Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
Preface This preface describes the objectives, audience, organization, and conventions of this guide, and describes related documents that have additional information.
Preface Organization This guide is organized into the following chapters and appendix. Chapter 1, “Product Overview” Briefly describes the router models and the hardware features available. Chapter 2, “Installing the Router” Lists the items shipped with the router, the equipment and tools necessary for installing the router, the safety warnings and guidelines, and the procedures for installing the router.
Preface Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device.
Preface Avvertenza IMPORTANTI ISTRUZIONI SULLA SICUREZZA Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento.
Preface Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16193-03 vii
Preface Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.
Preface Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16193-03 ix
Preface Warning When installing the product, please use the provided or designated connection cables/power cables/AC adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the “UL” shown on the code) for any other electrical devices than products designated by CISCO.
Preface Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. SAVE THESE INSTRUCTIONS.
Preface Related Documentation In addition to the Cisco 860 series, Cisco 880 series, and Cisco 890 series ISR Hardware Installation Guide (this document), the Cisco 860 series, Cisco 880 series, and Cisco 890 series ISR documentation set includes the following documents: • Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers • Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Software Configuration Guide • Software Activation for
Preface Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0.
Preface Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide xiv OL-16193-03
CH A P T E R 1 Product Overview This chapter provides an overview of the features available for the Cisco 860 series, Cisco 880 series, and Cisco 890 series Integrated Services Routers (ISRs), and contains the following sections: • General Description, page 1-1 • Cisco 860 Series ISRs, page 1-2 • Cisco 880 Series ISRs, page 1-3 • Cisco 890 Series ISRs, page 1-11 • Hardware Features, page 1-13 Note For compliance and safety information, see Regulatory Compliance and Safety Information Roadmap th
Chapter 1 Product Overview Cisco 860 Series ISRs Cisco 860 Series ISRs The Cisco 860 series ISRs are fixed-configuration data routers that support the following features: • An integrated 4-port 10/100 Ethernet switch for connecting to the LAN • A10/100 Fast Ethernet (FE) or ADSL2 over POTs port for connecting to the WAN • Optional, embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless AP Figure 1-1 shows the front panel details of the Cisco 860 wireless router.
Chapter 1 Product Overview Cisco 880 Series ISRs Figure 1-2 shows the back panel details of the Cisco 861 wireless (861W) ISR. Nonwireless routers do not have antennas on the back panel. However, the feature locations are similar for all Cisco 860 series routers.
Chapter 1 Product Overview Cisco 880 Series ISRs This section contains the following topics: • Cisco 880 Series Data Routers, page 1-4 • Cisco 880 Series Voice Routers, page 1-7 Cisco 880 Series Data Routers The Cisco 880 series data routers provide integrated VPN, embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless AP, 3G, and backup capabilities. Figure 1-3 and Figure 1-4 show the features available on Cisco 880 series data routers.
Chapter 1 Product Overview Cisco 880 Series ISRs Figure 1-4 shows the back panel details of the Cisco 888W data router. Nonwireless routers do not have antennas on the back panel. However, the feature locations are similar across all Cisco 880 series data routers. Back Panel of the Cisco 888W Data Router 231951 Figure 1-4 1 2 3 4 5 6 7 8 1 ISDN port—not available on 3G models 6 PoE power connector—optional 2 Primary WAN port1—G.
Chapter 1 Product Overview Cisco 880 Series ISRs Figure 1-5 Back Panel of the Cisco 888E and Cisco 888E-W Data Router B RX/TX C RX 253233 A RX/TX 1 2 3 4 6 5 6 7 1 ISDN port—not available on 3G models 2 Primary WAN port1—RJ-45 only, G.
Chapter 1 Product Overview Cisco 880 Series ISRs Back Panel of the Cisco 888EG Data Router 253231 Figure 1-6 1 2 3 4 6 5 6 7 1 3G Diag port 2 Primary WAN port1—RJ-45 only, G.
Chapter 1 Product Overview Cisco 880 Series ISRs Figure 1-7 shows the front panel details of the Cisco 880 series wireless voice router.
