Release Notes

ManualsBrandsCisco ManualsSwitchesCisco ESW2-350G-52 Advanced Managed Switch

Release Notes for 200, 300, 500, and ESW2 Series Switches Firmware Version 1.3.0.62 1

Release Notes

Release Notes for 200, 300, 500, and ESW2

Series Switches Software Version 1.3.0.62

May 2013

These Release Notes describe the recommended practices and known issues

that apply to the Version 1.3.0.62 software for the following products:

Model Description Ports

SF200-24 24-Port 10/100 Smart Switch e1-e24, g1-g2

SF200-24P 24-Port 10/100 PoE Smart Switch e1-e24, g1-g2

SF200-48 48-Port 10/100 Smart Switch e1-e48, g1-g2

SF200-48P 48-Port 10/100 PoE Smart Switch e1-e48, g1-g2

SG200-18 18-port Gigabit Smart Switch g1-g18

SG200-26 26-port Gigabit Smart Switch g1-g26

SG200-26P 26-port Gigabit PoE Smart Switch g1-g26

SG200-50 50-port Gigabit Smart Switch g1-g50

SG200-50P 50-port Gigabit PoE Smart Switch g1-g50

SG300-10 10-port Gigabit Managed Switch g1-g10

SG300-10MP 10-port Gigabit PoE Managed Switch g1-g10

SG300-10SFP 10-port Gigabit PoE Managed Switch 8 SFP + 2 Combo slots

SG300-10P 10-port Gigabit PoE Managed Switch g1-g10

SG300-20 20-port Gigabit Managed Switch g1-g20

Summary of content (17 pages)

