Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
Preface This preface describes the objectives, audience, organization, and conventions of this guide, and describes related documents that have additional information.
Preface Organization This guide is organized into the following chapters and appendix. Chapter Name Description Chapter 1 Chapter 1, “Product Overview” Describes the router models and the hardware features available. Chapter 2 Chapter 2, “Installing the Router” Lists the items shipped with the router, the equipment and tools necessary for installing the router, the safety warnings and guidelines, and the procedures for installing the router.
Preface Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device.
Preface Avvertenza IMPORTANTI ISTRUZIONI SULLA SICUREZZA Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento.
Preface Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16193-07 vii
Preface Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.
Preface Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16193-07 ix
Preface Warning When installing the product, please use the provided or designated connection cables/power cables/AC adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the “UL” shown on the code) for any other electrical devices than products designated by CISCO.
Preface Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. SAVE THESE INSTRUCTIONS.
Preface Related Documentation In addition to the Cisco 860 series, Cisco 880 series, and Cisco 890 series ISR Hardware Installation Guide (this document), the Cisco 860 series, Cisco 880 series, and Cisco 890 series ISR documentation set includes the following documents: • Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers • Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Software Configuration Guide • Software Activation on C
Preface Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0.
Preface Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide xiv OL-16193-07
C H A P T E R 1 Product Overview This chapter provides an overview of the features available for the Cisco 860 series, Cisco 880 series, and Cisco 890 series Integrated Services Routers (ISRs), and contains the following sections: • General Description, page 1-1 • Cisco 860 Series ISRs, page 1-2 • Cisco 860VAE Series ISRs, page 1-3 • Cisco 880 Series ISRs, page 1-5 • Cisco 890 Series ISRs, page 1-15 • Hardware Features, page 1-17 Note For compliance and safety information, see Regulatory Comp
Chapter 1 Product Overview Cisco 860 Series ISRs The Cisco 860 series, Cisco 880 series, and Cisco 890 series ISRs have a desktop form factor with built-in wall-mount features. The Cisco 890 series ISRs also have optional rack-mount features. These ISRs are powered by an external power supply adapter. The various models differ in the WAN interface and features that they support.
Chapter 1 Product Overview Cisco 860VAE Series ISRs Figure 1-2 shows the back panel details of the Cisco 861 wireless (861W) ISR. Nonwireless routers do not have antennas on the back panel. However, the feature locations are similar for all Cisco 860 series routers.
Chapter 1 Table 1-1 Product Overview Interfaces of the Cisco 860VAE Series ISRs Model Interfaces 866VAE 867VAE 866VAE-K9 867VAE-K9 1 VDSL/ADSL over POTS port — x — x 1 VDSL/ADSL over ISDN port x — x — 1. FE = Fast Ethernet 2. GE = Gigabit Ethernet Note The Cisco 866VAE, 867VAE, 866VAE-K9, and 867VAE-K9 routers each have two WAN ports. Only one of the two ports can be active at any given time. IOS Images Table 1-2 describes the IOS images included in Cisco 860VAE series routers.
Chapter 1 Product Overview Figure 1-4 shows the back panel details of the Cisco 866VAE ISR. Figure 1-4 Back Panel of the Cisco 866VAE ISR Cisco 866VAE VDSL/ADSL WAN OVER ISDN GE0 1 2 LAN CONSOLE 12V 2.
Chapter 1 Product Overview Cisco 880 Series ISRs • Integrated 4-port 10/100 Ethernet switch for connecting to the LAN • 10/100 FE, VDSLoPOTS, ADSL over POTS, ADSL over ISDN, DSL Multi-mode (VDSL/ADSLoPOTS, VDSL/ADSLoISDN Cisco VA models only), or G.SHDSL port for connecting to the WAN • Optional embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless AP • Optional 2-port Power over Ethernet (PoE) Note • The Cisco 880 series ISRs can include an optional PoE module that provides power to 802.
Chapter 1 Product Overview Cisco 880 Series ISRs Depending on the router model, the primary WAN port can be G.SHDSL, VDSLoPOTS, VDSL/ADSL over ISDN, VDSL/ADSL over POTS, or 10/100 FE. See the Cisco 880 Series Integrated Services Routers data sheet for the WAN interface that is supported on your router. Figure 1-6 shows the front panel details of the Cisco 880 wireless data router. The USB port and the 3G card slot are located on the front panel.
Chapter 1 Product Overview Cisco 880 Series ISRs 1. BRI = Basic rate interface. 2. Ports 0 and 1 provide PoE with the optional PoE module installed. Caution The primary WAN port is designed for an RJ-45 connector only. Damage to the primary WAN port may occur if a non RJ-45 connector is inserted. Figure 1-8 shows the back panel details of the Cisco 887VA and 886VA-M data router.