Chapter 1 Product Overview Cisco 880 Series ISRs Figure 1-8 shows the back panel details of the Cisco 881SRST-W voice router.
Chapter 1 Product Overview Cisco 880 Series ISRs Figure 1-9 shows the back panel details of the Cisco 888SRST-W voice router. Back Panel of the Cisco C888SRST-W, Cisco IAD888EF, Cisco C888ESRST, and Cisco C888ESRST-W Voice RouterRouters 241905 Figure 1-9 2 1 2 6 3 4 5 7 8 9 10 1 Primary WAN port1—G.SHDSL, RJ-45 only on the C888ESRST-W.
Chapter 1 Product Overview Cisco 890 Series ISRs Back Panel of the Cisco IAD888EB Router 253230 Figure 1-10 1 2 3 4 5 6 7 8 9 10 1 Primary WAN port1—G.SHDSL 7 Serial port—console or auxiliary 2 Voice ports—four FXS/DID ports and one voice BRI port. 8 PoE power connector—optional 3 Voice ports—four FXS/DID ports and one voice BRI port. 9 Reset button 4 Primary WAN port—G.SHDSL, RJ-45 only on the C888ESRST-W.
Chapter 1 Product Overview Cisco 890 Series ISRs • DIMM expansion socket that can accept up to 512 MB of additional memory, for a total of 768 MB system memory • Three reverse-polarity threaded Neill-Concelman (RP-TNC) connectors on the back panel for non-captive dual-band WLAN antenna (wireless models only) • Supports the the AIM2-CUE-K9 and AIM2-APPRE-104-K9. The following feature is located on the front panel: • Two USB 1.
Chapter 1 Product Overview Hardware Features Figure 1-13 shows the back panel details of the Cisco 892-W router. Nonwireless routers do not have RP-TNC antenna or connectors on the back panel. Some of the features that are shown may not be available on your router. However, the feature locations are similar across all Cisco 890 series routers.
Chapter 1 Product Overview Hardware Features • 3G Cellular Data WAN Connectivity • Wireless LAN Connectivity • Feature Summary Kensington Lock A Kensington security slot is located on the router back panel. To secure the router to a desktop or other surface, use the Kensington lockdown equipment. Reset Button The Reset button resets the router configuration to the default configuration set by the factory.
Chapter 1 Product Overview Hardware Features Table 1-1 LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued) LED Color Description 860 Series 880 Series 890 Series FE WAN Port Link Status Green On—Port is connected.
Chapter 1 Product Overview Hardware Features Table 1-1 LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued) LED Color 7 xDSL CD Green Description 8 On—The xDSL interface is connected to the DSLAM . Blink—Training to the line. 860 Series 880 Series 890 Series 867 models— 886, 887, 887V, 888 models — 867 886 models 886, 887, 887V, 888 models — Off—Indicates that a connection has not been established or the port is shut down.
Chapter 1 Product Overview Hardware Features Table 1-1 LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued) LED Color Description 860 Series 880 Series 890 Series BRI Voice B1 Green On—BRI B1 channel is connected. — 888 SRST models — Blinking—BRI B1 channel is either receiving or transmitting data. BRI Voice B2 Green On—BRI B2 channel is connected.
Chapter 1 Product Overview Hardware Features The default flash memory for the Cisco 860 series and 880 series routers is 128 MB. The default flash memory for the Cisco 880 series voice routers and Cisco 890 series routers is 256 MB. Note Flash memory is not upgradable. An external USB flash memory module may be used if additional flash memory is needed. Main Memory The Cisco 860 series routers contain 256 MB of onboard memory. The onboard memory in the Cisco 860 series router is not expandable.
Chapter 1 Product Overview Hardware Features 3G Cellular Data WAN Connectivity The 3G (Evolution Data Only [EVDO], Universal Mobile Telecommunications Systems [UMTS]) cellular interface is intended for use as a backup data link, but it can also be used as a primary WAN data link. The 3G technology is third-generation wide-area cellular technology that is used in voice telephony and broadband wireless data in a mobile environment.
