Quick Start Guide Cisco 7301 Router 1 Documentation and Resources 2 Prepare for Installation 3 Install External Options 4 Rack-Mount the Router 5 Connect the Router to the Network 6 Start the System 7 Configure the Router 8 After Installation 9 Obtaining Technical Assistance
1 Documentation and Resources Documentation for the Cisco 7301 router is online and orderable. For detailed hardware installation instructions, refer to the online Cisco 7301 Installation and Configuration Guide. Refer to the following online documents for titles and links to related documentation for installation and replacement of parts (including port adapters), regulatory compliance information, and troubleshooting information and tools.
http://www.cisco.com/en/US/partner/ordering/index.shtml • Nonregistered Cisco.com users can order documentation through a local account representative by calling Cisco Systems Corporate Headquarters (California, USA) at 408 526-7208 or, elsewhere in North America, by calling 800 553-NETS (6387). Documentation Feedback You can submit e-mail comments about technical documentation to bug-doc@cisco.com.
2 Prepare for Installation This section contains information about tools and parts, warnings, site preparation information, and information for workbench or tabletop installation and rack-mount installation. Warning Only trained and qualified personnel should install, replace, or service this equipment. Warning Read the installation instructions before you connect the system to its power source. Warning This unit is intended for installation in restricted access areas.
• The rack-mount and cable-management kit: – Two rack-mount brackets and one cable-management bracket – Screws: Four 12-24 x 0.5-inch screws, four 8-18 x .37-inch screws for use with a 19-inch rack, four 8 x .
3 Install External Options This section provides installation instructions for the Gigabit Ethernet SFP Gigabit Interface Converter (GBIC) module. It does not ship installed.
• The native fiber optical Gigabit Ethernet ports and the RJ-45 Gigabit Ethernet ports are reported as GigabitEthernet 0/0, GigabitEthernet 0/1, and GigabitEthernet 0/2 in software. You must use the media-type command to select which media type you want to use before you configure these ports. See page 24.
4 Rack-Mount the Router This section provides information for rack-mounting the router.
Attach the Rack-Mount Brackets—Chassis Rear-Mounted Figure 5 EN AB LE Attaching the Rack-Mount Brackets to the Rear of the Chassis 2 D S IER LL R RM CE CAR LA RX RX RX A ATM SLOT 1 GIGABIT ETHER NET RJ45 EN 0/0 LINK TX GBIC GIGABIT ETHER NET RX RJ45 EN 0/1 LINK TX GBIC GIGABIT ETHER NET RX RJ45 EN 0/2 LINK TX GBIC AUX CONSOLE RX CISCO 7301 ALARM 100-24 0V, 2A, 50/60 Hz 24V=9 A, 48 - 60V=5 A STATUS 1 1 2 Rack-mount bracket 80907 A B COMPACT FLASH 4 screws, 8-18 x .37 in.
Step 1 Align the cable-management bracket (1) to the rack-mount bracket on the left side of the Cisco 7301 router. Step 2 Using a Phillips screwdriver and the M4 x 20-mm screw (2), thread and tighten the screw to the cable-management bracket. Go to the “Four-Post Rack Installation” section on page 10 or the “Two-Post Rack Installation” section on page 11.
Two-Post Rack Installation Figure 8 Installing the Cisco 7301 Router in a Two-Post Rack 1 D LE AB EN R LS RIE M CEL CAR AR RX RX RX AL ATM GIGABIT ETHERNE T 0/0 2 LINK TX GBIC GIGABIT ETHERNE T 0/1 RX RJ45 EN LINK TX GBIC GIGABIT ETHERNE T 0/2 RX RJ45 EN LINK TX GBIC AUX CONSOLE RX ALARM COMPACT FLASH 100-240V , 2A, 50/60 Hz 24V=9A, 48 - 60V=5A 80909 CISCO 7301 STATUS B RJ45 EN A SLOT 1 1 Two-post rack 2 Screw hole for cable-management bracket 3 3 Four 12-24 x 0.
Chassis Ground Connection Installation Warning This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal use. Figure 9 Attaching the Grounding Lug and Wire to the Chassis 3 2 50536 4 1 1 Chassis ground connector 3 Screws 2 Grounding lug 4 Wire Note The grounding lug and Phillips screws are not available from Cisco Systems. Get the grounding lug from an electrical-connector vendor and the screws from a hardware vendor.