Chapter 1 Product Overview Cisco 880 Series ISRs Figure 1-9 shows the back panel details of the Cisco 888W data router. Nonwireless routers do not have antennas on the back panel. However, the feature locations are similar across all Cisco 880 series data routers. Back Panel of the Cisco 888W Data Router 231951 Figure 1-9 1 2 3 4 5 6 7 8 9 10 1 ISDN port—not available on 3G models 6 PoE power connector for optional PoE module1 2 Primary WAN port2—G.
Chapter 1 Product Overview Cisco 880 Series ISRs Cisco 881 SRST and Cisco 888 SRST Figure 1-10, Figure 1-11, and Figure 1-12 show the features available on the Cisco 881 SRST and Cisco 888 SRST routers. The features available vary, depending on the router model. Some features may not be available on your router. Depending on the router model, the primary WAN port can be either G.SHDSL or 10/100 FE.
Chapter 1 Product Overview Cisco 880 Series ISRs Figure 1-11 shows the back panel details of the Cisco 881SRST-W voice router.
Chapter 1 Product Overview Cisco 880 Series ISRs Figure 1-12 shows the back panel details of the Cisco 888SRST-W voice router. Back Panel of the Cisco C888SRST-W Voice 241905 Figure 1-12 2 1 2 6 3 4 5 7 8 9 10 1 Primary WAN port1—G.
Chapter 1 Product Overview Cisco 880 Series ISRs Note Configuring the codec complexity setting to support secure calls uses DSP resources, but does not affect the maximum number of supported calls. Table 1-3 Maximum Number of Supported Calls Flexible Complexity Medium Complexity High Complexity C881-V 9 8 6 C887VA-V 8 8 6 C887VA-V-W 8 8 6 Figure 1-13 shows the front panel details of the Cisco 881-V, Cisco 887VA-V, and Cisco 887VA-V-W.
Chapter 1 Product Overview Cisco 880 Series ISRs Figure 1-14 shows the back panel for the Cisco 887VA-V-W router. The Cisco 887VA-V (nowireless) router does not have the antennas on the back panel.
Chapter 1 Product Overview Cisco 890 Series ISRs 3 Voice ports—four FXS/DID ports and one FXO port.
Chapter 1 Product Overview Cisco 890 Series ISRs Figure 1-16 shows the front panel details of the Cisco 890 wireless router. Front Panel of the Cisco 890 Series Wireless ISR 272367 Figure 1-16 1 1 2 LEDs 2 USB ports Figure 1-17 shows the back panel details of the Cisco 892-W router. Nonwireless routers do not have RP-TNC antennas or connectors on the back panel. Some of the features that are shown may not be available on your router.
Chapter 1 Product Overview Hardware Features 4 Auxiliary port 10 Earth ground connection 5 Console port 11 Kensington security slot 6 8-port 10/100 Ethernet switch 1. The Cisco 890 series ISRs can include an optional PoE module that provides power to 802.3af-compliant devices connected to ethernet ports 0 through 3. If this feature was not configured with the factory order you must order and install it to enable the PoE function. 2.
Chapter 1 Product Overview Hardware Features • Wireless LAN Connectivity • Small Form-Factor Pluggable Port • Feature Summary Kensington Lock A Kensington security slot is located on the router back panel. To secure the router to a desktop or other surface, use the Kensington lockdown equipment. Reset Button The Reset button is used to restore the router to the factory default configuration. To do this, press the reset button within five seconds of powering up the router.
Chapter 1 Product Overview Hardware Features Step 2 Press and hold the reset button until the system status LED begins to flash. Typically, this occurs within five seconds. The router reloads itself after the startup configuration has been replaced with the new customer configuration. LEDs The LEDs are located on the front panel of the router. Table 1-4 • Table 1-4 describes the LEDs for the Cisco 860 series, 880 series, and 890 series ISRs.
Chapter 1 Product Overview Hardware Features Table 1-4 LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued) LED Color WLAN (2.4 GHz) Green Description 860 Series 880 Series 1 On—Radio is connected, SSID is configured, and client Wireless models is associated, but no data is being received or being transmitted.
Chapter 1 Product Overview Hardware Features Table 1-4 LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued) LED Color Description 860 Series 880 Series 890 Series Data BRI B1 Green Blinking—B1 channel is either receiving or sending data, — or data is passing through ISDN channel 1. 887, 888 models Data BRI B2 Green Blinking—B2 channel is receiving or sending data, or data is passing through ISDN channel 2.
Chapter 1 Product Overview Hardware Features Table 1-4 LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued) LED SFP 12 EN SFP S Color Description 860 Series 880 Series 890 Series Off Not present. — — Green Present and enabled. — — 892F models Amber Present with failure. — — Green Blinking—Blinking frequency indicates port speed. — — 892F models 1. SSID = service set identifier. 2. LWAPP = Lightweight Access Point Protocol. 3.