Chapter 1 Product Overview Hardware Features Supported Cisco Radio Antennas The Cisco 890 series ISRs come with three removable dipole antennas that can be replaced using the Cisco approved antenna extenders listed in Table 1-3. Table 1-3 Cisco Antennas Supported on the Cisco 890 Series ISRs Cisco Part Number Antenna Type Maximum Gain Description AIR-ANTM2050D-R Omnidirectional 2.0 dBi at 2.4 GHz This is the default antenna. It is a swivel-mount dipole dual-band blade antenna.
Chapter 1 Product Overview Hardware Features Table 1-4 Hardware Features Available in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued) Feature Description FE WAN port 860 Series 880 Series 890 Series Provides connection to 10/100BASE-T. Can be connected to 861 models other network devices, such as a cable modem, an xDSL6 modem, or router. The router is capable of bridging and multiprotocol routing between the LAN and WAN ports.
Chapter 1 Product Overview Hardware Features Table 1-4 Hardware Features Available in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued) Feature 16 FXS /DID port Description 17 BRI voice port 860 Series 880 Series 890 Series An FXS interface connects directly to a standard telephone, — fax machine, or similar device. This interface supplies ringing voltage and dial tone to the station.
CH A P T E R 2 Installing the Router This chapter describes the equipment and the procedures for successfully installing the Cisco 860 series, 880 series, and 890 series Integrated Services Routers (ISRs), and contains the following sections: • Equipment, Tools, and Connections, page 2-1 • Installing the Router, page 2-3 Note For compliance and safety information, see the Regulatory Compliance and Safety Information Roadmap that ships with the router and the Regulatory Compliance and Safety Informati
Chapter 2 Installing the Router Equipment, Tools, and Connections Items Shipped with your Router Unpack the box and verify that all items listed on the invoice were shipped with the router. Table 2-1 lists the items and their quantities that are shipped with each router model.
Chapter 2 Installing the Router Installing the Router Ethernet Devices Identify the Ethernet devices that you will connect to the router: hub, servers, and workstations or PCs. Ensure that each device has a network interface card (NIC) for connecting to Ethernet ports. • If you plan to configure the software using Cisco IOS commands through the console port, provide an ASCII terminal or a PC that is running terminal emulation software to connect to the console port.
Chapter 2 Installing the Router Installing the Router Caution Do not place anything on top of the router that weighs more than 10 pounds (4.5 kilograms), and do not stack routers on a desktop. Excessive weight on top of the router could damage the chassis. Caution Do not install the router or power supplies next to a heat source of any kind, including heating vents.
Chapter 2 Installing the Router Installing the Router Antennas Oriented Vertically Up 274774 Figure 2-2 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16193-03 2-5
Chapter 2 Installing the Router Installing the Router Antennas Oriented Vertically Down 274775 Figure 2-3 Installing on a Table To install the router on a table or other flat horizontal surface, firmly place the router on a table or other horizontal surface. Keep at least 1 inch (2.5 centimeters) of clear space beside the cooling inlet and exhaust vents. Connect the chassis to a reliable earth ground.
Chapter 2 Installing the Router Installing the Router Note The mounting holes are bidirectional. You can hang the router with the front bezel facing upwards or downwards. Tip When choosing a location for wall-mounting the router, consider cable limitations and wall structure. To mount the router on a wall, follow these steps: Step 1 Anchor the screws into the wall, leaving 1/8 inch (0.32 centimeter) between the screw head and the wall.
Chapter 2 Installing the Router Installing the Router Figure 2-5 Router Mounted on the Wall 1 1 4 231982 2 3 Step 3 1 Two number-10 wood screws mounted on the 3 wall 2 Wall-mount holes 4 Horizontal surface on which to place the power adapter Distance between the screw head and the wall, 1/8 in. (0.32 cm) Connect the chassis to a reliable earth ground. For the chassis ground connection procedures, see the “Installing the Router Ground Connection” section on page 2-10.
