Technical Specs
Table Of Contents
- Cisco Connected Grid WPAN Module for CGR 1000 Series Installation and Cisco Resilient Mesh Configuration Guide (Cisco IOS)
- Cisco Connected Grid WPAN Module for CGR 1000 Series Installation and Cisco Resilient Mesh Configuration Guide (Cisco IOS)
- Hardware Overview
- WPAN Antennas, Connectors, and Cables
- Installing and Removing the Module
- Technical Specifications
- Information About Cisco Resilient Mesh and WPAN
- Configuring Cisco Resilient Mesh and the WPAN Module
- Configuring the WPAN Interface
- Configuring the CGM WPAN OFDM Module
- Configuring Adaptive Modulation
- Configuring Group Multicast
- Configuring RPL
- Configuring IPv6
- Configuring PON RPL
- Configuring the Power Outage Server
- Configuring QoS
- Configuring Cisco Resilient Mesh Security
- Configuring IPv6 Multicast Agent
- Configuring Dual-PHY WPAN
- Configuring DTLS Relay for EST
- Configuring Wi-SUN Mode
- Verifying Connectivity to the CGR
- show Command Examples
- Debugging the WPAN Module
- Sample Router Configuration
- Sample CGR and ASR Configuration
- Checking and Upgrading the WPAN Firmware Version
- Related Documentation
- Obtaining Documentation and Submitting a Service Request
Cisco Connected Grid WPAN Module for CGR 1000 Series
Installation and Cisco Resilient Mesh Configuration Guide
(Cisco IOS)
This guide explains how to install the IEEE 802.15.4e/g Cisco Connected Grid Wireless Personal Area Network (WPAN) module
and how to configure the Cisco Resilient Mesh (formerly known as CG-Mesh). This guide addresses configuration for a Cisco 1000
Series Connected Grid Router (CGR 1000) installed with Cisco IOS software.
For detailed information of the WPAN-OFDM module, see Connected Grid Module (CGM) WPAN-OFDM Module - Cisco
IOS.
Note
Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030
Danger
The Cisco Connected Grid WPAN Module is installed in either of the CGR 1000 series models: Cisco 1120 Connected Grid
Router (CGR 1120) or Cisco 1240 Connected Grid Router (CGR 1240). The WPAN module is installed at the factory. Only
technicians of Cisco or Cisco partners may install, uninstall, or configure Connected Grid modules.
Note
For system requirements, important notes, limitations, open and resolved bugs, and last-minute documentation updates, see the Release
Notes for CGR 1000 (Cisco IOS) on Cisco.com:
http://www.cisco.com/c/en/us/support/routers/1000-series-connected-grid-routers/products-release-notes-list.html.
For translations of the warnings that appear in this document, see the Regulatory Compliance and Safety Information document for
your router on Cisco.com:
http://www.cisco.com/en/US/docs/routers/connectedgrid/cgr1000/rcsi/cgr1000.rsci.html
When using the online publications, see the documents that match the Cisco system software version running on the WPAN module.
Hardware Overview
The CGM-WPAN-FSK-NA WPAN module provides IPv6-based, IEEE 802.15.4e/g-compliant, and highly secure wireless connectivity
for the CGR to enable Field Area Network (FAN) applications.
The module is ideal for standards-based IPv6 multihop mesh networks and long-reach solutions. It helps enable a high ratio of
endpoints to the CGR. The module provides the following functionality:
The CGM-WPAN-OFDM module is designed to operate within an RF900 wireless network to provide digital automation (DA)
control over Resilient Mesh Endpoints (RMEs) with serial (RS232/RS485), USB (LS/FS), or Fast Ethernet (10/100) ports for intelligent
control primarily in the electrical grid. CGR 1000s installed with a CGM-WPAN-OFDM module provide a low cost, low power,
small scale DA solution. Ruggedized IP41 enclosures are available for the CGR1000 to support installation within an outdoor cabinet.
• 902-to-928 MHz ISM band frequency hopping technology (configurable frequency range to match your country’s regulations).
See Technical Specifications, on page 10.
2
REVIEW DRAFT - CISCO CONFIDENTIAL