Cisco Prime Network Analysis Module Command Reference Guide Versions 5.1(2), 5.1(3), 6.0(1) and 6.0(2) December 2013 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
Contents About This Guide 9 1: Command Line Interface 12 2: NAM CLI Commands: application - device waas 16 application 18 application group 19 audit-trail enable 21 autocreate-data-source 22 cdp enable 23 cdp hold-time 24 cdp interval 25 classification-mode default 26 classification-mode deep-inspect 27 clear access log 28 clear captured-data-files 29 clear monitoring-data 30 clear system-alerts 31 clear system-passwords 32 clock set 33 config clear 34 config network
debug log reset 51 device erspan 52 device netflow 53 device waas 55 3: NAM CLI Commands: email – logout 56 email 57 entity alias 59 entity assetid 60 exit 61 exsession 62 ftp 63 help 65 ip address 66 ip broadcast 68 ip domain 69 ip gateway 70 ip host 71 ip hosts add 72 ip hosts delete 73 ip http port 74 ip http secure generate 76 ip http secure install certificate 77 ip http secure port 78 ip http secure server 79 ip http server 80 ip http tacacs+ 81 ip in
4: NAM CLI Commands: metric export host - show certificate request 89 metric export host 91 metric export non-waas traffic 92 monitor data-aggr-intv 93 monitor nbar 95 monitor protocol encapsulation 96 monitor rtp-stream enable 97 monitor rtp-stream filter 98 monitor rtp-stream threshold 99 monitor urlcollection 101 monitor urlfilter 103 mtrace-clear, mtrace-show, mtrace-start, mtrace-stop, mtrace-upload 105 netflow input port 106 nslookup 107 password 108 password strong-poli
show access-log 132 show application app-id 133 show application eng-id 134 show application group 135 show audit-trail 138 show autocreate-data-source 139 show cdb 140 show cdp settings 143 show certificate 144 show certificate-request 145 5: NAM CLI Commands: show clock details - show monitor urlfilter 146 show classification-settings 147 show clock details 148 show configuration 149 show corefiles 151 show counters 152 show cpu 153 show data-source 154 show date 155
show ip 172 show license 174 show local-storage all 175 show local-storage physical 180 show local-storage progress 184 show local-storage virtual 185 show log config 187 show log patch 188 show log report 189 show log upgrade 190 show memory 191 show metric export 192 show monitor protocol encapsulation 193 show monitor protocol all 194 show monitor rtp-stream 195 show monitor rtp-stream filter 196 show monitor urlcollection 197 show monitor urlfilter 198 6: NAM CLI Comm
show top-memory-users 215 show version 216 show waas data-source 217 show waas device 218 show waas server filter 219 show web-publication 220 show web-user 221 shutdown 222 snmp 223 syslog 224 syslog remote-server 225 terminal 227 time 228 traceroute 230 traceroute6 232 trap-dest 233 upgrade 235 waas export server-filter-list 236 waas import server-filter-list 237 waas server filter 238 web-publication 239 web-user 241 Appendix A NAM Maintenance Partition CLI 24
About This Guide ___________________________________________ This guide provides information for using the Cisco Prime Network Analysis Module (NAM) software command line interface (CLI). Audience This guide is designed for network administrators who are responsible for setting up and configuring Cisco Prime NAMs to monitor traffic and diagnose emerging problems on network segments. As a network administrator, you should be familiar with: Basic concepts and terminology used in internetworking.
___ Chapter 4 NAM CLI Commands: Lists CLI commands alphabetically and metric export host - show provides detailed information about the certificate request commands. Chapter 5 5: NAM CLI Commands: Lists CLI commands alphabetically and show provides detailed information about the classification-settings to commands. show monitor urlfilter Chapter 6 6: NAM CLI Commands: Lists CLI commands alphabetically and show password provides detailed information about the strong-policy - web user commands.
Information you enter boldface screen font Variables you enter italic screen Menu items and button names boldface font font Note Means reader take note. Notes contain helpful suggestions or references to material not covered in the publication. Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data. Caution Warning This symbol means danger. You are in a situation that could cause bodily injury.
1: Command Line Interface ___________________________________________ This chapter provides information for understanding and using the Cisco Prime Network Analysis Module Command Reference Guide software by using the command-line interface (CLI). This chapter includes the following sections: Logging into the NAM Getting Help Command Mode Subcommand Mode Creation and Edit Modes NAM Supported Platforms For an overview of your platform-specific configuration, see Cisco.com.
This example opens a session to log into the NAM-1, -2, or -3, and NAM-NX1 consoles: Step 1 Log into the console using the Telnet connection or the console port connection. Step 2 Establish a console session with the NAM at the CLI prompt, using the session/attach command. For example: Cisco IOS Software: switch> session slot 4 processor 1 The default escape character is Ctrl-^, then x. You can also type 'exit' at the remote prompt to end the session Trying 209.165.200.225 ...
Note After you log in for the first time, you will be asked to change the default password. Changing the Default Password To change the password, follow these steps while you are logged into the root account on the NAM: Step 1 Enter this command as follows: root@localhost# password username To change the root password, make a Telnet connection to the NAM and then use the password root command. To change the guest password, make a Telnet connection to the NAM and then use the password guest command.
Subcommand Mode Some commands enter into a subcommand mode, which provides additional configuration commands that you can use in that mode. For example: root@nam.domain.com# time Entering into subcommand mode for this command. Type 'exit' to apply changes and come out of this mode. Type 'cancel' to discard changes and come out of this mode. root@nam.domain.com(sub-time)# When you have entered the subcommand mode, type a ? or enter the help command for a list of commands available in that subcommand mode.
2: NAM CLI Commands: application - device waas ___________________________________________ This chapter contains an alphabetical listing of the commands unique to the Cisco platforms that support the 5.1(2), 5.1(3), 6.0(1) and 6.0(2) releases. For information on the supported platforms, see the Cisco Prime Network Analysis Module Release Notes. For information on Cisco IOS commands to configure your specific hardware platform, see Related Documentation.
Classification-mode default Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to use default NAM packet classification: root@nam.
classification-mode deep-inspect To use deep packet inspection (EFT feature), use the classification-mode deep-inspect command. This command is added in NAM 6.0(1). Classification-mode deep-inspect Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to use deep packet inspection: root@nam.
data-source waas debug log disable debug log enable debug log level debug log metric-engine debug log reset device erspan device netflow device waas Cisco Prime Network Analysis Module Command Reference Guide Page 19
application To create an application, use the application command. To remove an application match, use the no application command. application no application Defaults This command has no default settings. Command Modes Command mode Usage Guidelines When you enter the application submode, the following commands are available: cancel—Discards changes and exits from the subcommand mode. exit—Saves changes and exits from the subcommand mode; see the exit command section.
application group To enter the application group submode and define an application group, use the application group command. To remove an application group, use the no form of this command. application group no application group group-name Syntax Description group-name Application group name. Syntax Description Defaults This command has no default settings.
Examples This example shows how to create an application group named appGrpSample with two protocols in the group: root@NAM# application group Entering into subcommand mode for this command. Type 'exit' to come out of this mode. Type 'cancel' to discard changes and to come out of this mode.
audit-trail enable To enable and audit trail of GUI and CLI accesses, use the audit-trail enable command. To disable audit trail of GUI and CLI accesses, use the no form of this command. audit-trail enable no audit-trail enable Defaults Audit trail of the CLI and GUI accesses is enabled. Command Modes Command mode Examples This example shows how to enable an audit trail for GUI and CLI accesses: root@hostname.cisco.
autocreate-data-source To enable autocreation of the data-source, use the autocreate data-source command. To disable autocreation of data-sources on NAM, use the no form of this command. autocreate data-source no autocreate data-source Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to enable autocreation of data-sources: root@nam235Cat6k.cisco.
cdp enable To enable the Cisco Discovery Protocol (CDP) on the NME-NAM, use the cdp enable command. To disable CDP on the NME-NAM, use the no form of this command. cdp enable no cdp enable Note This command is not valid for NAM-1 or NAM-2 devices, the Cisco NAM 2200 Series appliances, or NAM Virtual Blades. Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to use default NAM packet classification: root@nam.
classification-mode deep-inspect To use deep packet inspection (EFT feature), use the classification-mode deep-inspect command. This command is added in NAM 6.0(1). Classification-mode deep-inspect Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to use deep packet inspection: root@nam.