Chapter 2 Installing the Router Installing the Router Installing in a Rack The Cisco 890 series ISRs can be mounted in a rack. To install a Cisco 890 series ISR in a rack, follow these steps: Step 1 Remove the screws shown in Figure 2-6. Figure 2-6 Screw Location 278159 1 1 1 Step 2 Caution Screws Using the screws provided, attach the rack-mount brackets to the Cisco 890 series ISR chassis as shown in Figure 2-7. Use two screws on each side.
Chapter 2 Installing the Router Installing the Router Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety: -- This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
Chapter 2 Installing the Router Installing the Router Chassis Ground Connection Using Ring Terminal 231981 Figure 2-8 1 1 Step 4 Ring terminal Connect the other end of the ground wire to a known reliable earth ground point at your site. After you install and properly ground the router, you can connect the power wiring, the WAN and LAN cables, and the cables for administrative access as required for your installation.
Chapter 2 Installing the Router Installing the Router Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 2-12 OL-16193-03
CH A P T E R 3 Connecting the Router This chapter describes how to connect Cisco 860 series, Cisco 880 series, and Cisco 890 series Integrated Services Routers (ISRs) to Ethernet devices, Power over Ethernet (PoE), and the network. The chapter contains the following sections: • Preparing to Connect the Router, page 3-2 • Connecting a PC, Server, or Workstation, page 3-3 • Connecting a Phone, page 3-4 • Connecting an External Ethernet Switch, page 3-5 • Connecting the V.
Chapter 3 Connecting the Router Preparing to Connect the Router Note Depending on the features available for your router, some content in this chapter may not apply to your router. Preparing to Connect the Router Before you connect the router to the devices, install the router according to the instructions in Chapter 2, “Installing the Router.
Chapter 3 Connecting the Router Connecting a PC, Server, or Workstation Connecting a PC, Server, or Workstation To connect a PC (or other Ethernet devices) to an Ethernet switch port, follow these steps: Step 1 Connect one end of the yellow Ethernet cable to an Ethernet switch port on the router. Figure 3-1 shows a Cisco 888W router connected to a PC.
Chapter 3 Connecting the Router Connecting a Phone Connecting a Phone To connect an 802.3af-compliant phone to an Ethernet switch port, follow these steps: Connect one end of the yellow Ethernet cable to Ethernet switch port 0 or port 1 on the router. Figure 3-2 shows a Cisco 888W router connected to a phone.
Chapter 3 Connecting the Router Connecting an External Ethernet Switch Connecting an External Ethernet Switch If more than four PCs in an office must be connected to each other, you can add Ethernet connections to the router by connecting an external Ethernet switch to the router’s Ethernet switch. To connect an external Ethernet switch to an Ethernet switch port on the router, perform the following steps: Step 1 Connect one end of the yellow Ethernet cable to an Ethernet switch port on the router.
Chapter 3 Connecting the Router Connecting the V.92 modem Port Connecting the V.92 modem Port Warning Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end away from the unit first. Statement 1026 For dialup connection to your service provider network through the V.92 port, follow the steps given after Figure 3-4, which show this connection.
Chapter 3 Connecting the Router Connecting a Terminal or PC to the Console Port Connecting a Terminal or PC to the Console Port Connect a terminal or PC to the Console Aux port either to configure the software by using the command-line interface (CLI) or to troubleshoot problems with the router. To connect a terminal or PC to the console port on the router and access the CLI, follow these steps: Connect the RJ-45 end of a DB-9–to–RJ-45 serial cable to the RJ-45 Console Aux port on the router.
Chapter 3 Connecting the Router Connecting a Modem to the Auxiliary Port • 1 stop bit • No flow control When the terminal emulator establishes communications, the router prompt is displayed. For more information on terminal emulation settings, see Applying Correct Terminal Emulator Settings for Console Connections.
Chapter 3 Connecting the Router Connecting the 3G Card Step 4 Make sure that your modem and the router auxiliary port are configured for the same transmission speed (up to 115200 bits per second [b/s] is supported) and support mode control with data carrier detect (DCD) and data terminal ready (DTR). Connecting the 3G Card Note The Cisco 880G router does not support OIR of the 3G card. You must enter the shutdown command on the cellular interface before you remove the 3G card from the router.
