal use. Statement 39 Figure 9 Attaching the Grounding Lug and Wire to the Chassis 3 2 50536 4 1 1 Chassis ground connector 3 Screws 2 Grounding lug 4 Wire Note The grounding lug and Phillips screws are not available from Cisco Systems. Get the grounding lug from an electrical-connector vendor and the screws from a hardware vendor.
5 Connect the Router to the Network This section provides information about cables and ports and attaching the router to the network.
Figure 11 1 Gigabit Ethernet SFP GBIC and RJ-45 Port Identification 2 GIGABIT ETH ERNET 0/0 RJ45 EN LINK TX GBIC 3 RX 4 GIGABIT ETH ERNET 0/1 RJ45 EN LINK TX GBIC 5 6 GIGABIT ETH ERNET 0/2 RX RJ45 EN LINK TX GBIC RX AUX CONSOLE CISCO 73 01 80274 CO FL 1 Gigabit Ethernet RJ-45 port 0/0 4 Gigabit Ethernet SFP GBIC port 0/1 2 Gigabit Ethernet SFP GBIC port 0/0 5 Gigabit Ethernet RJ-45 port 0/2 3 Gigabit Ethernet RJ-45 port 0/1 6 Gigabit Ethernet SFP GBIC port 0/2 Intra-Building
Warning Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments. Statement 1051 Warning Class 1 laser product. Statement 1008 Warning Class 1 LED product.
Attach the Mode-Conditioning Patch Cord Figure 13 Attaching the Mode-Conditioning Patch Cord 4 1 // 2 // Offset 7 // TX RX 3 5 6 7 4 84159 8 1 Gray color identifier 5 Single-mode bar 2 To GE interface 6 Offset 3 Blue color identifier 7 Beige color identifier 4 Multimode bar 8 To cable plant Step 1 Attach the patch cord to the LC-type connector on the SFP GBIC modules (2).
Alarm Port Connection Figure 14 Connecting the Alarm Port Cable 1 CONSOLE ALARM 80279 COMPACT FLASH STATUS 1 Alarm port Connect the dry relay alarm port cable connector to the alarm port. It cannot be inserted incorrectly. The dry relay alarm port operates up to 50V AC/DC maximum and up to 80 mA maximum. Total power dissipation should not exceed 300 milliwatts. The normally closed position will have from 15 to 30 ohms resistance. The open position will be greater than 1 megohm.
6 Start the System Connect Power to the Router This section provides instructions for attaching the power cables to the router and powering on the router. Warning This unit might have more than one power supply connection. All connections must be removed to de-energize the unit. Statement 1028 Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A U.S.
Connect DC-Input Power The color coding of the DC-input power supply leads depends on the color coding of the DC power source at your site. Match the lead color coding for the DC-input power supply to the lead color coding used at the DC power source. Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that a Listed and Certified fuse or circuit breaker no larger than 60 VDC, 15 A is used on all currently-carrying conductors.
Step 7 Switch the circuit breaker to the ON position. Step 8 Press the power switch to turn on the router. Note After powering off the router, wait a minimum of 30 seconds before powering it on again. Observe the System Startup and Perform a Basic Configuration Check conditions prior to system startup: Step 1 Check that all hardware parts and cables are securely attached to the chassis. Step 2 Check that port adapter configuration information is available, if needed.
No. LED Label 6 7 LED LED flashes when there is traffic Color Status RJ-45 EN (0/2) RJ-45 enable (0/2) Green In the Power Up state, No, remains the LED is On constantly on STATUS Amber while the system boots — Green when the system is operational In the Power Up state, the LED is On System status No, remains constantly on Step 3 During the boot process, observe the system LEDs. The STATUS LED comes on immediately as amber, then turns to green when the Cisco IOS is booted.
Configure Global Parameters When you first start the setup program, you must configure the global parameters. These parameters are used for controlling system-wide settings. Complete the following steps to enter the global parameters: Step 1 Connect a console terminal to the console port, and then boot the router. The system boots from Flash memory. The following information appears after about 30 seconds.
In the following example, the summary shows a Cisco 7301 router at first-time startup; that is, nothing is configured. Any interface listed with OK? value "NO" does not have a valid configuration Interface ATM1/0 FastEthernet1/0 Step 3 IP-Address unassigned unassigned OK? NO NO Method unset unset Status down down Protocol down down Choose which protocols to support on your interfaces. For Internet Protocol (IP)-only installations, you can accept the default values for most of the questions.
