Technical Specs
Table Of Contents
- Cisco Connected Grid WPAN Module for CGR 1000 Series Installation and Cisco Resilient Mesh Configuration Guide (Cisco IOS)
- Cisco Connected Grid WPAN Module for CGR 1000 Series Installation and Cisco Resilient Mesh Configuration Guide (Cisco IOS)
- Hardware Overview
- WPAN Antennas, Connectors, and Cables
- Installing and Removing the Module
- Technical Specifications
- Information About Cisco Resilient Mesh and WPAN
- Configuring Cisco Resilient Mesh and the WPAN Module
- Configuring the WPAN Interface
- Configuring the CGM WPAN OFDM Module
- Configuring Adaptive Modulation
- Configuring Group Multicast
- Configuring RPL
- Configuring IPv6
- Configuring PON RPL
- Configuring the Power Outage Server
- Configuring QoS
- Configuring Cisco Resilient Mesh Security
- Configuring IPv6 Multicast Agent
- Configuring Dual-PHY WPAN
- Configuring DTLS Relay for EST
- Configuring Wi-SUN Mode
- Verifying Connectivity to the CGR
- show Command Examples
- Debugging the WPAN Module
- Sample Router Configuration
- Sample CGR and ASR Configuration
- Checking and Upgrading the WPAN Firmware Version
- Related Documentation
- Obtaining Documentation and Submitting a Service Request
!
interface Wpan4/1
no ip address
ip broadcast-address 0.0.0.0
no ip route-cache
ieee154 beacon-async min-interval 120 max-interval 900 suppression-coefficient 1
ieee154 panid 7224
ieee154 ssid migration_far2
ieee154 txpower -30
authentication host-mode multi-auth
authentication port-control auto
ipv6 address 2092:1:1:1::/64
ipv6 enable
ipv6 dhcp relay destination 2010:A0B0:1001:22::2
dot1x pae authenticator
mesh-security mesh-key lifetime 259200
end
Router# show running-config interface wpan 5/1
Building configuration...
Current configuration : 481 bytes
!
interface Wpan5/1
no ip address
ip broadcast-address 0.0.0.0
no ip route-cache
ieee154 beacon-async min-interval 120 max-interval 900 suppression-coefficient 1
ieee154 panid 7215
ieee154 ssid plc123
slave-mode 4
rpl dag-lifetime 240
rpl dio-min 21
rpl version-incr-time 240
authentication host-mode multi-auth
authentication port-control auto
ipv6 address 2091:1:1:1::/64
ipv6 enable
ipv6 dhcp relay destination 2010:A0B0:1001:22::2
dot1x pae authenticator
end
Router#
show commands for Master-Slave WPANs
You can use the following show wpan commands to trace nodes in a Dual-PHY master-slave configuration:
• show wpan <master slot >/1 rpl itable—Shows information for the actual slot from which RPL DAOs originated.
• show wpan <master slot >/1 rpl stable—Shows slave slot information for the actual slot from which RPL DAOs originated.
• show wpan <master slot >/1 rpl stree—Shows the link type (or slave slot information) for each node in the RPL tree.
• show wpan <master slot >/1 eap-table—Shows slave slot information for the actual slot from which IEEE802.1x traffic
originated.
• All configurations and show commands related to the physical layer or the WPAN module hardware remain as is; show wpan
<slot >/1 hardware * remains the same, per the actual physical slot.
Router# show wpan 4/1 link-neighbors table
------------------------- WPAN LINK NEIGHBOR TABLE [4] -------------------------
EUI64 RSSIF RSSIR LQIF LQIR FIRST_HEARD LAST_HEARD
00078108003C2200 -70 -78 58 9 12:02:18 14:08:02
44
REVIEW DRAFT - CISCO CONFIDENTIAL