Chapter 1 Product Overview Hardware Features Table 1-5 LED Descriptions for the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and Cisco 867VAE-K9 ISRs (continued) LED Activity Description xDSL Link Green On—DSL WAN Mode is selected and DSL training complete. Blinking—DSL WAN Mode is selected but incomplete DSL Link Up state, such as in-training, or controller “OFF,” or no cable attached to DSL connector. Off—Device is powered off or GE WAN mode is selected. GE ACT Green On—GE WAN interface is up.
Chapter 1 Product Overview Hardware Features Close-up of the BRI and FXS LED Indicators 300149 Figure 1-19 Memory The Cisco 860 series, 880 series, and 890 series routers contain flash memory and main memory. Flash Memory The Cisco 860 series, 880 series, and 890 series ISRs use non-upgradable flash memory storage. The onboard flash memory contains the Cisco IOS software image, the boot flash contains the ROMMON boot code, and a separate non-volatile flash contains the cookie configuration.
Chapter 1 Product Overview Hardware Features Table 1-7 Main onboard memory storage Models Onboard Memory Storage Expandibility Cisco 860 series routers 256 MB Not expandable Cisco 860VAE series routers 256 MB Not expandable Cisco 880 series routers A memory expansion slot accommodates a PC2-4200, 256-MB or 512-MB double data rate 2 (DDR2) SODIMM, for a maximum of 768 MB. 256 MB (expandable to 768 MB) USB Port The Cisco 880 series routers have a single Universal Serial Bus (USB 1.
Chapter 1 Product Overview Hardware Features The Cisco 88xG models come with a 34-mm express card slot ready for use with a commercial 3G card radio. The 3G express card slot is located on the front panel. For a list of supported 3G cards, see the Cisco 880 Series Integrated Services Routers data sheet. Wireless LAN Connectivity The embedded Wi-Fi CERTIFIED™, 802.11a/b/g/n-compliant wireless AP is preinstalled in the router as an optional feature.
Chapter 1 Product Overview Hardware Features Supported Cisco Radio Antennas The Cisco 890 series ISRs come with three removable dipole antennas that can be replaced using the Cisco approved antenna extenders listed in Table 1-9. Cisco supports only the antennas listed in Table 1-9 with the Cisco 890 series dual-band radio module. Note Table 1-9 Cisco Antennas Supported on the Cisco 890 Series ISRs Cisco Part Number Antenna Type Maximum Gain Description AIR-ANTM2050D-R Omnidirectional 2.
Chapter 1 Product Overview Hardware Features Table 1-10 Hardware Features Available in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued) Feature Description 860 Series 880 Series 890 Series FE built-in switch ports Provides connection to 10/100BASE-T (10/100-Mbps) All models Fast Ethernet networks.
Chapter 1 Product Overview Hardware Features Table 1-10 Hardware Features Available in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued) Feature Description 860 Series 880 Series 890 Series Real-time clock (RTC) RTC provides nonvolatile date and time when the router is powered on. The RTC is used for verifying the validity of the Certification Authority stored on the router. It is backed up by a nonreplaceable lithium battery.
Chapter 1 Product Overview Hardware Features Table 1-10 Hardware Features Available in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued) Feature Description BRI voice port SFP19 port 860 Series 880 Series 890 Series The ISDN BRI S/T voice interface provides a client-side — (TE) ISDN S/T physical interface for connection to an NT1 device that terminates an ISDN telephone network.
C H A P T E R 2 Installing the Router This chapter describes the equipment and the procedures for successfully installing the Cisco 860 series, 880 series, and 890 series Integrated Services Routers (ISRs), and contains the following sections: • Equipment, Tools, and Connections, page 2-1 • Installing the Router, page 2-3 For compliance and safety information, see the Regulatory Compliance and Safety Information Roadmap that ships with the router and the Regulatory Compliance and Safety Information fo
Chapter 2 Installing the Router Equipment, Tools, and Connections Items Shipped with your Router Unpack the box and verify that all items listed on the invoice were shipped with the router. Table 2-1 lists the items and their quantities that are shipped with each router model.
Chapter 2 Installing the Router Installing the Router Connections Obtain a broadband or Ethernet connection from your service provider. Ethernet Devices Identify the Ethernet devices that you will connect to the router: hub, servers, and workstations or PCs. Ensure that each device has a network interface card (NIC) for connecting to Ethernet ports.
Chapter 2 Installing the Router Installing the Router Warning Note This unit is intended to be mounted on a wall. Please read the wall mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system. Statement 248 • Do not stack anything on top of the router.