cdp hold-time To set the Cisco Discovery Protocol (CDP) messages hold time, use the cdp hold-time command. To return the CDP messages hold time to the default value, use the no form of this command. cdp hold-time time no cdp hold-time Note This command is not valid for NAM-1 or NAM-2 devices or the Cisco NAM 2200 Series appliances. Syntax Description time Specifies the CDP hold time. Range is from 10 to 255 seconds. Syntax Description Defaults 180 seconds.
cdp interval To set the Cisco Discovery Protocol (CDP) messages interval on the NME-NAM, use the cdp interval command. To return the CDP messages interval on the NME-NAM to the default value, use the no form of this command. cdp interval time no cdp interval Note This command is not valid for NAM-1 or NAM-2 devices or the Cisco NAM 2200 Series appliances. Syntax Description time Specifies the CDP messages interval. Range is from 5 to 254 seconds.
classification-mode default To use default NAM packet classification, use the classification-mode default command. This command is added in NAM 6.0(1). Classification-mode default Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to use default NAM packet classification: root@nam.
classification-mode deep-inspect To use deep packet inspection (EFT feature), use the classification-mode deep-inspect command. This command is added in NAM 6.0(1). Classification-mode deep-inspect Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to use deep packet inspection: root@nam.
clear access log To clear the access log, use the clear access log command. clear access-log Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to clear the access log: root@localhost# clear access-log Related Commands secure-clear all To clean all users data before shipping, use the secure-clear all command. This is added in NAM 6.0(1).
Examples This example shows how to clean all users data before shipping: root@nam.localdomain# secure-clear all This operation will erase completely NAM user data. (including removing the NAM IP connectivity parameters such as IP address, To reconfigure the NAM network connectivity, you must use the switch/router session CLI command or UART port.
clear captured-data-files To delete all captured files from the NAM local hard drive, use the clear captured-data-files command. clear captured-data-files Defaults This command has no default settings.
clear monitoring-data To delete both short term and long term monitoring data, use the clear monitoring-data command. This command will also reset NAM to clean up cached data. clear monitoring-data Defaults This command has no default settings.
clear system-alerts To clear the system alerts, use the clear system-alerts command. clear system-alerts Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
clear system-passwords To reset or clear the CLI passwords, use the clear system-passwords command. clear system-passwords Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
clock set To set the date and time of a Cisco NAM 2000 series appliance, use the clock set command. clock set Note This command is only valid for Cisco NAM 2000 series appliances. Syntax Description hh:mm:ss: hh=hour, mm=minutes, ss=seconds mm/dd/yyyy mm = month, dd=day, yyyy=year Syntax Description Defaults This command has no default settings. Command Modes Command mode Usage Guidelines This command is supported only on the Cisco NAM 2200 Series appliances.
config clear To reset the NAM and return it to the factory-default state, use the config clear command. Please note the behavior of this command has been changed since 6.0(2) release. The network IP parameters will not be reset to factory-default starting from NAM 6.0(2) for config clear without option. config clear [all | ip] Syntax Description all (Optional) Resets all NAM configurations to factory default including the NAM IP parameters configuration.
NAM web interface preferences updated successfully. Successfully modified the configuration. NAM will be rebooted now, for the changes to take effect ...
config network To import a NAM configuration into the NAM from a specified location or to restore a NAM Virtual Blade license, use the config network command. config network url [config_filename] Syntax Description url Specifies the location of the configuration or license file to upload; ftp://@/ config_filename Specifies the filename for the configuration file. Syntax Description Defaults This command has no default settings.
Related Commands config upload Cisco Prime Network Analysis Module Command Reference Guide Page 42
config upload To upload the running NAM configuration to a specified location, use the config upload command. config upload url [config_filename] Syntax Description url Specifies the location of the configuration or license file to upload; ftp://@/ config_filename Specifies the filename for the configuration file. Syntax Description Defaults This command has no default settings.
Related Commands config network Cisco Prime Network Analysis Module Command Reference Guide Page 44
coredump To retrieve the core dump file, use the coredump command. coredump ftp://user:passwd@host/full-path/ Syntax Description ftp://user:passwd@host/full- Sets the path to the core dump file. path/ Syntax Description Defaults This command has no default settings.
data-source erspan To create ERSPAN (Encapsulated Remote SPAN) data-source, use the data-source erspan command. data-source erspan Defaults This command has no default settings. Command Modes Command mode Usage Guidelines When you enter the data-source erspan submode, the following commands are available: device-id—ERSPAN device ID. This is a mandatory value. cancel—Discards changes and exits from the subcommand mode.
data-source netflow To create NetFlow Data Export (NDE) data-source, use the data-source netflow command. data-source netflow Defaults This command has no default settings. Command Modes Command mode Usage Guidelines When you enter the data-source netFlow submode, the following commands are available: device-id—NetFlow device ID. This is a mandatory value. engine-id—NetFlow engine ID cancel—Discards changes and exits from the subcommand mode.
data-source pa To create performance agent (pa) data-source, use the data-source pa command. data-source pa Defaults This command has no default settings. Command Modes Command mode Usage Guidelines This command is supported on all NAM platforms. When you enter the data-source netFlow submode, the following commands are available: device-id—NetFlow device ID. This is a mandatory value. engine-id—NetFlow engine ID cancel—Discards changes and exits from the subcommand mode.
data-source waas To create Wide Area Application Services (WAAS) data-source, use the data-source waas command. data-source waas Defaults This command has no default settings. Command Modes Command mode Usage Guidelines When you enter the data-source waas submode, the following commands are available: device-id—WAAS device ID. This is a mandatory value. segment—This is the network segment that needs to be added to the data-source. This is a mandatory value.
(*) - denotes a mandatory field for this configuration.
debug log disable To disable debug logging, use the debug log disable command. debug log disable Syntax Description This command has no arguments or keywords. Defaults This command has no default behavior or settings. Command Modes Command mode Examples The following example disables all debug logging: root@nam.cisco.
debug log enable To enable debug logging, use the debug log enable command. debug log enable Syntax Description This command has no arguments or keywords. Defaults This command has no default behavior or settings. Command Modes Command mode Examples The following example enables all debug logging: root@nam.cisco.
debug log level To set the debug log level for each module running in NAM system, use the debug log-level command.
Examples The following example shows how to set the automated response time (ART) feature to display all log messages up to log level 2. This command will log all messages generated by the ART module that have log levels set to critical, error, and warning. root@nam.cisco.
debug log metric-engine To set debug log metric-engine, use the debug log metric-engine command. debug log metric-engine Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes Command mode Examples The following example sets the debug log level metric-engine: root@nam.cisco.
debug log reset To reset debug logging level back to default settings, use the debug log reset command. debug log reset Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes Command mode Examples The following example resets all debug log levels back to default values: root@nam.cisco.
device erspan To create an ERSPAN (Encapsulated Remote SPAN) device, use the device erspan command. device erspan Defaults This command has no default settings. Command Modes Command mode Usage Guidelines When you enter the device erspan submode, the following commands are available: address—IP address of the device. This is a mandatory value. cancel—Discards changes and exits from the subcommand mode. exit—Saves changes and exits from the subcommand mode; see the exit command section.
device netflow To create a NetFlow Data Export (NDE) device, use the device netflow command. device netflow Defaults This command has no default settings. Command Modes Command mode Usage Guidelines When you enter the device netFlow submode, the following commands are available: address—IP address of the device. This is a mandatory value. community—SNMPv2c community string cancel—Discards changes and exits from the subcommand mode.
root@nam235Cat6k.cisco.
device waas To create Wide Area Application Services (WAAS) device, use the device waas command. device waas Defaults This command has no default settings. Command Modes Command mode Usage Guidelines When you enter the device WAAS submode, the following commands are available: address—IP address of the device. This is a mandatory value. passthru—This is the passthru enable or disable traffic from the WAAS device. cancel—Discards changes and exits from the subcommand mode.
