User Manual

© 2016 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information. Page 8 of 14
Feature
Description
VLAN mirroring
Traffic from a VLAN can be mirrored to a port for analysis with a network analyzer or RMON probe. Up to 4 source
VLANs can be mirrored to one destination port. A single session is supported.
Dynamic Host
Configuration Protocol
(DHCP) (options 66
and 67)
(DHCP) options facilitate tighter control from a central point (DHCP server) to obtain IP address and perform auto-
configuration (with configuration file download)
Text-editable config
files
Config files can be edited with a text editor and downloaded to another switch, facilitating easier mass deployment
Smartports
Simplified configuration of QoS and security capabilities
Not supported on SG200-08 and SG200-08P
Auto Smartports
Automatically applies the intelligence delivered through the Smartports roles to the port based on the devices
discovered over Cisco Discovery Protocol or LLDP-MED. This facilitates zero touch deployments.
Not supported on SG200-08 and SG200-08P
Cloud services
Support for FindIT Network Discovery Utility and Cisco Active Advisor
Localization
Localization of GUI and documentation into multiple languages
Other management
HTTP, RADIUS, port mirroring, TFTP upgrade, DHCP client, BOOTP, SNTP, ping, syslog
Power Efficiency
EEE compliant
(802.3az)
Supports 802.3az on all copper Gigabit Ethernet ports (SG200-xx models)
Not supported on SG200-08 and SG200-08P
Energy Detect mode
Automatically turns off power on Gigabit Ethernet RJ-45 port when the switch detects a link down
Active mode is resumed without loss of any packets when the switch detects that the link is back up
Cable length detection
Adjusts the signal strength based on the cable length. Reduces the power consumption for cables shorter than 10 m.
Not supported on SG200-08 and SG200-08P
General
Jumbo frames
Frame sizes up to 10 KB supported on 10/100 and Gigabit Ethernet interfaces
(9 KB for SG200-08 and SG200-08P)
MAC table
Up to 8,000 MAC addresses
Discovery
Link Layer Discovery
Protocol (LLDP)
(802.1ab) with
LLDP-MED extensions
LLDP allows the switch to advertise its identification, configuration, and capabilities to neighboring devices, which
store the data in an MIB. LLDP-MED is an enhancement to LLDP that adds the extensions needed for IP phones.
Cisco Discovery
Protocol
The switch advertises itself using the Cisco Discovery Protocol. It also learns the connected device and its
characteristics via this protocol.
Not supported on SG200-08 and SG200-08P
Auto Smartports
Automatically applies the intelligence delivered through the Smartports roles to the port based on the devices
discovered over Cisco Discovery Protocol or LLDP-MED. This capability facilitates zero-touch deployments.
Not supported on SG200-08 and SG200-08P
Bonjour
The switch advertises itself using the Bonjour protocol
Power over Ethernet (PoE)
IEEE 802.3af PoE
delivered on half of the
RJ-45 ports within the
listed power budgets
Maximum power of 15.4W to any 10/100 or Gigabit Ethernet base port supporting PoE. The total power available for
PoE per switch is as follows:
Model
Power Dedicated to PoE
Number of Ports That Support PoE
SF200-24P
100W
12
SF200-24FP
180W
24
SF200-48P
180W
24
SG200-08P
32W
4
SG200-10FP
62W
8
SG200-26P
100W
12
SG200-26FP
180W
24
SG200-50P
180W
24