Chapter 2 Installing the Router Installing the Router To attach the radio antennas to your wireless router, follow these steps: Step 1 Manually screw the antennas tight to the RP-TNC connectors on the back of the router. Attaching Antennas to the Router 272486 Figure 2-1 Step 2 Orient the antennas. For optimum wireless performance, the antennas should be perpendicular with respect to the floor. a. If the router is being mounted on a desk, orient the antennas straight up. b.
Chapter 2 Installing the Router Installing the Router Antennas Oriented Vertically Up 274774 Figure 2-2 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 2-6 OL-16193-07
Chapter 2 Installing the Router Installing the Router Antennas Oriented Vertically Down 274775 Figure 2-3 Installing on a Table To install the router on a table or other flat horizontal surface, firmly place the router on a table or other horizontal surface. Keep at least 1 inch (2.5 centimeters) of clear space beside the cooling inlet and exhaust vents. Connect the chassis to a reliable earth ground.
Chapter 2 Installing the Router Installing the Router Tip When choosing a location for wall-mounting the router, consider cable limitations and wall structure. To mount the router on a wall, follow these steps: Step 1 Determine the required distance between mounting holes on the router. Figure 2-4 shows the wall-mount holes located on the underside of the router. Note For most router models, the distance between mounting holes is 8.2 inches (208 mm), as shown in Figure 2-4.
Chapter 2 Installing the Router Installing the Router Figure 2-5 Router Mounted on the Wall 1 1 4 231982 2 3 Step 4 1 Two number-10 wood screws mounted on the 3 wall Horizontal surface on which to place the power adapter 2 Wall-mount holes Distance between the screw head and the wall, 1/8 in. (0.32 cm) 4 Connect the chassis to a reliable earth ground. For the chassis ground connection procedures, see the “Installing the Router Ground Connection” section on page 2-11.
Chapter 2 Installing the Router Installing the Router Installing in a Rack The Cisco 890 series ISRs can be mounted in a rack. To install a Cisco 890 series ISR in a rack, follow these steps: Step 1 Remove the screws shown in Figure 2-6. Figure 2-6 Screw Location 278159 1 1 1 Step 2 Caution Screws Using the screws provided, attach the rack-mount brackets to the Cisco 890 series ISR chassis as shown in Figure 2-7. Use two screws on each side.
Chapter 2 Installing the Router Installing the Router Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety: -- This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
Chapter 2 Installing the Router Installing the Router Chassis Ground Connection Using Ring Terminal 231981 Figure 2-8 1 1 Step 4 Ring terminal Connect the other end of the ground wire to a known reliable earth ground point at your site. After you install and properly ground the router, you can connect the power wiring, the WAN and LAN cables, and the cables for administrative access as required for your installation.
C H A P T E R 3 Connecting the Router This chapter describes how to connect Cisco 860 series, Cisco 880 series, and Cisco 890 series Integrated Services Routers (ISRs) to Ethernet devices, Power over Ethernet (PoE), and a network. The chapter contains the following sections: Note • Preparing to Connect the Router, page 3-2 • Connecting a PC, Server, or Workstation, page 3-3 • Connecting a Phone, page 3-4 • Connecting an External Ethernet Switch, page 3-5 • Connecting the V.
Chapter 3 Connecting the Router Preparing to Connect the Router Note The illustrations in this chapter show a wireless router with antennas attached. Nonwireless routers do not have antennas or antenna connectors on the back panel. However, the procedures for connecting devices to the router are the same for both wireless and nonwireless routers. Note Depending on the features available for your router, some content in this chapter may not apply to your router.
Chapter 3 Connecting the Router Connecting a PC, Server, or Workstation Connecting a PC, Server, or Workstation To connect a PC (or other Ethernet devices) to an Ethernet switch port, follow these steps: Step 1 Connect one end of the yellow Ethernet cable to an Ethernet switch port on the router. Figure 3-1 shows a Cisco 888W router connected to a PC.
Chapter 3 Connecting the Router Connecting a Phone Connecting a Phone To connect an 802.3af-compliant phone to an Ethernet switch port, follow these steps: Note A power source must be provided for the phone to function. This can be done in two ways, the phone can be powered via the PoE function using the PoE enabled Ethernet ports or by using an external AC power source connected to the phone. Step 1 Connect one end of the yellow Ethernet cable to Ethernet switch port 0 or port 1 on the router.
Chapter 3 Connecting the Router Connecting an External Ethernet Switch Step 2 Connect the other end of the cable to the RJ-45 port on the phone. Connecting an External Ethernet Switch If more than four PCs in an office must be connected to each other, you can add Ethernet connections to the router by connecting an external Ethernet switch to the Ethernet switch on the router.
Chapter 3 Connecting the Router Connecting the V.92 modem Port Connecting the V.92 modem Port Warning Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end away from the unit first. Statement 1026 For dialup connection to your service provider network through the V.92 port, follow the steps given after Figure 3-4, which show this connection.
