Datasheet

ManualsBrandsCisco ManualsNetworkingCWDM-SFP-1510=

Corporate Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Cisco CWDM GBIC and CWDM SFP

Installation Note

Product Numbers:

This installation note contains instructions for installing Coarse Wave Division Multiplexer (CWDM)

Gigabit Interface Converter (GBIC) laser optical transceiver modules and CWDM Small Form-Factor

Pluggable (SFP) laser optical transceiver modules enabling your system to connect to a Cisco CWDM

network.

Contents

This installation note contains the following sections:

• Overview, page 2

• Installing and Removing CWDM GBICs and CWDM SFPs, page 4

• Connecting to the CWDM Passive Optical System, page 8

• Related Documentation, page 9

• Obtaining Documentation, page 9

• Obtaining Technical Assistance, page 11

• Obtaining Additional Publications and Information, page 12

CWDM-GBIC-1470= CWDM-GBIC-1550= CWDM-SFP-1470= CWDM-SFP-1550=

CWDM-GBIC-1490= CWDM-GBIC-1570= CWDM-SFP-1490= CWDM-SFP-1570=

CWDM-GBIC-1510= CWDM-GBIC-1590= CWDM-SFP-1510= CWDM-SFP-1590=

CWDM-GBIC-1530= CWDM-GBIC-1610= CWDM-SFP-1530= CWDM-SFP-1610=

Summary of content (14 pages)