5 Connect the Router to the Network This section provides information about cables and ports and attaching the router to the network.
Figure 11 1 Gigabit Ethernet SFP GBIC and RJ-45 Port Identification 2 GIGABIT ETH ERNET 0/0 RJ45 EN LINK TX GBIC 3 RX 4 GIGABIT ETH ERNET 0/1 RJ45 EN LINK TX GBIC 5 6 GIGABIT ETH ERNET 0/2 RX RJ45 EN LINK TX GBIC RX AUX CONSOLE CISCO 73 01 80274 CO FL 1 Gigabit Ethernet RJ-45 port 0/0 4 Gigabit Ethernet SFP GBIC port 0/1 2 Gigabit Ethernet SFP GBIC port 0/0 5 Gigabit Ethernet RJ-45 port 0/2 3 Gigabit Ethernet RJ-45 port 0/1 6 Gigabit Ethernet SFP GBIC port 0/2 Intra-Building
B ecause invisible laser radiation may be emitted from the aperture of the port when no fiber cable is connected, Warning avoid exposure to laser radiation and do not stare into open apertures. Warning Class 1 laser product. Warning Class 1 LED product.
Attach the Mode-Conditioning Patch Cord Figure 13 Attaching the Mode-Conditioning Patch Cord 4 1 // 2 // Offset 7 // TX RX 3 5 6 7 4 84159 8 1 Gray color identifier 5 Single-mode bar 2 To GE interface 6 Offset 3 Blue color identifier 7 Beige color identifier 4 Multimode bar 8 To cable plant Step 1 Attach the patch cord to the LC-type connector on the SFP GBIC modules (2).
Alarm Port Connection Figure 14 Connecting the Alarm Port Cable 1 CONSOLE ALARM 80279 COMPACT FLASH STATUS 1 Alarm port Connect the dry relay alarm port cable connector to the alarm port. It cannot be inserted incorrectly. The dry relay alarm port operates up to 50V AC/DC maximum and up to 80 mA maximum. Total power dissipation should not exceed 300 milliwatts. The normally closed position will have from 15 to 30 ohms resistance. The open position will be greater than 1 megohm.
6 Start the System Connect Power to the Router This section provides instructions for attaching the power cables to the router and powering on the router. Warning This unit might have more than one power cord. To reduce the risk of electric shock, disconnect the two power supply cords before servicing the unit. Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A U.S.
Connect DC-Input Power The color coding of the DC-input power supply leads depends on the color coding of the DC power source at your site. Match the lead color coding for the DC-input power supply to the lead color coding used at the DC power source. Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that a Listed and Certified fuse or circuit breaker no larger than 60 VDC, 15 A is used on all currently-carrying conductors.
Observe the System Startup and Perform a Basic Configuration Check conditions prior to system startup: Step 1 Check that all hardware parts and cables are securely attached to the chassis. Step 2 Check that port adapter configuration information is available, if needed. Step 3 Check that a CompactFlash Disk is installed. Step 4 Check that the console terminal is turned on. Start the Router Step 1 Place the power switch in the ON (|) position.
7 Configure the Router Before configuring the router, determine whether or not you want to use a management tool such as Cisco Security Device Manager. Cisco Security Device Manager (SDM), version 1.1, is an optional Java-based device-management tool that allows you to configure LAN interfaces, routing, Network Address Translation (NAT), firewalls, Virtual Private Networks (VPNs), and other features without knowledge of the Cisco command-line interface (CLI).
cisco 7301 (NPE-G1) processor (revision A) with 245760K/16384K bytes of memory. Processor board ID 0 SB-1 CPU at 650Mhz, Implementation 1, Rev 0.2, 512KB L2 Cache 1 slot midplane, Version 2.0 Last reset from power-on Bridging software. X.25 software, Version 3.0.0. SuperLAT software (copyright 1990 by Meridian Technology Corp). TN3270 Emulation software. 3 Gigabit Ethernet/IEEE 802.3 interface(s) 509K bytes of non-volatile configuration memory.
Step 5 The Simple Network Management Protocol (SNMP) is the most widely supported open standard for network management. It provides a means to access and set configuration and run-time parameters of routers and communication servers. SNMP defines a set of functions that can be used to monitor and control network elements.
Step 9 Save your settings to NVRAM. See the “Save the Running Configuration to NVRAM” section on page 28. If you do not save the configuration settings that you created in the router using configuration mode and the setup facility, your configuration will be lost the next time you reload the router.