Chapter 3 Connecting the Router Connecting a Terminal or PC to the Console Port Connecting a Terminal or PC to the Console Port Connect a terminal or PC to the Console Auxiliary (Aux) port either to configure the software by using the CLI or to troubleshoot problems with the router. To connect a terminal or PC to the console port on the router and access the CLI, follow these steps: Connect the RJ-45 end of a DB-9–to–RJ-45 serial cable to the RJ-45 Console Aux port on the router.
Chapter 3 Connecting the Router Connecting a Modem to the Auxiliary Port Terminal Emulator Settings Use the following settings for the terminal emulator connection: • 9600 baud • 8 data bits, no parity • 1 stop bit • No flow control When the terminal emulator establishes communications, the router prompt is displayed. For more information on terminal emulation settings, see Applying Correct Terminal Emulator Settings for Console Connections.
Chapter 3 Connecting the Router Connecting the 3G Card Step 2 Connect the DB-9 end of the console cable to the DB-9 end of the modem adapter. Step 3 Connect the DB-25 end of the modem adapter to the modem. Step 4 Make sure that your modem and the router auxiliary port are configured for the same transmission speed (up to 115200 bits per second [b/s] is supported) and support mode control with data carrier detect (DCD) and data terminal ready (DTR).
Chapter 3 Connecting the Router Connecting the 3G Card Figure 3-7 Inserting the 3G Card 4 271473 3 2 3 1 6 5 5 1 3G card with the Cisco logo facing up 4 Screw holes for locking bracket 2 3G express card slot 5 Pin holes for aligning the locking bracket 3 Notches on the 3G card 6 SIM slot (in HSPA1 cards only) 1. HSPA = High-Speed Packet Access. Open the top of the anti-theft locking bracket, as shown in Figure 3-8.
Chapter 3 Connecting the Router Connecting the 3G Card Step 3 Slide the opened locking bracket under the 3G card. The locking bracket should align with the notches on either side of the 3G card, as shown in Figure 3-9, and the pins on the locking bracket should be inserted into the corresponding holes in the router.
Chapter 3 Connecting the Router Connecting the 3G Card Step 4 Close the locking bracket, as shown in Figure 3-10. Figure 3-10 Closing the Locking Bracket 1 271580 2 1 Step 5 3G card 2 Locking bracket Insert the screws, as shown in Figure 3-11, and tighten with a number 2 Phillips screwdriver.
Chapter 3 Connecting the Router Connecting the 3G Card Note The antenna connector receptacle may be located on the left, right, or front of the 3G card, depending on your card. Figure 3-12 shows the antenna connected to the 3G card with an SSMB type plug, and Figure 3-13 shows the antenna with the SMK-TS-9 connector. Figure 3-12 Antenna connected to the 3G Card with SSMB connector 272653 1 3 2 1 Antenna on a cradle 2 Antenna SSMB connector 3 Antenna connector receptacle1 1.
Chapter 3 Connecting the Router Connecting the 3G Card Antenna with the SMK-TS- 9 Connector 279085 Figure 3-13 Original antenna assembly SMK-TS-9 connector Cable If you are using an extension cable, you must attach the 3G adapter for extended cable antenna to the body of the router. Depending on the SKU ordered, the adapters come with different connectors. Table 3-1 lists the different adapters and SKUs supported by each adapter.
Chapter 3 Connecting the Router Installing the 3G Adapter for Extended Cable/Antenna Step 8 Remove the protective tape from the adhesive on the bottom of the antenna cradle, then firmly press the cradle to the flat surface.
Chapter 3 Connecting the Router Installing the 3G Adapter for Extended Cable/Antenna Step 2 Locate the hooks on the adapter as shown in Figure 3-15. Figure 3-15 Locating the Hooks on the Adapter 279122 1 1 Step 3 Hooks on the adapter Align and insert the hooks of the adapter into the air vent holes on the left side router body as shown in Figure 3-16. Figure 3-16 Inserting the Hooks 1 1 279123 1 Hooks aligned and inserted into the router.
Chapter 3 Connecting the Router Installing the 3G Adapter for Extended Cable/Antenna Step 4 Align the circular adapter hole with the hole on the router chassis from where you removed the screw in Step 1 and use the screw to attach the adapter to the router as shown in Figure 3-17.
Chapter 3 Connecting the Router Installing the 3G Adapter for Extended Cable/Antenna Step 5 Connect the extension cable to the 3G card as described in the “Connecting the 3G Card” section on page 3-9. The complete assembly is shown in Figure 3-18.