3: NAM CLI Commands: email logout ___________________________________________ This chapter provides information about the following commands: email entity alias entity assetid entity assetidexsession exit help ip address ip broadcast ip domain ip gateway ip host ip hosts add ip hosts delete ip http port ip http secure generate ip http secure install certificate ip http secure port ip http secure server ip http server ip http taca
email To set up an e-mail server that sends both alarm and report data through e-mail, enable or disable alarm messages sent through e-mail, and to enter the subcommand mode, use the email command. To remove the e-mail server, use the no email server command. To stop sending out both scheduled report data and alarm messages through e-mail, use the no email alarm command. email no email server no email alarm Syntax Description This command has no arguments or keywords.
root@localhost# email proot@localhost(sub-email)# server example-email.domain.com root@localhost(sub-email)# alarm enable root@localhost(sub-email)# alarm recipients admin@domain.com another_admin@domain.com root@localhost(sub-email)# exit Successfully set email configuration settings.
entity alias To configure an entity alias for the entity MIB, use the entity alias command. entity alias string Syntax Description String Specifies the entity string used to configure the entPHysicalAlias. Syntax Description Defaults This command has no default settings. Command Modes Command mode Usage Guidelines The entity MIB makes the entPhysicalTable and entLastChangeTime available through SNMP.
entity assetid To configure an entity MIB asset ID, use the entity assetid command. entity assetid string Syntax Description String Specifies the entity string used to configure the entPHysicalAssetID. Syntax Description Defaults This command has no default settings. Command Modes Command mode Usage Guidelines The entity MIB makes the entPhysicalTable and entLastChangeTime available through SNMP.
exit To log out of the system or to leave a subcommand mode, use the exit command. exit Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Usage Guidelines To leave a subcommand mode, use the exit command. The exit command saves any changes before leaving the submode.
exsession To enable or disable outside logins, use the exsession command. exsession on [ssh] exsession off Syntax Description on Enables outside logins. off Disables outside logins. ssh (Optional) Sets the outside logins to SSH. Syntax Description Defaults This command has no default settings. Command Modes Command mode Usage Guidelines A strong crypto patch is required if you use the ssh option.
ftp To set the FTP server and directory for storing scheduled reports, use the ftp command. To disable FTP scheduled reports, use the no form of this command. ftp no ftp Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Usage Guidelines When you enter the FTP subcommand mode, the following commands are available: ? or help—Displays help; see the help command section.
directory exit help index password server user - FTP location at the FTP server - exit from subcommand mode - display help - a unique integer identifying the ftp entry - password of the user at the FTP server - set FTP server - user name at the FTP server Cisco Prime Network Analysis Module Command Reference Guide Page 69
help To display help, use the help command or ?. You must press the Enter key after entering the ?. help | ? Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode or subcommand mode. Examples This example shows how to display help: nam.domain.
ip address To set the system IP address, use the ip address command. IPv6 support has been added in NAM 6.0(1). ip address ip-address subnet-mask Syntax Description ip-address Sets the system IP address. subnet-mask Sets the subnet mask. Syntax Description Defaults This command has no default settings. Command Modes Command mode Usage Guidelines After setting the IP address, the gateway address may be set to 0.0.0.0.
HTTP port: HTTP secure port: TACACS+ configured: Telnet: SSH: root@localhost# 80 443 No Enabled Disabled Related Commands ip broadcast ip domain ip host Cisco Prime Network Analysis Module Command Reference Guide Page 72
ip broadcast To set the system broadcast address, use the ip broadcast command. ip broadcast broadcast-address Syntax Description broadcast-address Sets the system broadcast address. Syntax Description Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to set the system broadcast address: root@localhost# ip broadcast 172.20.104.
ip domain To set the system domain name, use the ip domain command. ip domain name Syntax Description Name Sets the system domain name. Syntax Description Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to set the IP domain name: root@nam# ip domain cisco.com root@nam.cisco.
ip gateway To set the system default gateway address, use the ip gateway command. ip gateway default-gateway Syntax Description default-gateway Sets the default gateway address. Syntax Description Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to set the IP gateway address: root@localhost# ip gateway 123.34.56.
ip host To set the system hostname, use the ip host command. ip host name Syntax Description Name Sets the IP hostname. Syntax Description Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to set the IP hostname: root@NAM.cisco.com# ip host orion root@orion.cisco.
ip hosts add To add or replace host entries, use the ip hosts add command. ip hosts add ip-address host-name [alias1] [alias2] ip hosts add ftp://user:passwd@host/full-path/filename Syntax Description ip-address Sets the host IP address. host-name Sets the hostname which can be a FTP URL with a filename. alias1 alias2 (Optional) Sets the host alias. ftp://user:passwd@host/full-path/fi Sets the path to the host parameters file lename location.
ip hosts delete To delete host entries, use the ip hosts delete command. ip hosts delete ip-address ip hosts delete ftp://user:passwd@host/full-path/filename Syntax Description ip-address Sets the host IP address. ftp://user:passwd@host/full-path/fi Sets the path to the host parameters file lename location. Syntax Description Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to delete a specific IP host: root@localhost# ip hosts delete 30.50.
ip http port To set the HTTP port, use the ip http port command. ip http port 1-65535 Syntax Description 1-65535 Specifies a port number in the range of 1 through 65535. Syntax Description Not all ports are available to be assigned. Most browsers block ports that are used for other applications. Commonly-Blocked Ports lists the commonly blocked ports.
25 smtp 111 sunrpc 515 printer 37 time 113 auth 526 tempo 42 name 115 sftp 530 courier Defaults This command has no default settings.
ip http secure generate To generate a certificate request, use the ip http secure generate command. ip http secure generate {certificate-request | self-signed-certificate} Syntax Description certificate-request Generates a certificate request. self-signed-certificate Generates a self-signed certificate. Syntax Description Defaults This command has no default settings.
ip http secure install certificate To install a certificate, use the ip http secure install certificate command. ip http secure install certificate Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
ip http secure port To set up a secure server port, use the ip http secure port command. ip http secure port port Syntax Description Port Sets the HTTP secure port. Syntax Description Not all ports are available to be assigned. Most browsers block ports that are used for other applications. Commonly-Blocked Ports on page 78 lists the commonly blocked ports. Defaults This command has no default settings.
ip http secure server To set up a secure server, use the ip http secure server command. ip http secure server {enable | disable} Syntax Description server enable | disable Enables or disables the HTTP server. Syntax Description Defaults This command has no default settings. Command Modes Command mode Usage Guidelines A strong crypto patch is required before applying this command.
ip http server To enable a HTTP server, use the ip http server command. ip http server {enable | disable} Syntax Description enable Enables the HTTP server. disable Disables the HTTP server. Syntax Description Defaults This command has no default settings.
ip http tacacs+ To enable a TACACS+ server, use the ip http tacacs+ command. ip http tacacs+ enable primary-srv [backup-srv] [en-secret-key encrypted-secret-key] ip http tacacs+ disable Syntax Description disable Disables the TACACS+ server. enable Enables the TACACS+ server. primary-srv Specifies the primary TACAC+ server. backup-srv (Optional) Specifies the backup TACACS+ server. en-secret-key (Optional) Argument name to enable the secret key. encrypted-secret-key (Optional) Argument value.
Secret key: Repeat secret key: Successfully enabled Tacacs+ root@hostname.cisco.com# show ip IP address: 172.20.98.177 Subnet mask: 255.255.255.192 IP Broadcast: 172.20.255.255 DNS Name: hostname.cisco.com Default Gateway: 172.20.98.129 Nameserver(s): 171.69.2.133 HTTP server: Enabled HTTP secure server: Disabled HTTP port: 80 HTTP secure port: 443 TACACS+ configured: Yes TACACS+ primary server: 10.0.0.1 TACACS+ backup server : 10.0.0.2 Telnet: Enabled SSH: Disabled root@hostname.cisco.
ip interface To select the external port or the internal ports for the NME-NAM, use the ip interface command. ip interface external | internal Note This command is not valid for NAM-1 or NAM-2 devices, the Cisco NAM 2200 Series appliances, or the Cisco NAM Virtual Blades. Syntax Description external Selects the RJ-45 Fast Ethernet connector on the NME-NAM.
ip nameserver To set or disable system name server entries, use the ip nameserver command. ip nameserver ip-addr ip-addr ip-addr or ip nameserver disable Syntax Description ip-addr Sets the name server address. disable Disables the name server entries. Syntax Description Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to set a system name server: root@localhost# ip nameserver 171.69.2.
license install To install a license file on a WAE device that has installed NAM Virtual Blade software, use the license install command. license install url Syntax Description url Specifies the location of the license file to install; ftp://@// Syntax Description Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
logout To log out of the system, use the logout command. logout Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
managed-device address To configure the managed device address, use the managed-device address command. To remove the managed device ip address, use the no managed-device address. This no manage-device command is added in NAM 6.0(1). no managed-device address managed-device address Note This command is not supported on NAM-1, NAM-2, NME-NAM-80S, NME-NAM-120S and the NAM Virtual Blade devices. Syntax Description ip-address Specifies the IP address of the managed device.
managed-device community To configure the managed device SNMP community, use the managed-device community command. To remove the managed device community string, use the no managed-device community command. This remove command is added in NAM 6.0(1). No managed-device community managed-device community Note This command is not supported on NAM-1, NAM-2, NME-NAM-80S, NME-NAM-120S and the NAM Virtual Blade devices.
