A P PEN D I X C Cabling Specifications for the Universal Access Server This appendix provides the following pinout information: • • • • • • Console and Auxiliary Port Signals and Pinouts Ethernet Cable Assembly and Pinouts Dual T1/PRI Card Port Pinouts Dual E1 or T1/PRI Card Cable Assemblies and Pinouts Synchronous Serial Cable Assemblies and Pinouts Alarm Port Pinouts Note The tables in this appendix specify pinouts only for the pins used. Pins not listed are not used.
Console and Auxiliary Port Signals and Pinouts • • RJ-45-to-DB-25 female DTE adapter (labeled Terminal). RJ-45-to-DB-25 male DCE adapter (labeled Modem). For console connections, proceed to the section “Console Port Signals and Pinouts” later in this appendix; for modem connections, proceed to the section “Auxiliary Port Signals and Pinouts” later in this appendix. Identifying a Rollover Cable You can identify a rollover cable by comparing the two modular ends of the cable.
Console and Auxiliary Port Signals and Pinouts Console Port Signals and Pinouts Use the RJ-45-to-RJ-45 rollover cable and RJ-45-to-DB-9 female DTE adapter (labeled Terminal) to connect the console port to a PC running terminal emulation software. Figure C-2 shows how to connect the console port to a PC. Table C-1 lists the pinouts for the asynchronous serial console port, the RJ-45-to-RJ-45 rollover cable, and the RJ-45-to-DB-9 female DTE adapter (labeled Terminal).
Console and Auxiliary Port Signals and Pinouts Use the RJ-45-to-RJ-45 rollover cable and RJ-45-to-DB-25 female DTE adapter (labeled Terminal) to connect the console port to a terminal. Figure C-3 shows how to connect the console port to a terminal. Table C-2 lists the pinouts for the asynchronous serial console port, the RJ-45-to-RJ-45 rollover cable, and the RJ-45-to-DB-25 female DTE adapter (labeled Terminal).
Console and Auxiliary Port Signals and Pinouts Auxiliary Port Signals and Pinouts Use the RJ-45-to-RJ-45 rollover cable and RJ-45-to-DB-25 male DCE adapter (labeled Modem) to connect the auxiliary port to a modem. Figure C-4 shows how to connect the auxiliary port to a modem. Table C-3 lists the pinouts for the asynchronous serial auxiliary port, the RJ-45-to-RJ-45 rollover cable, and the RJ-45-to-DB-25 male DCE adapter (labeled Modem).
Ethernet Cable Assembly and Pinouts Ethernet Cable Assembly and Pinouts This section describes the pinouts for the Ethernet ports and cables. Figure C-5 shows an Ethernet attachment unit interface (AUI) cable assembly, and Table C-4 lists the AUI cable pinouts.
Dual T1/PRI Card Port Pinouts Table C-4 Ethernet (AUI) Cable Pinouts (DB-15) (Continued) Pin Ethernet Circuit Signal 14 VS Voltage Shield (L25 and M25) Shell PG Protective Ground Dual T1/PRI Card Port Pinouts Table C-5 lists the dual T1/PRI card port pinouts. Use a straight-through RJ-48C-to-RJ-48C cable to connect the T1 port to an RJ-48C jack.
Dual E1 or T1/PRI Card Cable Assemblies and Pinouts Dual E1 or T1/PRI Card Cable Assemblies and Pinouts Table C-6 lists the six serial cables available from Cisco Systems for connecting the E1 or T1/PRI card ports.
Dual E1 or T1/PRI Card Cable Assemblies and Pinouts E1 Interface Cable for 120-Ohm, Balanced Connections (with DB-15 Connector) Figure C-8 E1 Interface Cable for 120-Ohm, Balanced Connections (with Twinax Connectors) Figure C-9 E1 Interface Cable for 120-Ohm, Balanced Connections (with RJ-48C Connector) Table C-7 EI Interface Cable Pinouts H2422 H2424 H2476 Figure C-7 CE1 End Network End DB-151 BNC DB-15 RJ-452 Twinax RJ-45/NT3 Pin Signal4 Signal Pin Signal Pin Signal Pin Signal
Synchronous Serial Cable Assemblies and Pinouts Table C-7 CE1 End EI Interface Cable Pinouts (Continued) Network End 1 BNC DB-15 Pin Signal4 Signal Pin Signal Pin Signal Pin Signal Pin Signal 7 RX Shield – 2 TX Shield Shiel d TX Shield 6 RX Shield 3 TX Shield 9 TX Tip RX Tip 3 RX Tip RX-1 RX Tip 1 TX Tip 4 RX Tip 2 TX Ring RX Shield 11 RX Ring RX-2 RX Ring 2 TX Ring 5 RX Ring 10 TX Shield – 4 RX Shield Shiel d RX Shield 3 TX Shield 6 RX Shield DB
Synchronous Serial Cable Assemblies and Pinouts Figure C-10 EIA-530 Serial Cable Assembly -46 -45 -16 -15 60-pin connector (J1) 25-pin connector (J2) H1972 J2-13 J2-25 J2-14 J2-1 J1-1 -30 -31 -60 Connectors are not to scale.