Chapter 3 Connecting the Router Connecting a Data BRI Port Table 3-2 Cisco Adapter Cables for Use with 3G Fixed Routers Cisco Product Number Antenna Adapter Length Insertion Loss Frequency (MHz) 3G-ACC-SSMB-TNC 14.5 inches 0.66 dB 2100 3G-ACC-TS9-TNC 13.5 inches 0.62 dB 2100 For additional information on all the available cables and antennas available for 3G, go to: http://www.cisco.com/en/US/docs/routers/access/1800/1861/software/feature/guide/mrwlsgsm.
Chapter 3 Connecting the Router Connecting a Data BRI Port Although the following procedure shows a Cisco 888W data router, this procedure applies to all Cisco 880 series router with a Data BRI port. To connect the Data BRI port to the ISDN service provider, follow these steps: Step 1 Connect one end of the orange ISDN S/T cable to the Data BRI port on the router. Figure 3-19 shows a Data BRI connection.
Chapter 3 Connecting the Router Connecting an FE Line to an FE WAN Port Connecting an FE Line to an FE WAN Port To connect the Fast Ethernet (FE) WAN port on the router, follow these steps: Step 1 Connect one end of the yellow cable to the FE WAN port as shown in Figure 3-20. Figure 3-20 Connecting the FE WAN Port 1 231992 WAN FE 4 1 2 3 Internet Step 2 1 FE WAN port 2 CAT 5 cable 3 Modem connected to the Internet Connect the other end of cable to an available port on the modem.
Chapter 3 Connecting the Router Connecting an GE Line to an GE WAN Port Connecting an GE Line to an GE WAN Port To connect the Gigabit Ethernet (GE) WAN port on the router, follow these steps: Step 1 Connect one end of the yellow cable to the GE WAN port as shown in Figure 3-21. Connecting the GE WAN Port 274493 Figure 3-21 1 2 3 Internet Step 2 1 GE WAN port 2 CAT 5 cable 3 Modem connected to the Internet Connect the other end of cable to an available port on the modem.
Chapter 3 Connecting the Router Connecting an xDSL Line Connecting an xDSL Line Warning Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end away from the unit first. Statement 1026 Caution Cisco Systems DSL WAN Interfaces are tested for compliance with regulatory standards such as FCC Part 68, ITU-T K.21, IEC 61000-4-5, and CSA/EN/IEC/UL 60950-1.
Chapter 3 Connecting the Router Connecting an xDSL Line Figure 3-22 Primary Protection Device Location Telecom Service Overhead Service Entrance Home or Business Router Service Utilities Entrance or Demarcation Point Network Interface Box/ Network Interface Device/ Station Protector Note: Primary Protection may be located Outside or Inside of Premise Building Ground Rod connected to Service entrance and Primary Protection 281392 * Alternative Underground Service Entrance To connect the router to
Chapter 3 Connecting the Router Connecting Power over Ethernet Caution The primary WAN port is designed for an RJ-45 connector only. Damage to the primary WAN port may occur if a non RJ-45 connector is inserted The DSL line must be provisioned by your service provider and correctly configured so that the LED shows the carrier detect (CD) status. On Cisco 860VAE routers, check the DSL Link LED. Note Connecting Power over Ethernet Warning This unit might have more than one power supply connection.
Chapter 3 Connecting the Router Connecting the AC Adapter Figure 3-24 Connecting PoE 1 4 5 3 2 2 6 1 48-VDC PoE input jack 4 AC plug 2 Power cord 5 12-VDC input power-jack plug 3 Power adapter—48 VDC 6 Power adapter—12 VDC 231995 4 Connecting the AC Adapter Warning The device is designed to work with TN power systems. Statement 19 Warning This product relies on the building’s installation for short-circuit (overcurrent) protection.
Chapter 3 Connecting the Router Connecting the AC Adapter To connect your Cisco 860 series or Cisco 880 series ISR to an AC power outlet, follow these steps: Step 1 Connect the router to an AC power outlet as shown in Figure 3-25.
Chapter 3 Connecting the Router Connecting the AC Adapter Step 2 To secure the power cord to the router, attach the power lock clip to the power cord, slide the clip to the end of the DC plug, and secure the retaining clip into the router chassis. See Figure 3-26.
Chapter 3 Connecting the Router Connecting an FXS Line Snap the latches into the holes on either side of the power connector. See Figure 3-27. Step 3 Figure 3-27 Power Lock Clip Latched Into the Holes on Either Side of the Power Connector 1 4 3 270800 2 1 Power lock clip 3 Power adapter 2 Power cord 4 AC plug Connecting an FXS Line Use a standard straight-through RJ-11 modular telephone cable to connect a Foreign Exchange Service (FXS) port to a telephone or fax machine.