Chapter 3 Connecting the Router Connecting the 3G Card Figure 3-7 Inserting the 3G Card 4 271473 3 2 3 1 6 5 5 1 3G card with the Cisco logo facing up 4 Screw holes for locking bracket 2 3G express card slot 5 Pin holes for aligning the locking bracket 3 Notches on the 3G card 6 SIMM slot (in HSPA1 cards only) 1. HSPA = High-Speed Packet Access. Open the top of the anti-theft locking bracket, as shown in Figure 3-8.
Chapter 3 Connecting the Router Connecting the 3G Card Step 3 Slide the opened locking bracket under the 3G card. The locking bracket should align with the notches on either side of the 3G card, as shown in Figure 3-9, and the pins on the locking bracket should be inserted into the corresponding holes in the router.
Chapter 3 Connecting the Router Connecting the 3G Card Step 4 Close the locking bracket, as shown in Figure 3-10. Figure 3-10 Closing the Locking Bracket 1 271580 2 1 Step 5 2 3G card Locking bracket Insert the screws, as shown in Figure 3-11, and tighten with a number 2 Phillips screwdriver.
Chapter 3 Connecting the Router Connecting a Data BRI Port Figure 3-12 Antenna connected to the 3G Card 272653 1 3 2 1 Antenna on a cradle 2 Antenna connector 3 Antenna connector receptacle1 1. In HSPA cards, the antenna connector receptacle is located on the right side of the 3G card. Step 7 Clean the flat surface to which you will affix the antenna. Step 8 Remove the protective tape from the adhesive on the bottom of the antenna cradle, then firmly press the cradle to the flat surface.
Chapter 3 Connecting the Router Connecting a Data BRI Port Although the following procedure shows a Cisco 888W data router, this procedure applies to all Cisco 880 series router with a Data BRI port. To connect the Data BRI port to the ISDN service provider, follow these steps: Step 1 Connect one end of the orange ISDN S/T cable to the Data BRI port on the router. Figure 3-13 shows a Data BRI connection.
Chapter 3 Connecting the Router Connecting an FE Line to an FE WAN Port Connecting an FE Line to an FE WAN Port To connect the Fast Ethernet (FE) WAN port on the router, follow these steps: Step 1 Connect one end of the yellow cable to the FE WAN port as shown in Figure 3-14. Figure 3-14 Connecting the FE WAN Port 1 231992 WAN FE 4 1 2 3 Internet Step 2 1 FE WAN port 2 CAT 5 cable 3 Modem connected to the Internet Connect the other end of cable to an available port on the modem.
Chapter 3 Connecting the Router Connecting an GE Line to an GE WAN Port Connecting an GE Line to an GE WAN Port To connect the Gigabit Ethernet (GE) WAN port on the router, follow these steps: Step 1 Connect one end of the yellow cable to the GE WAN port as shown in Figure 3-14. Connecting the GE WAN Port 274493 Figure 3-15 1 2 3 Internet Step 2 1 GE WAN port 2 CAT 5 cable 3 Modem connected to the Internet Connect the other end of cable to an available port on the modem.
Chapter 3 Connecting the Router Connecting an xDSL Line Connecting an xDSL Line Warning Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end away from the unit first. Statement 1026 To connect the router to a global industry standard symmetrical high-speed DSL (G.
Chapter 3 Connecting the Router Connecting Power over Ethernet Connecting Power over Ethernet Warning This unit might have more than one power supply connection. All connections must be removed to de-energize the unit. Statement 1028 Figure 3-17 shows how to connect the 48-VDC Power over Ethernet (PoE) power adapter to your router.
Chapter 3 Connecting the Router Connecting the AC Adapter Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120VAC, 20A U.S. (240VAC, 16 to 20A international) is used on the phase conductors (all current-carrying conductors). The fuse or circuit breaker must have adequate safety approvals recognized by the country of usage.