Synchronous Serial Cable Assemblies and Pinouts Table C-8 EIA-530 DTE Cable Pinouts (DB-60 to DB-25) (Continued) 60 Pin Signal 25 Pin Signal Direction DTE DCE1 J1-5 J1-6 DCD/DCD+ DCD/DCD– J2-8 J2-10 CF(A), DCD+ CF(B), DCD– <— <— J1-24 J1-23 TxC/RxC+ TxC/RxC– J2-15 J2-12 DB(A), TxC+ DB(B), TxC– <— <— J1-26 J1-25 RxC/TxCE+ RxC/TxCE– J2-17 J2-9 DD(A), RxC+ DD(B), RxC– <— <— J1-44 J1-45 LL/DCD Circuit_GND J2-18 J2-7 LL Circuit_ GND —> – J1-7 J1-8 DTR/DSR+ DTR/DSR– J2-20 J2-23 CD(A
Synchronous Serial Cable Assemblies and Pinouts Figure C-11 EIA/TIA-232 Cable Assembly 1-46 1-45 1-16 1-15 60-pin connector (J1) 25-pin connector (J2) H1972 J2-13 J2-25 J2-14 J2-1 J1-1 1-30 1-31 1-60 Table C-9 Connectors are not to scale. EIA/TIA-232 DTE Cable Pinouts (DB-60 to DB-25) 60 Pin Signal Description Direction 25 Pin Signal J1-50 J1-51 J1-52 MODE_0 GND MODE_DCE Shorting group – – – J1-46 Shield GND Single – J2-1 Shield GND J1-41 Shield TxD/RxD – Twisted pair no.
Synchronous Serial Cable Assemblies and Pinouts Table C-9 EIA/TIA-232 DTE Cable Pinouts (DB-60 to DB-25) (Continued) 60 Pin Signal Description Direction 25 Pin Signal J1-33 Shield DCD/LL – Twisted pair no. 12 <— – J2-8 Shield DCD – J1-37 Shield TxC/NIL – Twisted pair no. 8 <— – J2-15 Shield TxC – J1-38 Shield RxC/TxCE – Twisted pair no. 7 <— – J2-17 Shield RxC – J1-44 Shield LL/DCD – Twisted pair no. 2 —> – J2-18 Shield LTST – J1-43 Shield DTR/DSR – Twisted pair no.
Synchronous Serial Cable Assemblies and Pinouts Table C-10 EIA/TIA-232 DCE Cable Pinouts (DB-60 to DB-25) (Continued) 60 Pin Signal Description Direction 25 Pin Signal J1-45 Shield Circuit GND – Twisted pair no. 1 – – J2-7 Shield Circuit GND J1-44 Shield LL/DCD – Twisted pair no. 2 —> – J2-8 Shield DCD – J1-39 Shield TxCE/TxC – Twisted pair no. 7 —> – J2-15 Shield TxC – J1-40 Shield NIL/RxC – Twisted pair no. 6 —> – J2-17 Shield RxC – J1-33 Shield DCD/LL – Twisted pair no.
Synchronous Serial Cable Assemblies and Pinouts Figure C-12 EIA/TIA-449 Cable Assembly 60-pin connector (J1) 37-pin connector (J2) J2-19 J2-37 H1973 -46 -45 -16 -15 J1-1 -30 -31 -60 J2-20 J2-1 Connectors are not to scale.