PAGE 1
Cisco CWDM GBIC and CWDM SFP Installation Note Product Numbers: , CWDM-GBIC-1470= CWDM-GBIC-1550= CWDM-SFP-1470= CWDM-SFP-1550= CWDM-GBIC-1490= CWDM-GBIC-1570= CWDM-SFP-1490= CWDM-SFP-1570= CWDM-GBIC-1510= CWDM-GBIC-1590= CWDM-SFP-1510= CWDM-SFP-1590= CWDM-GBIC-1530= CWDM-GBIC-1610= CWDM-SFP-1530= CWDM-SFP-1610= This installation note contains instructions for installing Coarse Wave Division Multiplexer (CWDM) Gigabit Interface Converter (GBIC) laser optical transceiver modules and CWDM Sma
PAGE 2
Overview Overview The CWDM GBICs are hot-swappable, transceiver components that you can plug into IEEE 802.3z standard receptacles in Cisco routers and switches and convert Gigabit Ethernet electrical signals into a single-mode fiber-optic (SMF) interface. You can connect the CWDM GBICs to CWDM passive optical system optical add/drop multiplexer (OADM) or multiplexer/demultiplexer plug-in modules using single-mode fiber-optic cables with standard SC connectors.
PAGE 3
Overview Figure 2 CWDM SFP Module (Yellow-Coded CWDM-SFP-1550= Shown) C C WD l L as M N S # s -S /N 50 1 F : 7 21 PO / C 14 H 01 F 7 1 R 0 2 1 3 0 2 3 4 G 4 0 5 . 6 0 1 3 0 -1 3 1 5 2 94071 3 4 1 Color arrow on label 4 Color coded bale clasp 2 Receive optical bore 5 Optical bore dust plug 3 Transmit optical bore — — Both the CWDM GBICs and CWDM SFPs come in eight wavelengths that range from 1470 nm to 1610 nm.
PAGE 4
Installing and Removing CWDM GBICs and CWDM SFPs Installing and Removing CWDM GBICs and CWDM SFPs This section describes how to install and remove CWDM GBICs and CWDM SFPs. This section also contains guidelines for handling the CWDM GBICs and CWDM SFPs.
PAGE 5
Installing and Removing CWDM GBICs and CWDM SFPs Installing a CWDM GBIC To install a CWDM GBIC, use Figure 3 as a reference and follow these steps: Step 1 Remove the CWDM GBIC from its protective packaging, and verify that the CWDM GBIC is the correct model for your network configuration. Note You can identify CWDM GBICs by the color dot on the GBIC body and by the color band on the GBIC label, which also lists the CWDM GBIC model number and wavelength. (See Figure 1 and Table 1.
PAGE 6
Installing and Removing CWDM GBICs and CWDM SFPs Removing a CWDM GBIC Warning Because invisible radiation may be emitted from the aperture of the port when no fiber cable is connected, avoid exposure to radiation and do not stare into open apertures. To remove a CWDM GBIC, use Figure 4 as a reference and follow these steps: Step 1 Tip Disconnect any fiber-optic cable from the CWDM GBIC, and install dust plugs in the optical bores of the CWDM GBIC and dust caps on the fiber-optic cable connectors.
PAGE 7
Installing and Removing CWDM GBICs and CWDM SFPs Installing a CWDM SFP Module To install a CWDM SFP module, use Figure 5 as a reference and follow these steps: Step 1 Remove the CWDM SFP module from its protective packaging, and verify that the CWDM SFP module is the correct model for your network configuration. Note You can identify CWDM SFP modules by the color arrow on the CWDM SFP module label, which also lists the SFP model number and wavelength, and by the color bar on the bale clasp.
PAGE 8
Connecting to the CWDM Passive Optical System Removing a CWDM SFP Module To remove a CWDM SFP module, use Figure 6 as a reference and follow these steps: Step 1 Disconnect the fiber-optic connector cable from the CWDM SFP module. Step 2 Pivot the bale out and down to eject the CWDM SFP module. If the bale-clasp latch is obstructed and you cannot use your index finger to open it, use a small, flat-blade screwdriver or other long, narrow instrument to open the bale-clasp latch.
PAGE 9
Related Documentation Related Documentation For more information about CWDM GBIC solution deployment, refer to the following related documentation: • Cisco GBIC Solution, Data Sheet • Cisco GBIC Solution, Q & A • Installation Note for the CWDM Passive Optical System • Regulatory Compliance and Safety Information for the Catalyst 6500 Series Switch For more information about Cisco GBICs, refer to the information at the following URL: http://www.cisco.
PAGE 10
Obtaining Documentation Documentation CD-ROM Cisco documentation and additional literature are available in a Cisco Documentation CD-ROM package, which may have shipped with your product. The Documentation CD-ROM is updated regularly and may be more current than printed documentation. The CD-ROM package is available as a single unit or through an annual or quarterly subscription. Registered Cisco.
PAGE 11
Obtaining Technical Assistance Obtaining Technical Assistance Cisco provides Cisco.com, which includes the Cisco Technical Assistance Center (TAC) website, as a starting point for all technical assistance. Customers and partners can obtain online documentation, troubleshooting tips, and sample configurations from the Cisco TAC website. Cisco.com registered users have complete access to the technical support resources on the Cisco TAC website, including TAC tools and utilities. Cisco.com Cisco.
PAGE 12
Obtaining Additional Publications and Information Cisco TAC Website The Cisco TAC website provides online documents and tools to help troubleshoot and resolve technical issues with Cisco products and technologies. To access the Cisco TAC website, go to this URL: http://www.cisco.com/tac All customers, partners, and resellers who have a valid Cisco service contract have complete access to the technical support resources on the Cisco TAC website. Some services on the Cisco TAC website require a Cisco.
PAGE 13
Obtaining Additional Publications and Information • Packet magazine is the Cisco quarterly publication that provides the latest networking trends, technology breakthroughs, and Cisco products and solutions to help industry professionals get the most from their networking investment. Included are networking deployment and troubleshooting tips, configuration examples, customer case studies, tutorials and training, certification information, and links to numerous in-depth online resources.
PAGE 14
Obtaining Additional Publications and Information This document is to be used in conjunction with the publications described in the “Related Documentation” section, as well as other documents that support your specific router or switch. CCIP, CCSP, the Cisco Arrow logo, the Cisco Powered Network mark, Cisco Unity, Follow Me Browsing, FormShare, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.