4: NAM CLI Commands: metric export host - show certificate request ___________________________________________ This chapter describes the following NAM CLI commands: metric export host metric export non-waas traffic monitor data-aggr-intv To set data aggregation intervals, use the monitor data-aggr-intv command. This command is added in NAM 6.0(1). Monitor data-aggr-intv Defaults This command has no default settings.
short-term-rsp-time [min]—Specify short term interval for application response time (min). short-term-traffic [min]—Specify short term interval for traffic/media (min). Examples This example shows how to set data aggregation intervals: root@nam.localdomain# monitor data-aggr-intv Entering into subcommand mode for this command. Type 'exit' to apply changes and come out of this mode. Type 'cancel' to discard changes and come out of this mode. root@nam.localdomain(sub-data-aggr-intv) # root@nam.
reboot reboot -helper reboot -golden remote-storage remote-storage fcoe remote-storage iscsi remote-storage sas rmwebusers show access-log show application app-id show application eng-id show application group show audit-trail show autocreate-data-source show cdb show cdp settings show certificate Cisco Prime Network Analysis Module Command Reference Guide Page 96
metric export host To configure the metric export host, use the metric export host command. To disable metric export, use the no form of this command. metric export host ip-address [port] no metric export Syntax Description ip-address Specifies the IPv4 address of the external reporting console. port Port the external reporting console is listening on for incoming packets (optional). Syntax Description Defaults The default port is 9995.
metric export non-waas traffic To send SPAN traffic (non-WAAS traffic) to an external reporting console, use the metric export non-waas traffic command. To disable metric export, use the no form of this command. metric export non-waas traffic no metric export non-waas traffic Syntax Description This command has no arguments or keywords. Defaults Export is disabled. Command Modes Command mode Usage Guidelines Use this command to export non-waas (SPAN traffic) metrics to an external reporting console.
monitor data-aggr-intv To set data aggregation intervals, use the monitor data-aggr-intv command. This command is added in NAM 6.0(1). Monitor data-aggr-intv Defaults This command has no default settings. Command Modes Command mode Usage Guidelines When you enter the monitor data-aggr-intv submode, the following commands are available: ?—Displays help. (Added in 6.0(2) cancel—Discards changes and exits from the subcommand mode. exit—exits from the subcommand mode. help—Displays help.
root@nam.localdomain(sub-data-aggr-intv) # root@nam.
monitor nbar To enable supervisor NBAR statistics polling, use the monitor nbar command. To disable polling, use the no form of this command. monitor nbar no monitor nbar Syntax Description This command has no arguments or keywords. Defaults This command has no defaults. Command Modes Command mode Usage Guidelines The NBAR-PD-MIB must be present to enable the collection of statistical information. The NAM-3 statistics are polled from the supervisor engine.
monitor protocol encapsulation To set the protocol encapsulation, use the monitor protocol encapsulation command. To disable the protocol encapsulation, use the no form of this command. This command is removed in NAM 6.0(1). monitor protocol encapsulation no monitor protocol encapsulation Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to set the monitor protocol encapsulation.
monitor rtp-stream enable To enable RTP stream monitoring, use the monitor rtp-stream enable command. To disable RTP stream monitoring, use the no form of this command. monitor rtp-stream enable no monitor rtp-stream enable Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to enable RTP stream monitoring. root@localhost# monitor rtp-stream enable This example shows how to disable RTP stream monitoring.
monitor rtp-stream filter To set a RTP stream filtering entry, use the monitor rtp-stream filter command. To remove a RTP stream filtering entry, use the no form of this command. monitor rtp-stream filter source-address source-mask dest-address dest-mask Syntax Description source-address Specifies the source address of the RTP stream being filtered. source-mask Specifies the subnet mask of the source address of the RTP stream being filtered.
monitor rtp-stream threshold To set the alarm threshold for the different RTP stream monitoring types, use the monitor rtp-stream threshold command. To disable the alarm threshold RTP stream monitoring, use the no form of this command. monitor rtp-stream threshold no monitor rtp-stream threshold Syntax Description Key Word Action actual-pkt-loss Specifies the actual packet loss percentile threshold and enables the actual packet loss threshold alarm.
Examples This example shows how to set an alarm threshold of 6% for RTP stream monitoring of lost packets. root@NAM.cisco.com# monitor rtp-stream threshold adjusted-pkt-loss 6 Successfully set adjusted-pkt-loss alarm. root@NAM.cisco.
monitor urlcollection To enter the URL collection submode and configure URL collection, use the monitor urlcollection command. To disable the URL collection, use the no form of this command. monitor urlcollection no monitor urlcollection Syntax Description This command has no keywords or arguments. Defaults This command has no default settings.
There is only one URL collection in NAM. The collection owner is always LocalMgr. The index is always one. Examples This example shows how to configure URL collection: root@localhost# monitor urlcollection Entering into subcommand mode for this command. Type 'exit' to apply changes and come out of this mode. Type 'cancel' to discard changes and come out of this mode.
monitor urlfilter To enter the URL filter collection configuration subcommand mode, and then configure URL filters, use the monitor urlfilter command. To remove the URL filters from the configuration, use the no form of this command. This command is removed in NAM 6.0(1). monitor urlfilter no monitor urlfilter control-index Syntax Description control-index Specifies the collection control index. Range is from 1 to 65535. Syntax Description Defaults The control index is random.
The clear configuration command removes the URL filters from the configuration. There is no SNMP support for configuring the URL filters. Examples This example shows how to configure URL filters: root@nam# monitor urlfilter Entering into subcommand mode for this command. Type 'exit' to come out of this mode. Type 'cancel' to discard changes and to come out of this mode.
mtrace-clear, mtrace-show, mtrace-start, mtrace-stop, mtrace-upload These are memory debug commands. They are not for NAM feature use. Please do not use without request from NAM support engineers. mtrace-clear mtrace-show mtrace-start mtrace-stop mtrace-upload url-path Syntax Description The first four commands have no arguments or keywords. mtrace-upload needs FTP pathname for mtrace upload Defaults These commands have no default settings.
netflow input port To set a specified value of the input NetFlow UDP port on NAM, use the netflow input port [port] command. netflow input port [port] Note In case this CLI is not used, NAM retains the default port 3000 to listen to incoming NDEs. When invoked, the CLI prints both old and new UDP port numbers, if successfully completed. Syntax Description port Specifies the input UDP port number, valid values 1 65535. Syntax Description Defaults The default port is 3000.
nslookup To configure name server queries, use the nslookup command. nslookup hostname [server] Syntax Description hostname Specifies the name server query host. server (Optional) Specifies the name server to query. Syntax Description Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to configure name server queries: root@localhost.cisco.com# nslookup www.yahoo.com Server: 127.0.0.1 Address: 127.0.0.1#53 Non-authoritative answer: www.yahoo.
password To set a new password, use the password command. password username Syntax Description username Sets the user login name whose password will be changed. Syntax Description Defaults This command has no default settings. Command Modes Command mode Usage Guidelines There are only two valid users, root and guest. Examples This example shows how to set a password: root@localhost.cisco.
password strong-policy To enable strong password policy for user names, use the password strong-policy command. To disable this option, use the no form of this command. password strong-policy no password strong-policy Defaults This command has no default settings. Command Modes Command mode Usage Guidelines There are only two valid users, root and guest. Examples This example shows how to set a password: root@localhost.cisco.com# password strong-policy Strong password policy is enabled.
patch To download and install a software patch, use the patch command. patch ftp://user:passwd@host/full-path/filename Syntax Description ftp://user:passwd@host/full-path/file Sets the path to download the patch. name Syntax Description Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to download and install a patch: root@localhost.cisco.com# patch ftp://hostname/fullpath/c6nam-3.6-strong-cryptoK9-patch-1-0.bin Proceeding with installation.
pid-sn To enter the Product ID and Serial number of a WAE device for node locking with a NAM Virtual Blade product license, use the pid-sn command. This command is removed in NAM 6.0(1). pid-sn PIDnnnn SNnnnn Syntax Description PIDnnnn Specifies the Product ID of the WAE device. SNnnnn Specifies the serial number of the WAE device. Syntax Description Defaults This command has no default settings. Command Modes Command mode Usage Guidelines This command is valid only on NAM Virtual Blade platforms.
ping To check connectivity to a IPv4 network device, use the ping command. ping [-n | -v] [-c count] [-i wait] [-p pattern] [-s packetsize] hostname | IP address Syntax Description -n (Optional) Displays the network addresses as numbers. -v (Optional) Specifies verbose output. -c count (Optional) Stops the ping after sending the count of ECHO_REQUEST packets. -i wait (Optional) Specifies the time interval in seconds between sending each packet.
ping6 To check connectivity to a IPv6 network device, use the ping6 command. This command is added in NAM 6.0(1). Ping6 [-n | -v] [-c count] [-i wait] [-p pattern] [-s packetsize] [-I interface] [-M hint] hostname | IP address Syntax Description -n (Optional) Displays the network addresses as numbers. -v (Optional) Specifies verbose output. -c count (Optional) Stops the ping6 after sending the count of ECHO_REQUEST packets.