Chapter 3 Connecting the Router Connecting the AC Adapter Step 2 To secure the power cord to the router, attach the power lock clip to the power cord, and slide the clip to the end of the DC plug. See Figure 3-19.
Chapter 3 Connecting the Router Connecting an FXS Line Step 3 Snap the latches into the holes on either side of the power connector. See Figure 3-20. Figure 3-20 Power Lock Clip Latched Into the Holes on Either Side of the Power Connector 1 4 3 270800 2 1 Power lock clip 3 Power adapter 2 Power cord 4 AC plug Connecting an FXS Line Use a standard straight-through RJ-11 modular telephone cable to connect an Foreign Exchange Service (FXS) port to a telephone or fax machine.
Chapter 3 Connecting the Router Connecting an FXS Line To connect the FXS line, follow these steps: Step 1 Connect one end of the straight-through RJ-11 cable to the FXS port. Figure 3-21 shows an FXS line connection. Figure 3-21 Connecting an FXS Line 1 2 241907 3 Fax machine or telephone Step 2 1 FXS port 2 RJ-11 cable 3 RJ-11 port Connect the other end of the cable to the RJ-11 port on the fax or telephone machine.
Chapter 3 Connecting the Router Connecting an FXO Line Connecting an FXO Line Use a straight-through RJ-11 cable to connect the Foreign Exchange Office (FXO) voice port to the PSTN or PBX through a telephone wall outlet. Warning Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end away from the unit first.
Chapter 3 Connecting the Router Connecting a Voice ISDN BRI Line Note If you have specified the use of a private line automatic ringdown (PLAR) off-premises extension (OPX) connection mode for an FXO voice port (with loop resistance less than 8000 Ohm), you must ensure that the soft-offhook option is enabled on the port.
Chapter 3 Connecting the Router Connecting a Voice ISDN BRI Line Figure 3-23 shows a voice BRI line connection. Figure 3-23 Connecting a Voice BRI Line 1 2 241906 3 Step 2 1 Voice BRI port 2 RJ-45 cable 3 Telephone outlet Connect the other end of the cable to the RJ-45 telephone outlet or other device.
Chapter 3 Connecting the Router Verifying Connections Verifying Connections To verify that all devices are properly connected to the router, first turn on all the connected devices. Then check the LEDs. To verify router operation, refer to Table 3-1. For full LED description see Table 1-1 “LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs”.
Chapter 3 Connecting the Router Verifying Connections Table 3-1 Verifying the Router Operation (continued) Power and Link LEDs to Check Normal Patterns To wireless LAN WLAN LINK Wireless LAN link status: WLAN 2.4 GHz WLAN 5.0 GHz PoE14 • Green if at least one client is associated. • Off if no client is associated. Wireless LAN 2.4-GHz status: • Green when radio is connected, SSID13 is configured, signal is being transmitted, and client is associated.
Chapter 3 Connecting the Router Verifying Connections Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-28 OL-16193-03
CH A P T E R 4 Initial Configuration This chapter provides instructions for initial configuration of the Cisco 860 series, 880 series, and 890 series Integrated Services Routers (ISRs). For the initial configuration, we recommend using Cisco Configuration Professional (CP) Express. Cisco CP Express is a web-based graphical user interface that guides you through initial configuration.
Chapter 4 Initial Configuration Cisco IOS CLI To configure the initial router settings using the Cisco IOS CLI, follow these steps: Step 1 Set up a console connection to your router. The following message is displayed: ... router con0 is now available Step 2 Press Return or Enter. The following message is displayed: Cisco Configuration Professional Express (Cisco CP Express) is installed on this device. This feature requires the one-time use of the username "username1" with the password "password1.
Chapter 4 Initial Configuration Setup Command Facility Step 6 Verify the initial configuration. See the “Verifying the Initial Configuration” section on page 4-5. Setup Command Facility The setup command facility guides you through the configuration process by prompting you for the specific information that is needed to configure your system.
Chapter 4 Initial Configuration Setup Command Facility Basic management setup configures only enough connectivity for management of the system, extended setup will ask you to configure each interface on the system Would you like to enter basic management setup? [yes/no]: yes Step 5 Enter a hostname for the router (this example uses Router): Configuring global parameters: Enter host name [Router]: Router Step 6 Enter an enable secret password.
