Technical Specs
Table Of Contents
- Cisco Connected Grid WPAN Module for CGR 1000 Series Installation and Cisco Resilient Mesh Configuration Guide (Cisco IOS)
- Cisco Connected Grid WPAN Module for CGR 1000 Series Installation and Cisco Resilient Mesh Configuration Guide (Cisco IOS)
- Hardware Overview
- WPAN Antennas, Connectors, and Cables
- Installing and Removing the Module
- Technical Specifications
- Information About Cisco Resilient Mesh and WPAN
- Configuring Cisco Resilient Mesh and the WPAN Module
- Configuring the WPAN Interface
- Configuring the CGM WPAN OFDM Module
- Configuring Adaptive Modulation
- Configuring Group Multicast
- Configuring RPL
- Configuring IPv6
- Configuring PON RPL
- Configuring the Power Outage Server
- Configuring QoS
- Configuring Cisco Resilient Mesh Security
- Configuring IPv6 Multicast Agent
- Configuring Dual-PHY WPAN
- Configuring DTLS Relay for EST
- Configuring Wi-SUN Mode
- Verifying Connectivity to the CGR
- show Command Examples
- Debugging the WPAN Module
- Sample Router Configuration
- Sample CGR and ASR Configuration
- Checking and Upgrading the WPAN Firmware Version
- Related Documentation
- Obtaining Documentation and Submitting a Service Request
admin_status: up
Other show wpan hardware options are:
Router# show wpan 4/1 hardware ?
channel-list Channel list
config Configuration
debug Debug information
global-time Global time
hwversion Hardware version
key-info Mesh key information
leds LED status
link-neighbors Layer 2 link neighbor information
link-stats Link statistics
network-if-stats Network interface statistics
security-mode Security mode (enabled by dot1x)
test-mode Test mode (for test firmware only)
uptime Uptime
version Firmware version
The output of the command show wpan <slot >/1 hardware key shows mesh-security keys (GTKs) that reside on the WPAN
hardware. The show wpan <slot >/1 hardware key output should agree with the output of show mesh-security-keys . (See show
mesh-security keys, on page 39.)
Router# show wpan 4/1 hard key
keyinfo:
key 0: valid *
key 1: valid
key 2: empty
key 3: empty
key x: valid
The show wpan <slot >/1 hardware link-neighbor command shows the list of recently heard IEEE 802.15.4 link neighbors. These
link neighbors are RMEs within a 1-hop transmit range from the CGR and from which the CGR has recently heard IEEE 802.15.4
frames. The list shows only the most recently heard subset from all possible 1-hop neighbors.
Router# show wpan 4/1 hardware link-neighbors
eui64 heard etx sent / ack rssif / rssir lqif / lqir
0007810800A909A1 5 65535 0 / 0 n/a / -99 n/a / 41
0007810800CBF246 23 65535 0 / 0 n/a / -86 n/a / 76
0007810800000001 38 65535 0 / 0 n/a / -114 n/a / 127
00078108003C2206 59 263 3 / 3 - 71 / -74 36 / 14
00078108003C2202 65 278 0 / 0 - 71 / -77 72 / 36
00078108003C2207 113 258 1 / 1 - 71 / -76 14 / 18
Router# show wpan 4/1 hardware link-stats ?
bridge Link statistics bridge
brief Link statistics brief
ieee154-beacon Link statistics ieee154 beacon
ieee154-device Link statistics ieee154 device
ieee154-mac Link statistics ieee154 mac
lowpan Link statistics lowpan
radio Link statistics radio
Router# show wpan 4/1 hardware link-stats brief
linkstats info:
---------------
lowpan
tx frames: 5244 (1349356 bytes)
rx frames: 2483 (740228 bytes)
tx errors: 0
rx errors: 0
56
REVIEW DRAFT - CISCO CONFIDENTIAL