Examples This example shows how to check the connectivity of a network device with ping6: Cisco Prime Network Analysis Module Command Reference Guide Page 120
preferences To enter the preferences subcommand mode, and then configure how your screen displays information, use the preferences command. preferences Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Usage Guidelines When you enter the preferences subcommand mode, the following commands are available: cancel—Discards changes and exits from the subcommand mode.
Capture-format pcap—set pcap as capture format. This is added in NAM 6.0(1). Examples This example shows how to configure preferences for your screen display: root@nam.localdomain# preferences Entering into subcommand mode for this command. Type 'exit' to apply changes and come out of this mode. Type 'cancel' to discard changes and come out of this mode. root@nam.localdomain(sub-preferences)# audit-trail enable root@nam.localdomain(sub-preferences)# capture-format enc root@nam.
protocol esp-null-heuristic Use the protocol esp-null-heuristic command to enable and disable the NAM to parse ESP-NULL protocol heuristically. To enable the NAM to parse ESP-NULL protocol heuristically, use the following command: protocol esp-null-heuristic enable To disable the NAM to parse ESP-NULL protocol heuristically, use the following command: no protocol esp-null-heuristic enable Syntax Description This command enables and disables heuristic parsing of ESP-NULL packets.
reboot To shut down and then restart NAM, use the reboot command. reboot Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
reboot -helper To reboot to helper image, use the reboot -helper command. reboot -helper Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
reboot -golden To reboot to the golden helper image (NAM-3), use the reboot -golden command. reboot -golden Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
remote-storage Related Commands remote-storage fcoe remote-storage iscsi remote-storage sas Cisco Prime Network Analysis Module Command Reference Guide Page 127
remote-storage fcoe To list or format the FCoE remote storage targets for capture data, use the remote-storage fcoe command. remote-storage fcoe Syntax Description name Specifies the name for the FCoE remote storage being removed. Syntax Description Defaults This command has no default settings. Command Modes Command mode Usage Guidelines These commands are supported only on NAM-3. When you enter the command, the following are available: format—Formats one or more FCoE storage targets.
Examples This example shows how to configure a remote storage for capturing FCoE data: root@hostname.cisco.
remote-storage iscsi To list or format the iSCSI remote storage targets for capture data, use the remote-storage iscsi command. remote-storage iscsi Syntax Description name Specifies the name for the iSCSI remote storage being removed. Syntax Description Note This command is not supported on the NAM WAAS Virtual Blade. Defaults This command has no default settings.
Examples This example shows how to configure a remote storage for capturing iSCSI data: root@hostname.cisco.
remote-storage sas To list or format the SAS remote storage targets for capture data, use the remote-storage sas command. remote-storage sas Syntax Description name Specifies the name of the SAS remote storage being removed. Syntax Description Defaults This command has no default settings. Command Modes Command mode Usage Guidelines These commands are supported only on NAM-3. When you enter the command, the following are available: format—Format one or more SAS storage targets.
format label list local-address mount unmount - format one or more SAS storage targets - label a SAS storage target - list all SAS storage targets - show local SAS Address - re-mount a SAS storage target - unmount a SAS storage target (safely remove) Cisco Prime Network Analysis Module Command Reference Guide Page 133
remove corefiles To remove all existing core files, use the remove corefiles command. This is added in NAM 6.0(1). Remove corefiles Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to remove all existing core files: root@nam.localdomain# remove corefiles root@nam.
rise-nam enable / disable To enable or disable nam rise interface, use the rise-nam enable / disable command. This is added in NAM 6.0(2) and currently only works on NAM 2300 appliances. rise-nam enable | disable Syntax Description disable disable RISE for NAM appliance. enable enable RISE for NAM appliance. Defaults default is disable for 6.0(2). Command Modes Command mode Examples These examples show how to enable and disable rise interface on NAM appliances: root@nam.
rmwebusers To remove all web users from the local web user database, use the rmwebusers command. rmwebusers Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to remove web users from the local web user database: root@localhost.cisco.com# rmwebusers WARNING:Doing this will stop the web server and remove all locally defined web users from web user database.
secure-clear all To clean all users data before shipping, use the secure-clear all command. This is added in NAM 6.0(1). Secure-clear all Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to clean all users data before shipping: root@nam.localdomain# secure-clear all This operation will erase completely NAM user data.
show access-log To display the web access log, use the show access-log command. show access-log Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display the web access log: Root@localhost# show access-log 11 Mar 2003, 12:23:38 152.20.27.182 /error.php 11 Mar 2003, 12:23:39 152.20.27.182 /error.php 11 Mar 2003, 12:23:39 152.20.27.182 /error.php 11 Mar 2003, 12:23:39 152.20.27.
show application app-id To display all applications, use the show application app-id command. show application app-id Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display all applications: root@NAM.cisco.
show application eng-id To display application information per engine ID, use the show application eng-id command. show application eng-id Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display application information per engine ID: root@NAM.cisco.
show application group To display application groups, use the show application group command. show application group [group-name] Syntax Description group-name (Optional) Specifies the application group name. Syntax Description Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display application groups: root@namlab-kom10.cisco.com# show application group Application Group: File-Transfer Number of Protocols: 5 - ftp 16.1.0.0.1.0.0.8.0.0.0.0.
16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.26.43.4.0.1.0.0 - edonkey(udp) 16.1.0.0.1.0.0.8.0.0.0.0.17.0.0.18.57.4.0.1.0.0 - edonkey(tcp) 16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.18.53.4.0.1.0.0 - hotline 16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.21.124.4.0.1.0.0 - soulseek 16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.8.186.4.0.1.0.0 - directconnect 16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.1.155.4.0.1.0.0 - bittorrent 16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.26.225.4.0.1.0.0 Application Group: Web Number of Protocols: 2 - http 16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.0.80.4.0.1.0.
- h225 16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.6.184.4.0.1.0.0 - h245 16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.6.182.4.0.1.0.0 - h323-gatekeeper 16.1.0.0.1.0.0.8.0.0.0.0.17.0.0.6.183.4.0.1.0.0 - rtp 16.1.0.0.1.0.0.8.0.0.0.0.17.0.0.125.0.4.0.1.0.0 - rtcp 16.1.0.0.1.0.0.8.0.0.0.0.17.0.0.125.1.4.0.1.0.0 - sip(udp) 16.1.0.0.1.0.0.8.0.0.0.0.17.0.0.19.196.4.0.1.0. - sip(tcp) 16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.19.196.4.0.1.0.0 - mgcp 16.1.0.0.1.0.0.8.0.0.0.0.17.0.0.9.123.4.0.1.0.0 - sccp 16.1.0.0.1.0.0.8.0.0.0.0.6.0.0.7.208.4.0.1.0.
show audit-trail To display the audit trail configuration, use the show audit-trail command. show audit-trail Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display the audit trail configuration: root@hostname.cisco.com# show audit-trail Audit trail is enabled. root@hostname.cisco.
show autocreate-data-source To display the autocreated data-sources, use the show autocreate-data-source command. show autocreate-data-source Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows if the autocreation of data-sources feature is enabled: root@NAM.cisco.
show cdb To display information about a CDB file, use the show cdb command. Since NAM 6.0(1), this command has been changed from show cdb [filename] to the specific cdb names.
Syntax Description Filename ARTCltSvr Specifies the CDB filename.
