Technical Specs
Table Of Contents
- Cisco Connected Grid WPAN Module for CGR 1000 Series Installation and Cisco Resilient Mesh Configuration Guide (Cisco IOS)
- Cisco Connected Grid WPAN Module for CGR 1000 Series Installation and Cisco Resilient Mesh Configuration Guide (Cisco IOS)
- Hardware Overview
- WPAN Antennas, Connectors, and Cables
- Installing and Removing the Module
- Technical Specifications
- Information About Cisco Resilient Mesh and WPAN
- Configuring Cisco Resilient Mesh and the WPAN Module
- Configuring the WPAN Interface
- Configuring the CGM WPAN OFDM Module
- Configuring Adaptive Modulation
- Configuring Group Multicast
- Configuring RPL
- Configuring IPv6
- Configuring PON RPL
- Configuring the Power Outage Server
- Configuring QoS
- Configuring Cisco Resilient Mesh Security
- Configuring IPv6 Multicast Agent
- Configuring Dual-PHY WPAN
- Configuring DTLS Relay for EST
- Configuring Wi-SUN Mode
- Verifying Connectivity to the CGR
- show Command Examples
- Debugging the WPAN Module
- Sample Router Configuration
- Sample CGR and ASR Configuration
- Checking and Upgrading the WPAN Firmware Version
- Related Documentation
- Obtaining Documentation and Submitting a Service Request
DefinitionCommand
Enter a value between -65 and 35, where 25 is the default transmission power value.ieee154 txpower <-65 -
35 >
Enter a value between 15 and 255 seconds. Default is 120.[no] rpl dag-lifetime
<15 -255>
Enter command to enable RPL storing mode on the interface. Enter no rpl storing-mode to disable the
command.
CGR must be reloaded for the rpl storing-mode command to take effect.
Note
[no] rpl storing-mode
Sample Configuration
interface Wpan2/1
no ip address
ip broadcast-address 0.0.0.0
no ip route-cache
ieee154 beacon-async min-interval 10 max-interval 20 suppression-coefficient 1
ieee154 dwell window 12400 max-dwell 400
ieee154 panid 106
ieee154 phy-mode 149
ieee154 ssid edgecompute-secure
ieee154 txpower 25
rpl storing-mode
rpl dag-lifetime
rpl dio-dbl 5
rpl dio-min 16
rpl version-incr-time 120
authentication host-mode multi-auth
authentication port-control auto
ipv6 address 2046:FACE::/64
ipv6 dhcp relay destination 2001:FACE::200
no ipv6 pim
Configuring Adaptive Modulation
Adaptive modulation enhances the backward compatibility with the classic Cisco Resilient Mesh network and improves the transmitting
ability in the classic Cisco Resilient Mesh network. Adaptive modulation is supported on both Wi-SUN and Cisco mesh mode.
The following example shows the configuration of adaptive modulation in Wi-SUN mode:
(config)#interface wpan 4/1
(config-if)#ieee154 phy-mode
Supported Phy-Modes:
64:Rate=50 kb/s; Modulation=2FSK; Modulation Index=1.0; FEC=OFF; Channel Spacing=200 kHz
96:Rate=50 kb/s; Modulation=2FSK; Modulation Index=1.0; FEC=ON; Channel Spacing=200 kHz
66:Rate=150 kb/s; Modulation=2FSK; Modulation Index=0.5; FEC=OFF; Channel Spacing=400 kHz
98:Rate=150 kb/s; Modulation=2FSK; Modulation Index=0.5; FEC=ON; Channel Spacing=400 kHz
161:Rate=50 kb/s; Modulation=OFDM; Option=3; MCS=1; Channel Spacing=400 kHz
162:Rate=100 kb/s; Modulation=OFDM; Option=3; MCS=2; Channel Spacing=400 kHz
163:Rate=200 kb/s; Modulation=OFDM; Option=3; MCS=3; Channel Spacing=400 kHz
164:Rate=300 kb/s; Modulation=OFDM; Option=3; MCS=4; Channel Spacing=400 kHz
165:Rate=400 kb/s; Modulation=OFDM; Option=3; MCS=5; Channel Spacing=400 kHz
166:Rate=600 kb/s; Modulation=OFDM; Option=3; MCS=6; Channel Spacing=400 kHz
(config-if)#ieee154 phy-mode 166 165 164 163
31
REVIEW DRAFT - CISCO CONFIDENTIAL