The following sample display includes a continuous listing of all configuration parameters selected in Step 3 through Step 8. Only IP, IPX, and AppleTalk are the selected protocols for this example. Configuring global parameters: Enter host name [Router]: router The enable secret is a one-way cryptographic secret password used instead of the enable password when it exists.
Change the Media Type of the Native Gigabit Ethernet SFP GBIC or RJ-45 Ports To be able to use a particular media port, use Cisco IOS to select the media type. This is done by using the media-type interface command: media-type { gbic | rj45 } Example: interface GigabitEthernet 0/1 media-type rj45 end Configure the Interface Transmission and Speed Modes Step 1 After changing the media type, configure the speed and transmission modes to appropriately match the new interface characteristics.
Debug Cisco IOS provides two commands to provide information on your interfaces: show interface GigabitEthernet 0/X (where X is 0, 1, or 2) and show controllers GigabitEthernet 0/X (where X is 0, 1, or 2). The output of the show interface command is useful for determining the current operating mode of the interface (speed/duplex/media-type) and the current interface statistics. The output of the show controller command displays more information specific to the Cisco 7301 router Gigabit Ethernet interface.
Step 3 If you are using AppleTalk on the interface, enter yes. Enter yes to configure for extended AppleTalk networks, and then enter the cable range number. Enter the zone name and any other additional zones that are associated with your local zone: Configure AppleTalk on this interface? [no]: yes Extended AppleTalk network? [no]: yes AppleTalk starting cable range [0]: Step 4 Save your settings to NVRAM. See the “Save the Running Configuration to NVRAM” section on page 28.
Configure Synchronous Serial Interfaces Synchronous serial interfaces are configured to allow connection to WANs through a CSU/DSU. In the following example, a synchronous serial interface in slot 1 is configured for a WAN connection using IP.
The following configuration command script was created: hostname Router enable secret 5 $1$u8z3$PMYY8em./8sszhzk78p/Y0 enable password betty line vty 0 4 password fred snmp-server community public ! ip routing no vines routing ipx routing appletalk routing no apollo routing no decnet routing no xns routing no clns routing no bridge 1 ! Turn off IPX to prevent network conflicts. interface ATM1/0 ip address 1.1.1.10 255.0.0.1 appletalk cable-range 0-0 0.0 appletalk discovery ! router igrp 15 network 1.0.0.
Save the running configuration to NVRAM. See the “Save the Running Configuration to NVRAM” section on page 28. If you do not save the configuration settings that you created in the router using configuration mode and the setup facility, your configuration will be lost the next time you reload the router.
8 After Installation Follow the instructions in this section to replace options after installation. Use the installation and removal information in this section to power off the router, remove the cover, replace the option, replace the cover, and power on the router. Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Insert the CompactFlash Disk into the CompactFlash Disk slot with the label with the vendor name and memory size facing up. The CompactFlash Disk protrudes when completely inserted. Only the CompactFlash Disk is supported in a Cisco 7301 router. Other types of Flash Disks are not supported. Note • The larger the CompactFlash Disk size, the longer the system boot time. • The CompactFlash Disk supports online insertion and removal (OIR).
Step 2 Remove the port adapter from the chassis slot. Use a Phillips screwdriver to turn the screw holding the port adapter latch. The screw should be loose enough to allow the latch to rotate to an unlocked position (1). The latch can rotate 360o. Step 3 Grasp the handle and pull the port adapter (2) or blank port adapter from the router. Step 4 Disconnect all cables from the port adapter. Step 5 Locate the port adapter slot guides inside the Cisco 7301 router.
Step 4 Turn the Cisco 7301 so that the back is facing you. Step 5 Using a Phillips screwdriver, loosen the three captive installation screws holding the cover to the chassis. Step 6 Pull the cover away from the front of the router and lift off the cover. Remove and Install the SODIMMs Follow these steps to remove and install the SDRAM SODIMM. Removing and Replacing the SODIMM 2 1 1 2 80750 Figure 22 SODIMM 2 SODIMM spring latches Note Both SODIMMs must be of the same size and type.
Replace the Cover and Power On the Router Caution The DC return connection to this system is to remain isolated from the system frame and chassis (DC-I). Figure 23 Replacing the Cover 1 80905 2 1 Insert cover under router lip 2 Captive installation screws Step 1 Slide the cover under the lip on the top of the router and insert the tabs into their slots. Step 2 Use a Phillips screwdriver to tighten the captive installation screws.
For S1 or S2 service requests or if you do not have Internet access, contact the Cisco TAC by telephone. (S1 or S2 service requests are those in which your production network is down or severely degraded.) Cisco TAC engineers are assigned immediately to S1 and S2 service requests to help keep your business operations running smoothly.