PAGE 1
Release Notes Release Notes for 200, 300, 500, and ESW2 Series Switches Software Version 1.3.0.62 May 2013 These Release Notes describe the recommended practices and known issues that apply to the Version 1.3.0.
PAGE 2
Release Notes Model Description Ports SG300-28 28-port Gigabit Managed Switch g1-g28 SG300-28P 28-port Gigabit PoE Managed Switch g1-g28 SG300-28MP 28-port Gigabit Max PoE Managed Switch g1-g28 SG300-52 52-port Gigabit Managed Switch g1-g52 SG300-52P 52-port Gigabit PoE Managed Switch g1-g52 SG300-52MP 52-port Gigabit Max PoE Managed Switch g1-g52 SF300-08 8-port 10/100 Managed Switch e1-e8 SF302-08 8-port 10/100 Managed Switch e1-e8, g1-g2 SF302-08MP 8-port 10/100 PoE Managed S
PAGE 3
Release Notes Model Description Ports SF500-48 48-port 10/100 Stackable Managed Switch e1-e48, g1-g4 48-port 10/100 PoE Stackable Managed Switch e1-e48, g1-g4 28-port 10/100/1000 Stackable Managed Switch g1-g28 28-port 10/100/1000 PoE Stackable Managed Switch g1-g28 52-port 10/100/1000 Stackable Managed Switch g1-g52 52-port 10/100/1000 PoE Stackable Managed Switch g1-g52 24-port 10/100/1000 Stackable Managed Switch g1-g24, xg1-xg4 24-port 10/100/1000 PoE Stackable Managed Switch g1-g24,
PAGE 4
Release Notes Model Description Ports SG500X-48P 48-port 10/100/1000 PoE Stackable Managed Switch g1-g48, xg1-xg4 ESW2-350G52DC 52-port Gigabit Managed Switch g1-g52 ESW2-550X48DC 48-port 10/100/1000 Stackable Managed Switch g1-g48, xg1-xg4 4 10 Gigabit Ethernet SFP+ (1/5/10GE SFP+ modules) 4 10 Gigabit Ethernet SFP+ (1/5/10GE SFP+ modules) NOTE *For the Sx500 Series, each combo mini-GBIC port has one 10/100/1000 copper Ethernet port and one mini-GBIC/SFP Gigabit Ethernet slot, with one port
PAGE 5
Release Notes Contents Hardware Versions, page 5 Major Changes and Defects Corrected, page 7 Limitations and Restrictions, page 9 Where to Find Support, page 17 Hardware Versions The Release 1.3.0.62 firmware runs on two different versions of hardware for the 200 Series Smart Switches, and the 300 Series Managed Switches. There is a single version of hardware for the 500and ESW2 series switches.
PAGE 6
Release Notes V1 versus V2 Hardware Total Number of MAC Addresses Total Number of Active VLANs Total Number of Multicast Groups Sx300 in Firmware 1.1.x and above. HW VID=02 16K 4K 1K Sx500, SG500X and ESW2 switches have a single version of HW, see the admin guide for details. To determine which version of hardware you are using, click Status > System Summary. Look at the lower portion of the screen under the graphic representation of the switch for the PID VID.
PAGE 7
Release Notes Major Changes and Defects Corrected Major Changes • Added support for RMON History, Events and Alarms for the 200 Series Switches. • Added Basic Hybrid and Advanced Hybrid modes for stacking. Increased the number of units in a Hybrid stack up to 8. • Added Unicast SNTP Server time synchronization. • Added the SCP option for the 200 Series Switches.
PAGE 8
Release Notes issue does not occur on the CLI, because the CLI will not permit two ACE to be created on one ACL. (CQ147329) 8 • After a static IPv4 route is configured on Sx300, this route is not displayed on WEB GUI though this route works fine. However, it can successfully be displayed in CLI, and it does not matter whether this route was created via CLI or GUI. (CQ147056) • After the firmware is upgraded from 1.2.9.44 to 1.3.0, the IP default gateway changes to default route.
PAGE 9
Release Notes Limitations and Restrictions The following caveats are acknowledged in release 1.3.0.62: Problem: In switch mode although multiple default gateways can be configured through CLI, only the gateway with lowest value can be active. Hence, switches should not allow the CLI to configure multiple default gateways. Solution: When modifying the default gateway through CLI, delete the old one first.
PAGE 10
Release Notes The following caveats are carried forward from release 1.3.0.59: Problem: Some of the pages in the web-based interface require the Java Runtime Environment (JRE) to be installed, otherwise they may display incorrectly. Solution: Install the latest JRE. Problem: Granularity of traffic shaping on the following Uplink ports starts with 2Mbps and not with 64Kbps. When configuring traffic shaping on these ports to rates lower than 2Mbps, the actual traffic shaping rate will be 2Mbps.
PAGE 11
Release Notes Problem: When a PoE switch is connected to another PoE switch, one of the switches overcomes the internal power supply of the other PoE switch, so the other PoE switch cannot provide PoE power to powered devices. If the connection between these switches is removed, the switch that received power from the other switch will momentarily lose its power and reboot. (CQ135360, CQ138875) Solution: Disable PoE on the ports connecting the two PoE switches.
PAGE 12
Release Notes Problem: Some WEB GUI pages require full version compatibility of JRE, Browser and JRE-Browser applets. For XML compatibility reasons, MSXML DLL Version 6 is required for IE browser users. Solution: For download and installation please refer the following link: www.microsoft.com/downloads/details.aspx?FamilyID=993C0BCF-3BCF4009-BE21-27E85E1857B1&displaylang=en Problem: Notification Recipients table entry becomes un-editable with an incorrect or missing parameter.
PAGE 13
Release Notes Problem: Egress rate shaping does not work as expected. Configuring egress shape on Gigabit ports or on Combo ports between 64k to 5000k, will always result in 2 Million Bits. This is resolved with the new hardware release 1.1.1.8. It still exists on HW V01. It also does not work on SG300-52/52P & SG200-52/52P switches. (CQ123397 and CQ130715) Solution: There is no workaround.
PAGE 14
Release Notes Problem: When managing stacking switches through the web-based interface, the loading time on the following web pages is more than 10 seconds: (CQ143851) • Status and Statistics • Port Management • VLAN Management • Access Control • Quality of Service Solution: Use the command line interface instead. Problem: When the current master unit is already set to auto-numbering, reconfiguring it as 'auto' does not work.
PAGE 15
Release Notes Problem: There is a problem using PoE auto control via time-range. After performing a save and reboot, the saved time-range configuration on port 4 is also displayed on port 5 and 6. (CQ146121) Solution: There is no workaround. Problem: If you modify an IPv6 tunnel configuration, the change will not take effect until you perform a shut then no shut on the tunnel interface. (CQ146071) Solution: effect.
PAGE 16
Release Notes STEP 1 Open the Administration > Routing Resources page. STEP 2 Adjust the IPv6 entry from the default value to 8, then apply and reboot the switch to take effect. STEP 3 After the switch boots up, configure IPv4 entry to 1800, then apply and reboot. STEP 4 The backup switch will reboot repeatedly, other stack members work as expected. Solution: Adjust the IPv4 and IPv6 router resources at the same time.
PAGE 17
Release Notes Where to Find Support To obtain current support information for Cisco Small Business products, visit the following URLs: www.cisco.com/cisco/web/solutions/small_business/products/ routers_switches/500_series_switches/index.html www.cisco.com/cisco/web/solutions/small_business/products/ routers_switches/300_series_switches/index.html www.cisco.com/cisco/web/solutions/small_business/products/ routers_switches/200_series_switches/index.html www.cisco.