Examples This example shows how to display information about a CDB file: root@nam.localdomain# show cdb - File to examine (e.g.
show cdp settings To display the current Cisco Discovery Protocol (CDP) settings, use the show cdp settings command. show cdp settings Note This command is not supported on NAM-1 or NAM-2 devices or the NAM Virtual Blade. Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Usage Guidelines This command is supported only on NME-NAM-80S and NME-NAM-120S devices and Cisco NAM 2200 Series appliances.
show certificate To display the installed certificate, use the show certificate command. show certificate Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
show certificate-request To display the certificate-signing requests, use the show certificate-request command. show certificate-request Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
5: NAM CLI Commands: show classification-settings to show monitor urlfilter ___________________________________________________________________________________________ This chapter describes the following NAM CLI commands: ―show classification-settings‖ to ―show monitor urlfilter‖.
show classification-settings To show current packet classification setting on the NAM, use the show classification-settings command. This command is added in NAM 6.0(1). show classification-settings Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples The following example shows how to display current packet classification settings. root@nam.
show clock details To show clock details on the NAM, use the show clock details command. show clock details Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples The following example shows how to display clock settings. root@nam.cisco.
show configuration To display the NAM running configuration, use the show configuration command. show configuration Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
rsp-time4 50 rsp-time5 100 rsp-time6 500 rsp-timeout 1000 exit ! Related Commands config clear Cisco Prime Network Analysis Module Command Reference Guide Page 156
show corefiles To display the corefiles, use the show corefiles command. This command is added in NAM 6.0(1). show corefiles Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display corefiles: root@nam.localdomain# show corefiles root@nam.
show counters To display the counters for data aggregation table, use the show counters command. show counters Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display the counters for data aggregation table: root@nam235Cat6k.cisco.
show cpu To display the Central Processing Unit (CPU) utilization, use the show cpu command. show cpu Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display the CPU utilization: root@nam235Cat6k.cisco.com# show cpu NOTE: For more details on system resources including CPU utilization, visit the Administration -> System -> Resources page in the NAM Traffic Analyzer web application.
show data-source To display the data-sources, use the show data-source command. show data-source Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display the data-sources: root@nam235Cat6k.cisco.
show date To display the current date and time, use the show date command. show date Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
show debug log-levels To display log level settings, use the show debug log-levels command. show debug log-levels Syntax Description This command has no arguments or keywords. Defaults This command has no default behavior or settings. Command Modes Command mode Examples The following example shows log level settings: root@nam.cisco.
Feature Feature Feature Feature Feature Feature Feature Feature Feature RMON2_PDIST (33): error (1) RMON2_HOST (34): error (1) RMON2_MATRIX (35): error (1) DSMON_STATS (36): error (1) DSMON_PDIST (37): error (1) DSMON_HOST (38): error (1) DSMON_MATRIX (39): error (1) SMON_PRIO (40): error (1) SMON_VLAN (41): error (1) Cisco Prime Network Analysis Module Command Reference Guide Page 163
show debug messages To display NAM log file contents, use the show debug messages command. show debug messages Syntax Description This command has no arguments or keywords. Defaults This command has no default behavior or settings. Command Modes Command mode Examples The following example shows the log file contents: root@nam.cisco.
show debug metric-engine To display metric-engine log file, use the show debug metric-engine command. show debug metric-engine Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display metric-engine log file: root@nam235Cat6k.cisco.
show debug online-diag-stats To display the online diagnostic status log file, use the show debug online-diag-stats command. show debug online-diag-stats Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display the online diagnostic status log file: root@nam235Cat6k.cisco.
show debug rise-messages To display the debug RISE log messages, use the show debug rise-messages command. This command is added in NAM 6.0(1). show debug rise-messages Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display the debug RISE log messages: root@nam.localdomain# show debug rise-messages root@nam.
show decode-log To display the packet decode log, use the show decode-log command. This command is added in 6.0(2). show decode-log Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
show device To display the remote devices like ERSPAN, NetFlow, and WAAS, use the show device command. show device Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
show email To display email settings that are used for e-mailing alarm messages or scheduled reports, use the email command. show email Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display email values: root@localhost# show email Email Server: example-email.domain.com Mail Alarm: enabled Alarm Recipients: admin@domain.com another_admin@domain.
show entity To display the serial number and the values of the entity MIB entPhysicalAlias and entPhysicalAssetID, use the show entity command. show entity Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
show ftp To display the FTP server and directory for storing scheduled reports configuration, use the show ftp command. show ftp Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display the FTP server configuration: root@localhost# show ftp FTP settings: Server: my.ftp-server.
show hosts To display the hosts entries, use the show hosts command. show hosts Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display the hosts entries: Root@localhost# show hosts # $Id: hosts,v 1.5 2003/08/07 01:47:51 pwildi Exp $ # 127.0.0.1 localhost localhost.localdomain 10.10.10.2 trifecta-p2c-30.cisco.com trifecta-p2c-30 1.1.1.1 trifecta-p2c-30.cisco.
show interface management-port To display the configuration and statistics of management interface, use the show interface management-port command. This command is added in NAM 6.0(1). show interface management-port Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display the configuration and statistics of management interface: root@nam.
show internal resources monitoring To display the resources used for monitor features, use the show internal resources monitoring command. This command is added in NAM 6.0(2). show internal resources monitoring Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display the resources used for monitor features: root@nam.
Sensor threads RTP streams per thread Total RTP streams : : : 3 60000 180000 (160 bytes each) Conversation Records Conversation Records (PA) Host Records Site Records Site Matrix Records Data Source Records ART Records ART Records (PA) ART Server Records ART Client Records RTP stream records RTP MOS records Voice records : : : : : : : : : : : : : 600000 (192 bytes each) 100000 300000 (152 bytes each) 40000 (152 bytes each) 80000 (52 bytes each) 30000 (116 bytes each) 600000 (428 bytes each) 100000 1000
show inventory To display the system inventory information for a NAM device, use the show inventory command. show inventory Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes Command mode Usage Guidelines The show inventory command allows you to view the UDI for a NAM device. This identity information is stored in the NAM device’s non-volatile memory.
show ip To display the NAM IP parameters, use the show ip command. show ip Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display the NAM IP parameters: Root@localhost# show IP address: Subnet mask: IP Broadcast: DNS Name: Default Gateway: Nameserver(s): HTTP server: HTTP secure server: HTTP port: HTTP secure port: TACACS+ configured: Telnet: SSH: ip 101.10.11.189 255.255.255.
ip http secure server ip http tacacs+ Cisco Prime Network Analysis Module Command Reference Guide Page 179
show license To display the information about the license installed on the WAE device. show license Note This command is not valid for NAM-1, NAM-2, NME-NAM-80S, NME-NAM-120S, or the Cisco NAM 2200 Series appliances. Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Usage Guidelines This command is valid only on the NAM Virtual Blade.
show local-storage all To show all physical disks and virtual drives, use the show local-storage all command. show local-storage all Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
Device Id: 0 Sequence Number: 2 Media Error Count: 0 Other Error Count: 0 Predictive Failure Count: 0 Last Predictive Failure Event Seq Number: 0 PD Type: SATA Raw Size: 931.512 GB [0x74706db0 Sectors] Non Coerced Size: 931.012 GB [0x74606db0 Sectors] Coerced Size: 930.
Number Of Drives : 6 Span Depth : 1 Default Cache Policy: WriteThrough, ReadAhead, Direct, No Write Cache if Bad BBU Current Cache Policy: WriteThrough, ReadAheadNone, Direct, No Write Cache if Bad BBU Access Policy : Read/Write Disk Cache Policy : Disk's Default Encryption Type : None Physical Disk Information: Physical Disk: 0 Enclosure Device ID: 64 Slot Number: 7 Enclosure position: 0 Device Id: 7 Sequence Number: 2 Media Error Count: 0 Other Error Count: 0 Predictive Failure Count: 0 Last Predictive Fa
Device Id: 5 Sequence Number: 2 Media Error Count: 0 Other Error Count: 0 Predictive Failure Count: 0 Last Predictive Failure Event Seq Number: 0 PD Type: SATA Raw Size: 931.512 GB [0x74706db0 Sectors] Non Coerced Size: 931.012 GB [0x74606db0 Sectors] Coerced Size: 930.
Connected Port Number: 3(path0) Inquiry Data: 9XG102M3ST91000640NS FDE Capable: Not Capable FDE Enable: Disable Secured: Unsecured Locked: Unlocked Needs EKM Attention: No Foreign State: None Device Speed: 6.0Gb/s Link Speed: 6.
show local-storage physical To show physical drive information for local disks, use the show local-storage physcial command. show local-storage physical Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
Media Error Count: 0 Other Error Count: 0 Predictive Failure Count: 0 Last Predictive Failure Event Seq Number: 0 PD Type: SATA Raw Size: 931.512 GB [0x74706db0 Sectors] Non Coerced Size: 931.012 GB [0x74606db0 Sectors] Coerced Size: 930.
