Technical Specs
Table Of Contents
- Cisco Connected Grid WPAN Module for CGR 1000 Series Installation and Cisco Resilient Mesh Configuration Guide (Cisco IOS)
- Cisco Connected Grid WPAN Module for CGR 1000 Series Installation and Cisco Resilient Mesh Configuration Guide (Cisco IOS)
- Hardware Overview
- WPAN Antennas, Connectors, and Cables
- Installing and Removing the Module
- Technical Specifications
- Information About Cisco Resilient Mesh and WPAN
- Configuring Cisco Resilient Mesh and the WPAN Module
- Configuring the WPAN Interface
- Configuring the CGM WPAN OFDM Module
- Configuring Adaptive Modulation
- Configuring Group Multicast
- Configuring RPL
- Configuring IPv6
- Configuring PON RPL
- Configuring the Power Outage Server
- Configuring QoS
- Configuring Cisco Resilient Mesh Security
- Configuring IPv6 Multicast Agent
- Configuring Dual-PHY WPAN
- Configuring DTLS Relay for EST
- Configuring Wi-SUN Mode
- Verifying Connectivity to the CGR
- show Command Examples
- Debugging the WPAN Module
- Sample Router Configuration
- Sample CGR and ASR Configuration
- Checking and Upgrading the WPAN Firmware Version
- Related Documentation
- Obtaining Documentation and Submitting a Service Request
Time remaining : 29 Days 23 Hours 59 Minutes 47 Seconds
Key ID : 1
Key expiry : Mon Jul 21 12:55:43 2014
Time remaining : 59 Days 23 Hours 59 Minutes 47 Seconds
Router#
Verifying that WPAN 5/1 Forms Own RPL Table
Router# show wpan 5/1 rpl table
-------------------------------- WPAN RPL ROUTE TABLE [5] --------------------------------
NODE_IPADDR NEXTHOP_IP LAST_HEARD
2091:1:1:1:AAAA:81FE:0:12C 2091:1:1:1:: 13:42:17
2091:1:1:1:AAAA:81FE:0:12D 2091:1:1:1:: 13:40:47
2091:1:1:1:AAAA:81FE:0:12F 2091:1:1:1:: 13:41:59
Number of Entries in WPAN RPL ROUTE TABLE: 3
Notice above RMEs showing IPv6 address based on the WPAN 5/1 prefix.
Router# show wpan 5/1 rpl stable
------------------------------ WPAN RPL ROUTE SLOT TABLE [5] ------------------------------
NODE_IPADDR NEXTHOP_IP SSLOT LAST_HEARD
2091:1:1:1:AAAA:81FE:0:12C 2091:1:1:1:: 5 13:42:17
2091:1:1:1:AAAA:81FE:0:12D 2091:1:1:1:: 5 13:40:47
2091:1:1:1:AAAA:81FE:0:12F 2091:1:1:1:: 5 13:41:59
Number of Entries in WPAN RPL ROUTE SLOT TABLE: 3 (external 0) (RF 0) (PLC 3)
Notice above RMEs showing slot 5 for the WPAN 5/1.
Verifying the IPv6 Path to WPAN 5/1 Nodes
Router# ping 2091:1:1:1:AAAA:81FE:0:12C
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2091:1:1:1:AAAA:81FE:0:12C, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 256/268/276 ms
Router#
Configuring DTLS Relay for EST
The Cisco Resilient Mesh uses EST over CoAP/DTLS/UDP for certificate enrollment. During the initial bootstrapping process, nodes
that have already joined the network (enrolled and authenticated) act as DTLS relays for nodes being bootstrapped.
Use the following command to configure DTLS relay:
CGR#configure terminal
CGR(config)#interface wpan 4/1
CGR(config-if)#dtls-relay ?
X:X:X:X::X IPv6 address (aaaa:bbbb:cccc:dddd:eeee:ffff:gggg:hhhh, aaaa::bbb)
CGR(config-if)#dtls-relay 2060:FACD::6 ?
lifetime specify session lifetime
max-sessions specify maximum number of sessions
port destination port
52
REVIEW DRAFT - CISCO CONFIDENTIAL