Chapter 3 Connecting the Router Connecting an FXS Line To connect the FXS line, follow these steps: Step 1 Connect one end of the straight-through RJ-11 cable to the FXS port. Figure 3-28 shows an FXS line connection. Figure 3-28 Connecting an FXS Line 1 2 241907 3 Fax machine or telephone Step 2 1 FXS port 2 RJ-11 cable 3 RJ-11 port Connect the other end of the cable to the RJ-11 port on the fax machine or telephone.
Chapter 3 Connecting the Router Connecting an FXO Line Connecting an FXO Line Use a straight-through RJ-11 cable to connect the FXO voice port to the PSTN or PBX through a telephone wall outlet. Warning Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end away from the unit first.
Chapter 3 Connecting the Router Connecting a Voice ISDN BRI Line Note If you have specified the use of a private line automatic ringdown (PLAR) off-premises extension (OPX) connection mode for an FXO voice port (with loop resistance less than 8000 Ohm), you must ensure that the soft-offhook option is enabled on the port.
Chapter 3 Connecting the Router Connecting a Small-form-factor Pluggable Module Figure 3-30 shows a voice BRI line connection. Figure 3-30 Connecting a Voice BRI Line 1 2 241906 3 Step 2 1 Voice BRI port 2 RJ-45 cable 3 Telephone outlet Connect the other end of the cable to the RJ-45 telephone outlet or other device.
Chapter 3 Connecting the Router Connecting a Small-form-factor Pluggable Module • Removing an SFP Module, page 3-35 • Online Insertion and Removal, page 3-36 Safety Warnings Laser Safety Warnings Optical SFPs use a small laser to generate the fiber-optic signal. Keep the optical transmit and receive ports covered whenever a cable is not connected to the port.
Chapter 3 Connecting the Router Connecting a Small-form-factor Pluggable Module Installing an SFP Module 94126 Figure 3-31 Caution Caution Do not remove the optical port plugs from the SFP until you are ready to connect cabling. Connect the network cable to the SFP module. Step 2 Removing an SFP Module Follow these steps to remove the SFP module from a Cisco 892F series router: Disconnect all cables from the SFP.
Chapter 3 Connecting the Router Connecting a Small-form-factor Pluggable Module Figure 3-32 Figure 5-42 Disconnecting SFP Latch Mechanisms 1 2 3 4 A 117722 B Tip Step 3 1 Sliding latch 3 Bale-clasp latch 2 Swing and slide latch 4 Plastic collar latch Use a pen, screwdriver, or other small straight tool to gently release a bale-clasp handle if you cannot reach it with your fingers. Grasp the SFP on both sides and remove it from the router.
Chapter 3 Connecting the Router Verifying Connections Verifying Connections To verify that all devices are properly connected to the router, first turn on all the connected devices, then check the LEDs. To verify router operation, refer to Table 3-3. For full LED description, see Table 1-4 and Table 1-2. Table 3-3 Verifying the Router Operation Power and Link LEDs to Check Normal Patterns Power OK On when power is supplied to the router.
Chapter 3 Connecting the Router Verifying Connections Table 3-3 Verifying the Router Operation (continued) Power and Link LEDs to Check Normal Patterns To wireless LAN WLAN LINK Wireless LAN link status: WLAN 2.4 GHz WLAN 5.0 GHz PoE14 PoE 0 (880 and 890 series only) PoE 1 (880 and 890 series only) • Green if at least one client is associated. • Off if no client is associated. Wireless LAN 2.
Chapter 3 Connecting the Router Verifying Connections Table 3-3 Verifying the Router Operation (continued) Power and Link LEDs to Check Normal Patterns To DSL line (860VAE models only) DSL LINK On when DSL WAN Mode is selected and DSL training complete. Blinking when DSL WAN Mode is selected but incomplete DSL LinkUp state such as in-training (slow initially, fast when almost be connected), or controller "OFF", or no cable attached to DSL connector.
Chapter 3 Connecting the Router Verifying Connections Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-40 OL-16193-07
C H A P T E R 4 Initial Configuration This chapter provides instructions for initial configuration of the Cisco 860 series, 880 series, and 890 series Integrated Services Routers (ISRs). For the initial configuration, we recommend using Cisco Configuration Professional (CP) Express. Cisco CP Express is a web-based graphical user interface that guides you through initial configuration.
Chapter 4 Initial Configuration Cisco IOS CLI To configure the initial router settings using the Cisco IOS CLI, follow these steps: Step 1 Set up a console connection to your router. The following message is displayed: ... router con0 is now available Step 2 Press Return. The following message is displayed: Cisco Configuration Professional Express (Cisco CP Express) is installed on this device. This feature requires the one-time use of the username "username1" with the password "password1.
Chapter 4 Initial Configuration Setup Command Facility Note Step 7 Save your configuration changes regularly to avoid losing them during resets, power cycles, or power outages. Use the copy running-config startup-config command at the privileged EXEC mode prompt (Router#) to save the configuration to NVRAM. Verify the initial configuration. See the “Verifying the Initial Configuration” section on page 4-5.