Secured: Unsecured Locked: Unlocked Needs EKM Attention: No Foreign State: None Device Speed: 6.0Gb/s Link Speed: 6.0Gb/s Media Type: Hard Disk Device Drive: Not Certified Drive Temperature :30 Celsius Enclosure Device ID: 64 Slot Number: 4 Enclosure position: 0 Device Id: 4 Sequence Number: 2 Media Error Count: 0 Other Error Count: 0 Predictive Failure Count: 0 Last Predictive Failure Event Seq Number: 0 PD Type: SATA Raw Size: 931.512 GB [0x74706db0 Sectors] Non Coerced Size: 931.
Sequence Number: 2 Media Error Count: 0 Other Error Count: 0 Predictive Failure Count: 0 Last Predictive Failure Event Seq Number: 0 PD Type: SATA Raw Size: 931.512 GB [0x74706db0 Sectors] Non Coerced Size: 931.012 GB [0x74606db0 Sectors] Coerced Size: 930.
show local-storage progress To show RAID array construction or deconstruction progress for local disks, use the show local-storage progress command. show local-storage progress Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
show local-storage virtual To how to display virtual drive (RAID array) information for local disks, use the show local-storage virtual command. show local-storage virtual Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
show local-storage physical show local-storage progress Cisco Prime Network Analysis Module Command Reference Guide Page 192
show log config To display the maintenance image configuration import log entries, use the show log config command. show log config Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
show log patch To display the patch log entries, use the show log patch command. show log patch Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
show log report To display the import log entries, use the show log report command. show log report Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
show log upgrade To display the maintenance image upgrade log entries, use the show log upgrade command. show log upgrade Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display the maintenance image upgrade entries: Root@localhost# show log upgrade Fri Aug 23 10:32:27 2002 : path: ftp://namlab-pc1/pub/rmon/MP-KPLUS Fri Aug 23 10:32:27 2002 : file: mp-dev.1-2-0-5.
show memory To display the installed memory, available memory, and the memory being used by the system, use the show memory command. show memory Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
show metric export To show metric export configuration, use the show metric export command. show metric export Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes Command mode Examples The following example shows the metric export configuration: root@nam.cisco.com# show metric export Metric export: enabled Host: 10.0.0.
show monitor protocol encapsulation To display the encapsulation configurations, use the show monitor protocol encapsulation command. This command is removed in NAM 6.0(1) show monitor protocol encapsulation Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display the encapsulation configurations: root@nam.cisco.
show monitor protocol all To display all of the protocols in the protocol directory, use the show monitor protocol all command. This command is removed in NAM 6.0(1). show monitor protocol all Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Usage Guidelines This command is supported on all NAM platforms.
show monitor rtp-stream To display the RTP monitoring and alarm threshold settings, use the show monitor rtp-stream command. show monitor rtp-stream Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display the RTP-stream monitoring settings and alarm thresholds.
show monitor rtp-stream filter To display the URL collection configuration, use the show monitor rtp-stream filter command. show monitor rtp-stream filter Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
show monitor urlcollection To display the URL collection configuration, use the show monitor urlcollection command. show monitor urlcollection Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
show monitor urlfilter To display the URL filter configuration, use the show monitor urlfilter command. This command is removed in NAM 6.0(1). show monitor urlfilter [control-index] Syntax Description control-index (Optional) Specifies the URL filter control index. Syntax Description Defaults This command has no default settings.
6: NAM CLI Commands: show password strong-policy - web user ___________________________________________ This chapter describes the following NAM CLI commands: show password strong-policy show patches show pkt-drop counters show preferences show protocol-feature show remote-storage show rxcounters show snmp show syslog-settings show system-alerts show tech-support show time show time ptp show trap-dest show version show waas data-source show
trap-dest upgrade waas export server-filter-list waas import server-filter-list waas server filter web-publication web-user Cisco Prime Network Analysis Module Command Reference Guide Page 206
show password strong-policy To display the strong password policy settings for user names, use the show password strong-policy command. show password strong-policy Defaults This command has no default settings. Command Modes Command mode Usage Guidelines There are only two valid users, root and guest. Examples This example shows how to set a password: root@localhost.cisco.com# show password strong-policy Strong password policy is enabled.
show patches To display all of the installed patches, use the show patches command. show patches Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
show pkt-drop counters To display the NAM hardware, flow manager, and the metrics engine drop, use the show pkt-drop counters command. show pkt-drop counters Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
show preferences To display the configured preferences for your screen, use the show preferences command. show preferences Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display the configured screen preferences: root@localhost.cisco.
show protocol-feature To display the parsing protocol feature, use the show protocol-feature command. show protocol-feature Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display the parsing protocol feature: root@NAM.cisco.
show remote-storage To display the network storage target for report and capture date, use the show remote-storage command. show remote-storage Syntax Description This command has no keywords or arguments. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display the web user information: root@localhost.cisco.
show rxcounters To display the number of packets received by NAM data ports, use the show rxcounters command. show rxcounters Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display the number of packets received by NAM data ports: root@nam235Cat6k.cisco.com# show rxcounters data port 1 rx pkt count: 193327281 data port 2 rx pkt count: 1164 root@nam235Cat6k.cisco.
show snmp To display the SNMP parameters, use the show snmp command. show snmp Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display the SNMP parameters: Root@localhost# show snmp SNMP Agent: mynam.cisco.com 209.265.200.225 SNMPv1: Enabled SNMPv2C: Enabled SNMPv3: Disabled community community private write public read trap community trap community public public 112.10.17.
show syslog-settings To display the NAM system log settings, use the show syslog-settings command. show syslog-settings Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display the NAM system log settings: root@localhost# show syslog-settings Remote server 1: 172.20.98.177 Remote server 2: 10.0.0.
show system-alerts To display NAM failures or problems, use the show system-alerts command. show system-alerts Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
show tech-support To display technical support information, use the show tech-support command. show tech-support Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
show time To display NAM time zone or time synchronization settings, use the show time command. show time Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
show time ptp To display PTP specific time settings, use the show time ptp command. This command is removed in NAM 6.0(1). show time ptp Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Usage Guidelines When you enter the command, the following commands are available: clock—Displays PTP clock information. foreign-master-record—Displays PTP foreign master records. parent - Displays PTP parent properties.
show trap-dest To display all of the NAM trap destinations, use the show trap-dest command. show trap-dest [trap-index] Syntax Description trap-index (Optional) Displays the trap destinations by the specified trap index. Syntax Description Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display the NAM trap destinations: Root@localhost# show trap-dest Trap index: 23370 Community: public Address: 172.20.98.
-v (Optional) Sets the output to verbose. -m max_ttl (Optional) Sets the maximum time-to-live (max number of hops) used. -p port (Optional) Sets the base UDP port number used in probes. -s src_addr (Optional) Forces the source address to be an address other than the IP address of the interface the packet is sent on. -w waittime (Optional) Sets the time (in seconds) to wait for a response to a probe. Syntax Description Defaults This command has no default settings.
show top-memory-users To display the NAM top memory users, use the show top-memory-users command. This command is added in NAM 6.0(1). show top-memory-users Syntax Description This command has no keywords or arguments. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display the NAM top memory users: root@nam.localdomain# show top-memory-users Top memory usage information not available. root@nam.
show version To display the NAM version information, use the show version command. show version Syntax Description This command has no keywords or arguments. Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to display the NAM version information: Root@localhost# show version NAM application image version: 5.0(1T.45) INTERIM SOFTWARE Helper Version: 1.1(0.19) Gold Helper Version: 1.1(0.
show waas data-source To display the WAAS devices configured on the NAM device, use the show waas data-source command. show waas data-source [datasrc-index] Syntax Description datasrc-index (Optional) Displays the data source index Syntax Description Defaults The default behavior is to show all WAAS data sources unless a specific data source index is specified. Command Modes Command mode Usage Guidelines This command is supported on all NAM platforms.
show waas device To display the WAAS devices configured on the NAM device, use the show waas device command. show waas device [ip-address] Syntax Description ip-address IP address of the WAAS device (optional) Syntax Description Defaults The default behavior is to show all WAAS devices unless IP address is specified. Command Modes Command mode Usage Guidelines This command is supported on all NAM platforms. Examples The following example shows the system inventory information: root@nam.cisco.
show waas server filter To show WAAS server filter list, use the show waas server filter command. show waas server filter Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Examples The following example shows how to display the waas server filters. root@nam.cisco.com# show waas server filter 10.0.0.