Synchronous Serial Cable Assemblies and Pinouts Table C-11 EIA/TIA-449 DTE Cable Pinouts (DB-60 to DB-37) (Continued) 60 Pin Signal Description Direction 37 Pin Signal J1-1 J1-2 CTS/RTS+ CTS/RTS– Twisted pair no. 1 <— <— J2-9 J2-27 CS+ CS– J1-44 J1-45 LL/DCD Circuit_GND Twisted pair no. 12 —> _ J2-10 J2-37 LL SC J1-3 J1-4 DSR/DTR+ DSR/DTR– Twisted pair no. 2 <— <— J2-11 J2-29 DM+ DM– J1-7 J1-8 DTR/DSR+ DTR/DSR– Twisted pair no.
Synchronous Serial Cable Assemblies and Pinouts Table C-12 EIA/TIA-449 DCE Cable Pinouts (DB-60 to DB-37) (Continued) 60 Pin Signal Description Direction 37 Pin Signal J1-24 J1-23 TxC/RxC+ TxC/RxC– Twisted pair no. 9 —> —> J2-8 J2-26 RT+ RT– J1-9 J1-10 RTS/CTS+ RTS/CTS– Twisted pair no. 5 —> —> J2-9 J2-27 CS+ CS– J1-29 J1-30 NIL/LL Circuit_GND Twisted pair no. 12 —> – J2-10 J2-37 LL SC J1-7 J1-8 DTR/DSR+ DTR/DSR– Twisted pair no.
Synchronous Serial Cable Assemblies and Pinouts V.35 Cable Assembly 60-pin connector (J1) -46 -45 -16 -15 J1-1 -30 -31 -60 Table C-13 34-pin connector (J2) J2-B J2-D J2-A J2-C J2-KK J2-MM J2-LL J2-NN Connectors are not to scale. H1975 Figure C-13 V.
Synchronous Serial Cable Assemblies and Pinouts Table C-13 V.35 DTE Cable Pinouts (DB-60 to 34-Pin) (Continued) 60 Pin Signal Description Direction 34 Pin Signal J1-34 Shield DSR/DTR – Twisted pair no. 7 <— – J2-E Shield DSR – J1-33 Shield DCD/LL – Twisted pair no. 6 <— – J2-F Shield RLSD – J1-43 Shield DTR/DSR – Twisted pair no. 10 —> – J2-H Shield DTR – J1-44 Shield LL/DCD – Twisted pair no. 11 —> – J2-K Shield LT – J1-18 J1-17 TxD/RxD+ TxD/RxD– Twisted pair no.
Synchronous Serial Cable Assemblies and Pinouts Table C-14 V.35 DCE Cable Pinouts (DB-60 to 34-Pin) (Continued) 60 Pin Signal Description Direction 34 Pin Signal J1-46 Shield_GND Single – J2-A Frame GND J1-45 Shield Circuit_GND – Twisted pair no. 12 – – J2-B Shield Circuit GND – J1-35 Shield CTS/RTS – Twisted pair no. 8 <— – J2-C Shield RTS – J1-42 Shield RTS/CTS – Twisted pair no. 9 —> – J2-D Shield CTS – J1-43 Shield DTR/DSR – Twisted pair no.
Synchronous Serial Cable Assemblies and Pinouts X.21 Figure C-14 shows the X.21 cable assembly. Table C-15 lists the DTE pinouts. Table C-16 lists the DCE pinouts. Arrows indicate signal direction: a right arrow (—>) indicates DTE to DCE, and a left arrow (<—) indicates DCE to DTE. Figure C-14 X.21 Cable Assembly 1-46 1-45 1-16 1-15 60-pin connector (J1) 34-pin connector (J2) H1974 J2-8 J2-15 J1-1 1-30 1-31 1-60 J2-9 J2-1 Connectors are not to scale. Table C-15 X.
Synchronous Serial Cable Assemblies and Pinouts Table C-15 X.21 DTE Cable Pinouts (DB-60 to DB-15) (Continued) 60 Pin Signal Description Direction 15 Pin Signal J1-28 J1-27 RxD/TxD+ RxD/TxD– Twisted pair no. 6 <— <— J2-4 J2-11 Receive+ Receive– J1-1 J1-2 CTS/RTS+ CTS/RTS– Twisted pair no. 1 <— <— J2-5 J2-12 Indication+ Indication– J1-26 J1-25 RxC/TxCE+ RxC/TxCE– Twisted pair no. 5 <— <— J2-6 J2-13 Timing+ Timing– J1-15 Shield Control_GND – Twisted pair no.
Alarm Port Pinouts Alarm Port Pinouts Table C-17 lists the pinouts for the alarm port.