Chapter 4 Initial Configuration Verifying the Initial Configuration ! no ip routing ! interface FastEthernet0 no shutdown speed 100 duplex auto ip address 172.1.2.3 255.255.0.0 ! Step 12 Respond to the following prompts. Enter 2 to save the initial configuration. [0] Go to the IOS command prompt without saving this config. [1] Return back to the setup without saving this config. [2] Save this configuration to nvram and exit. Enter your selection [2]: 2 Building configuration...
Chapter 4 Initial Configuration Initial Configuration of the Wireless Access Point For information on how to do basic wireless configuration on your router see the “Basic Wireless Device” chapter of the Cisco 860 Series, Cisco 880, and Cisco 890 Series Integrated Services Routers Software Configuration Guide.
A P P E N D I X A Technical Specifications This appendix provides router, port, and cabling specifications for the Cisco 860 series, Cisco 880 series, and Cisco 890 series Integrated Services Routers (ISRs).
Appendix A Technical Specifications Router Specifications Router Specifications Table A-1 lists the system specifications for the routers. Table A-1 Router Specifications Description Design Specification Physical Dimensions Dimensions with antenna and rubber feet (H x W x D) 1.9 x 12.8 x 10.4 in. Weight (not including desktop power supply) 5.5 lb (2.
Appendix A Technical Specifications Wireless Access Point Wireless Access Point Table A-2 lists the specifications for the wireless access point (AP). Table A-2 Wireless Access Point Specifications Description Design Specification Radio technology IEEE 802.11n draft 2.0 standard compliant. 2x3 MIMO1 radio. Backward compatible with 802.11b/g and 802.11a (Cisco 890 series routers). Operating frequency Cisco 860 series and 880 series ISRs 2.4-GHz radio band Cisco 890 series ISRs 2.
Appendix A Technical Specifications Console and Auxiliary Port Connector Pinouts Console and Auxiliary Port Connector Pinouts Table A-4 lists the pinouts for the console and auxiliary port connectors. Table A-4 Console and Auxiliary Port Connector Pinouts RJ-45 Pin Function 1 RTS 2 DTR 3 TXD 4 GND 5 GND 6 RXD 7 DSR 8 CTS FXS and FXO Port Connector Pinouts Table A-6 lists the FXS and FXO connector pinouts.
Appendix A Technical Specifications ADSL2+ Port Connector Pinouts Table A-6 VDSL2 Connector Pinouts (RJ-11-to-RJ-45) (continued) RJ-11 Pin Function 5 Unused 6 Unused ADSL2+ Port Connector Pinouts Table A-6 lists the ADSL2+ connector pinouts. Table A-7 ADSL2+ Connector Pinouts (RJ-11) RJ-11 Pin Function 1 Unused 2 Unused 3 TIP 4 RING 5 Unused 6 Unused V.92 Port Connector Pinouts Table A-8 lists the V.92 connector pinouts. Table A-8 V.
Appendix A Technical Specifications G.SHDSL Port Connector Pinouts G.SHDSL Port Connector Pinouts Table A-9 lists the pinouts for the global industry standard symmetrical high-speed DSL (G.SHDSL) WAN port. Table A-9 G.SHDSL WAN Port Pinouts Pin Function 1 Unused 2 TIP (Port1) 3 TIP (Port0) 4 TIP (Port0) 5 TIP (Port1) 6 Unused Data BRI Port Connector Pinouts Table A-10 lists the pinouts for the Data BRI port.
Appendix A Technical Specifications Cable Specifications 1. Use a straight-through cable for NT interfaces. 2. Use a crossover cable for TE interfaces. Cable Specifications This section provides specifications for the following Ethernet cables: • Straight-through cable • Crossover cable Because of the autocrossover (autosensing) function, both straight-through and crossover cables can be used for the Ethernet LAN port.
Appendix A Technical Specifications Cable Specifications Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide A-8 OL-16193-03