show web-publication To display the web publication hosts configuration information, use the show web-publication command. show web-publication Syntax Description This command has no keywords or arguments. Defaults This command has no default settings.
show web-user To display the web user information, use the show web-user command. show web-user [username] Syntax Description username (Optional) Displays the specified user name information. Syntax Description Defaults This command has no default settings.
shutdown To shut down the NAM, use the shutdown command. shutdown Syntax Description This command has no arguments or keywords. Defaults This command has no default settings.
snmp To configure NAM system MIB objects, use the snmp command. snmp community community-string { ro | rw } snmp delete community community-string snmp contact contact-string snmp location location-string snmp name name-string Syntax Description community community-string ro | rw Sets the device community string. delete community-string Deletes the device community string. contact contact-string Sets the device contact string. location location-string Sets the device location.
syslog To enter the system log subcommand mode, and then configure system logging for the NAM, use the syslog command. syslog Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes Command mode Usage Guidelines When you enter the system log subcommand mode, the following commands are available: cancel—Discards changes and exits from the subcommand mode. exit—Saves changes and exits from the subcommand mode; see the exit command.
syslog remote-server To capture NAM remote server alarms, use the remote-server subcommand from the syslog subcommand mode. remote-server disable | [server1 [server2] [server3] [server4] [server5] Syntax Description disable Disables remote server event logging. server1 server2 server3 server4 server5 (Optional) Specifies the remote server. Syntax Description Defaults This command has no default settings.
web-user Cisco Prime Network Analysis Module Command Reference Guide Page 233
terminal To set the number of lines on a screen for this session, use the terminal command. terminal editor [enable | disable] terminal length length terminal mode { 0 | 1} Syntax Description editor [enable | disable] (Optional) Enables or disables the NAM CLI command editing. length length Sets the number of lines per screen for a session. mode { 0 | 1} Sets the terminal mode. Syntax Description Defaults This command has no default settings.
time To enter the time configuration subcommand mode, and then configure NAM system time settings, use the time command. time Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Types Switch command Command Modes Privileged Usage Guidelines When you enter the time configuration subcommand mode, the following commands are available: cancel—Discards changes and exits from the subcommand mode.
help - display help ptp-ip-address - set the ip address of the ptp interface sync - synchronize NAM system time with switch or ntp root@hostname.cisco.com(sub-time)# sync switch root@hostname.cisco.com(sub-time)# exit Successfully updated NAM system time settings. NOTE:You have configured the NAM synchronize time to the switch. For this change to take effect, set the time from the switch or reset the NAM. root@hostname.cisco.
traceroute To trace the route to a IPv4 network device, use the traceroute command. traceroute [-I | n | v] [-f first_ttl] [-m max_ttl] [-p port] [-s src_addr] [-t tos] [-w waittime] destination host name | IP address [packetlen] Syntax Description -I (Optional) Specifies that ICMP ECHO is used instead of UDP datagrams. -n (Optional) Prints hop addresses numerically. -v (Optional) Sets the output to verbose. -f first_ttl (Optional) Sets the initial time-to-live used in the first outgoing packet.
Syntax Description Defaults This command has no default settings. Command Modes Command mode Examples This example shows how to trace a route to a network device named aragon: root@localhost.cisco.com# traceroute -I -n -v -f first_ttl -p 5 -w 10 aragon 123.34.54.12 root@localhost.cisco.
traceroute6 To trace the route to a IPv6 network device, use the traceroute6 command. This command is added in NAM 6.0(1). traceroute [ n | v] [-m max_ttl] [-p port] [-s src_addr] [-w waittime] destination host name | IPv6 address Syntax Description -n (Optional) Prints hop addresses numerically. -v (Optional) Sets the output to verbose. -m max_ttl (Optional) Sets the maximum time-to-live (max number of hops) used. -p port (Optional) Sets the base UDP port number used in probes.
trap-dest To enter the trap destination subcommand mode and create or edit trap destinations on the NAM, use the trap-dest command. To remove a trap destination entry, use the no form of this command. trap-dest no trap-dest [control-index] Syntax Description control-index (Optional) Specifies the collection control index. Range is from 1 to 65535. Syntax Description Defaults This command has no default settings.
Examples This example shows how to configure traps on the NAM: root@hostname.cisco.com# trap-dest Entering into subcommand mode for this command. Type 'exit' to come out of this mode. Type 'cancel' to discard changes and to come out of this mode. root@hostname.cisco.
upgrade To download and install a new maintenance/application image on the NAM, use the upgrade command. upgrade ftp://user:passwd@host/full-path/filename reformat Syntax Description ftp://user:passwd@host/full-path/filen Path to the location of the upgrade ame maintenance image. reformat (Optional) Reformat the existing installation. All configuration and data will be lost. This command is the same as option 2 (-install) in the helper utility.
waas export server-filter-list To export WAAS server filter list to a remote host, use the waas export server-filter-list command. waas export server-filter-list ftp://@/ Syntax Description ftp://@/ Specifies the remote location reachable by ftp. Syntax Description Defaults This command has no default settings.
waas import server-filter-list To import the WAAS server filter list from a remote host, use the waas import server-filter-list command. waas import server-filter-list ftp://@// Syntax Description ftp://@/ Specifies the remote location reachable by ftp. Syntax Description Defaults This command has no default settings.
waas server filter To add a WAAS server filter, use the waas import server-filter command. To remove a server filter, use the no form of this command waas server filter no waas server filter Syntax Description ip-address Specifes IPV4 of the WAAS server Syntax Description Defaults This command has no default settings. Command Modes Command mode Examples The following example shows how to add a WAAS server filter and how to remove a WAAS server filter: root@nam.cisco.
web-publication To enable and set up a list of hosts that can view the NAM GUI monitoring displays without logging into the NAM, use the web-publication command. To remove web publishing from your configuration, use the no form of this command. web-publication username no web-publication Syntax Description username Sets the username. Syntax Description Defaults This command has no default settings.
Examples This example shows how to configure a host to receive web published reports from the NAM: root@hostname.cisco.com# web-publication Entering into subcommand mode for this command. Type 'exit' to come out of this mode. Type 'cancel' to discard changes and to come out of this mode. root@hostname.cisco.com(sub-web-publication)# ? root@hostname.cisco.
web-user To enter the web user configuration subcommand mode, and then configure local web users on the NAM, use the web-user command. To remove a web user from your configuration, use the no form of this command. web-user no web-user username Syntax Description username Sets the username. Syntax Description Defaults This command has no default settings.
Examples This example shows how to configure a NAM web user: root@hostname.cisco.com# web-user Entering into subcommand mode for this command. Type 'exit' to come out of this mode. Type 'cancel' to discard changes and to come out of this mode. root@hostname.cisco.
Appendix A NAM Maintenance Partition CLI ___________________________________________ Table A-1 lists the Network Analysis Module maintenance partition commands. Table A-1 NAM Maintenance Image CLI Command Usage ip address address mask Sets the NAM IP address. ip broadcast broadcast-address Sets the NAM broadcast address. ip gateway gateway-address Sets the NAM gateway address. ip nameserver DNS-server-address1 [DNS-server-address2 [DNS-server-address3]] Sets up to three DNS server addresses.
logout Exits the current session. exit Exits the current session. passwd-guest Sets the password for the guest account. enable-guest Enables the guest account. disable-guest Disables the guest account. reset Reboots the NAM (available in guest account only). upgrade-bios Installs a new BIOS image (available in guest account only).
Appendix B Acronyms ___________________________________________ Table B-1 defines the acronyms used in this publication.
MAC Media Access Control MD5 message digest 5 MFD multicast fast drop MGCP Media Gateway Control Protocol MIB Management Information Base MII media-independent interface MPLS Multiprotocol Label Switching MTU maximum transmission unit NAM Network Analysis Module NDE NetFlow Data Export NetBIOS Network Basic Input/Output System NTP Network Time Protocol PC Personal Computer (formerly PCMCIA) PHY physical sublayer PTP Precision Time Protocol (1588) QoS quality of service RCP R
SPAN Switched Port Analyzer SRE Services Ready Engine SSL Secure Sockets Layer SVC switched virtual circuit TACACS+ Terminal Access Controller Access Control System Plus TCP/IP Transmission Control Protocol/Internet Protocol TFTP Trivial File Transfer Protocol TOS type of service TTL Time To Live UDP User Datagram Protocol UTC Coordinated Universal Time VACL VLAN access control list VLAN virtual LAN VPN virtual private network VTP VLAN Trunking Protocol WAAS Wide Area Applicat