Chapter 4 Initial Configuration Setup Command Facility Step 4 When the following messages appear, enter yes to enter basic management setup. At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'.
Chapter 4 Initial Configuration Verifying the Initial Configuration hostname Router enable secret 5 $1$D5P6$PYx41/lQIASK.HcSbfO5q1 enable password xxxxxx line vty 0 4 password xxxxxx snmp-server community public ! no ip routing ! interface FastEthernet4 no shutdown speed 100 duplex auto ip address 172.1.2.3 255.255.0.0 ! Step 12 Respond to the following prompts. Enter 2 to save the initial configuration. [0] Go to the IOS command prompt without saving this config.
Chapter 4 Initial Configuration Initial Configuration of the Wireless Access Point Initial Configuration of the Wireless Access Point The embedded wireless access point (AP) runs its own IOS.
A P P E N D I X A Technical Specifications This appendix provides router, port, and cabling specifications for the Cisco 860 series, Cisco 880 series, and Cisco 890 series Integrated Services Routers (ISRs).
Appendix A Technical Specifications Router Specifications Router Specifications Table A-1 lists the system specifications for the routers. Table A-1 Router Specifications Design Specification (all models except Cisco 860VAE series) Design Specification Cisco 860VAE series Dimensions with antenna and rubber feet (H x W x D) 1.9 x 12.8 x 10.4 in. 1.75 x 9.5 x 9 in. Weight (not including desktop power supply) 5.5 lb (2.5 kg), maximum 3 lb (1.
Appendix A Technical Specifications Wireless Access Point Wireless Access Point Table A-2 lists the specifications for the wireless access point (AP). Table A-2 Wireless Access Point Specifications Description Design Specification Radio technology IEEE 802.11n draft 2.0 standard compliant. 2x3 MIMO1 radio. Backward compatible with 802.11b/g and 802.11a (Cisco 890 series routers). Operating frequency Cisco 860 series and 880 series ISRs 2.4-GHz radio band Cisco 890 series ISRs 2.
Appendix A Technical Specifications Console and Auxiliary Port Connector Pinouts 1. RX = Receive 2. TX = Transmit Table A-4 describes the RJ-45 connector pinouts for the Gigabit Ethernet (GE) ports of the Cisco 860VAE and 860VAE-K9 ISRs. Table A-4 Ethernet GE Port Pinouts Pin GE Signal (LAN and WAN) 1 Tx A+1 2 Tx A- 3 Rx B+2 4 Tx C+ 5 Tx C- 6 Rx B- 7 Rx D+ 8 Rx D- 1. TX = Transmit 2.
Appendix A Technical Specifications FXS and FXO Port Connector Pinouts FXS and FXO Port Connector Pinouts Table A-7 lists the FXS and FXO connector pinouts. Table A-6 FXS and FXO Connector Pinouts (RJ-11-to-RJ-45) Pin Signal 1 NC 2 NC 3 TIP 4 RING 5 NC 6 NC VDSL2 Port Connector Pinouts Table A-7 lists the VDSL2 connector pinouts.
Appendix A Technical Specifications V.92 Port Connector Pinouts V.92 Port Connector Pinouts Table A-9 lists the V.92 connector pinouts. Table A-9 V.92 Connector Pinouts (RJ-11-to-RJ-45) RJ-11 Pin Function 1 Unused 2 Unused 3 TIP 4 RING 5 Unused 6 Unused G.SHDSL Port Connector Pinouts Table A-10 lists the pinouts for the symmetrical high-speed DSL (G.SHDSL) WAN port for two-pair products, including the following router model(s): • C888 Table A-10 G.
Appendix A Technical Specifications Data BRI Port Connector Pinouts Table A-11 G.SHDSL WAN Port Pinouts (continued)for Four-Pair Products Pin Function 4 TIP (Port0) 5 RING (Port0) 6 RING (Port2) 7 TIP (Port3) 8 RING (Port3) Data BRI Port Connector Pinouts Table A-12 lists the pinouts for the Data BRI port.
Appendix A Technical Specifications SFP Port Connector Pinouts SFP Port Connector Pinouts Table A-14 lists the pinouts for the SFP port.
Appendix A Technical Specifications Cable Specifications Ethernet Cable Specifications Table A-15 lists the specifications that apply to both straight-through and crossover Ethernet cables. Table A-15 Ethernet Cable Specifications Type Category 10BASE-T Category 3 or 5 100BASE-T Category 5 or higher 1000BASE-T Category 5 or higher Maximum Cable Length The maximum length for the Ethernet cables that connect equipment to the router is 328 feet (100 meters).
Appendix A Technical Specifications Cable Specifications Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide A-10 OL-16193-07