GBIC(1) 1000, auto(2) full, half, auto ------------------------------------------------------- a. If you are using the no negotiation auto command, the speed and duplex should be set to a value other than auto for correct operation. b. The only available speed in this mode is 1000 Mbps; there is no difference whether 1000 or auto is selected. When using the SFP GBIC media, there is also the additional negotiation auto command that is used to enable the IEEE 802.
Note Only one port adapter can be installed in the Cisco 7301 at one time. Following are three examples of three different interfaces that might be used. Configure ATM Interfaces In the following example, an ATM interface in slot 1 is configured for an ATM LAN using IP.
IPX network number [2]: Step 3 If you are using AppleTalk on the interface, enter yes. Enter yes to configure for extended AppleTalk networks, and then enter the cable range number. Enter the zone name and any other additional zones that are associated with your local zone: Configure AppleTalk on this interface? [no]: yes Extended AppleTalk network? [no]: yes AppleTalk starting cable range [0]: Step 4 Save your settings to NVRAM. See the “Save the Running Configuration to NVRAM” section on page 28.
Configure IP on this interface? [yes]: IP address for this interface: 1.1.1.10 Number of bits in subnet field [0]: 0 Class C network is 1.1.1.0, 0 subnet bits; mask is /24 Configure IPX on this interface? [yes]: IPX network number [2]: Configure AppleTalk on this interface? [no]: yes Extended AppleTalk network? [no]: yes AppleTalk starting cable range [0]: The following configuration command script was created: hostname Router enable secret 5 $1$u8z3$PMYY8em.
Check the Running Configuration Settings To check the value of the settings you have entered, enter the show running-config command at the Router# prompt: Router# show running-config To review changes you make to the configuration, use the EXEC mode show startup-config command to display the information stored in NVRAM.
8 After Installation Follow the instructions in this section to replace options after installation. Use the installation and removal information in this section to power off the router, remove the cover, replace the option, replace the cover, and power on the router. Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Insert the CompactFlash Disk into the CompactFlash Disk slot with the label with the vendor name and memory size facing up. The CompactFlash Disk protrudes when completely inserted. Note Only the CompactFlash Disk is supported in a Cisco 7301 router. Other types of Flash Disks are not supported. • The larger the CompactFlash Disk size, the longer the system boot time. • The CompactFlash Disk supports online insertion and removal (OIR).
Step 2 Remove the port adaper from the chassis slot. Use a Phillips screwdriver to turn the screw holding the port adapter latch. The screw should be loose enough to allow the latch to rotate to an unlocked position (1). The latch can rotate 360o. Step 3 Grasp the handle and pull the port adapter (2) or blank port adapter from the router. Step 4 Disconnect all cables from the port adapter. Step 5 Locate the port adapter slot guides inside the Cisco 7301 router.
Step 4 Turn the Cisco 7301 so that the back is facing you. Step 5 Using a Phillips screwdriver, loosen the three captive installation screws holding the cover to the chassis. Step 6 Pull the cover away from the front of the router and lift off the cover. Remove and Install the SODIMMs Follow these steps to remove and install the SDRAM SODIMM. Removing and Replacing the SODIMM 2 1 1 2 80750 Figure 22 SODIMM 2 SODIMM spring latches Note Both SODIMMs must be of the same size and type.
Replace the Cover and Power On the Router Figure 23 Replacing the Cover 1 80905 2 1 Insert cover under router lip 2 Captive installation screws Step 1 Slide the cover under the lip on the top of the router and insert the tabs into their slots. Step 2 Use a Phillips screwdriver to tighten the captive installation screws. Step 3 Insert the power cables into the power receptacles on the router. Step 4 Turn the power switch to the ON position to power on the router.
9 Obtaining Technical Assistance For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, the Cisco Technical Assistance Center (TAC) provides 24-hour-a-day, award-winning technical support services, online and over the phone. Cisco.com features the Cisco TAC website as an online starting point for technical assistance. If you do not hold a valid Cisco service contract, please contact your reseller.
Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 European Headquarters Cisco Systems International BV Haarlerbergpark Haarlerbergweg 13-19 1101 CH Amsterdam The Netherlands www-europe.cisco.com Tel: 31 0 20 357 1000 Fax: 31 0 20 357 1100 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA www.cisco.
