Technical Specs
Table Of Contents
- Cisco Connected Grid WPAN Module for CGR 1000 Series Installation and Cisco Resilient Mesh Configuration Guide (Cisco IOS)
- Cisco Connected Grid WPAN Module for CGR 1000 Series Installation and Cisco Resilient Mesh Configuration Guide (Cisco IOS)
- Hardware Overview
- WPAN Antennas, Connectors, and Cables
- Installing and Removing the Module
- Technical Specifications
- Information About Cisco Resilient Mesh and WPAN
- Configuring Cisco Resilient Mesh and the WPAN Module
- Configuring the WPAN Interface
- Configuring the CGM WPAN OFDM Module
- Configuring Adaptive Modulation
- Configuring Group Multicast
- Configuring RPL
- Configuring IPv6
- Configuring PON RPL
- Configuring the Power Outage Server
- Configuring QoS
- Configuring Cisco Resilient Mesh Security
- Configuring IPv6 Multicast Agent
- Configuring Dual-PHY WPAN
- Configuring DTLS Relay for EST
- Configuring Wi-SUN Mode
- Verifying Connectivity to the CGR
- show Command Examples
- Debugging the WPAN Module
- Sample Router Configuration
- Sample CGR and ASR Configuration
- Checking and Upgrading the WPAN Firmware Version
- Related Documentation
- Obtaining Documentation and Submitting a Service Request
\--(RF )-- 2092:1:1:1:AAAA:8108:3C:2408
\--(RF )-- 2092:1:1:1:AAAA:8108:3C:2302
\--(RF )-- 2092:1:1:1:AAAA:8108:3C:2303
\--(RF )-- 2092:1:1:1:AAAA:8108:3C:2407
\--(RF )-- 2092:1:1:1:AAAA:8108:3C:240A
\--(RF )-- 2092:1:1:1:AAAA:8108:3C:2304
\--(RF )-- 2092:1:1:1:AAAA:8108:3C:2400
\--(RF )-- 2092:1:1:1:AAAA:8108:3C:2403
\--(RF )-- 2092:1:1:1:AAAA:8108:3C:2404
\--(RF )-- 2092:1:1:1:AAAA:8108:3C:2305
\--(RF )-- 2092:1:1:1:AAAA:8108:3C:2307
\--(RF )-- 2092:1:1:1:AAAA:8108:3C:2402
\--(RF )-- 2092:1:1:1:AAAA:8108:3C:2405
\--(RF )-- 2092:1:1:1:AAAA:8108:3C:2308
\--(RF )-- 2092:1:1:1:AAAA:8108:3C:2309
\--(RF )-- 2092:1:1:1:AAAA:8108:3C:240B
\--(RF )-- 2092:1:1:1:AAAA:8108:3C:230A
\--(RF )-- 2092:1:1:1:AAAA:8108:3C:230B
\--(RF )-- 2092:1:1:1:AAAA:8108:3C:2409
\--(RF )-- 2092:1:1:1:AAAA:8108:3C:2209
\--(RF )-- 2092:1:1:1:AAAA:8108:3C:220A
\--(PLC)-- 2092:1:1:1:AAAA:81FE:0:12C
\--(PLC)-- 2092:1:1:1:AAAA:81FE:0:12D
\--(PLC)-- 2092:1:1:1:AAAA:81FE:0:12E
\--(PLC)-- 2092:1:1:1:AAAA:81FE:0:12F
\--(PLC)-- 2092:1:1:1:AAAA:81FE:0:130
RPL SLOT TREE: Num.DataEntries 36, Num.GraphNodes 37 (external 0) (RF 31) (PLC 5)
Removing the Dual-PHY Master-Slave WPAN Configuration
This section describes how to remove the Dual-PHY master-slave relationship on a WPAN.
Before you begin
• Use show wpan 5/1 config to verify that the slave module is currently configured as slave.
• If the slave WPAN does not already have an IPv6 prefix assigned, assign a new IPv6 prefix while still in slave mode; for example,
ipv6 address 2091:1:1:1::/64.
• Use show mesh-security keys to verify that the slave module has no mesh-security keys configured. (See detailed CLI output
below.)
To remove an existing master-slave relationship between two WPANs, follow this procedure in exactly the sequence shown. The
example in this procedure uses WPAN 4/1 as master and WPAN 5/1 as slave.
Procedure
Step 1 From the interface config mode of the slave WPAN, enter no slave-mode <master-slot-number>:
Example:
Router# config t
Router(config)# interface wpan 5/1
Router(config-if)# no slave-mode 4
Router(config-if)# end
Step 2 Reload the slave module by powering off and then powering on:
47
REVIEW DRAFT - CISCO CONFIDENTIAL