User guide

ManualsBrandsCisco ManualsConsumer electronicsSPA302D

Quick Start Guide

Cisco SPA302D Mobility Enhanced Cordless

Handset

Package Contents

• Cisco SPA302D Mobility Enhanced Cordless Handset

• Charging Cradle

• Belt Clip

• Power Adapter

• Power Clip

• Two rechargeable AAA batteries

• Product CD-ROM

• Quick Start Guide

Welcome

Thank you for choosing the Cisco SPA302D. This guide describes how to

physically set up and register your Cisco SPA302D to the Cisco SPA232D ATA.

It also describes how to perform some basic tasks, such as placing and

answering calls, and configuring basic phone options.

Before You Begin

Before you begin the installation, make sure that you have the following

equipment and services:

• Cisco SPA232D Mobility Enhanced ATA, which has an integrated DECT

Base Station to provide telephone service for the SPA302D

• Active Internet connection

• Active Public Switched Telephone Network (PSTN) connection or Voice

over IP (VoIP) phone service account

• PC with web browser, for using web-based system management tools

(Microsoft Internet Explorer, Mozilla Firefox, and Apple Safari are supported)

Battery Warning

Use only size AAA Ni-MH 800 mAh (1.2V) rechargeable batteries in the

Cisco SPA302D handset. Place the handset in the charging cradle for a

recommended initial charge of 10 hours before using the handset for the first

time.

Cisco SPA302D Features

Table 1 Handset Features

1Receiver.

2 Handset display.

3 Right softkey. Press the softkey to perform the action shown in the

lower right of the handset display.

4 End Call button. Press the button and hold it to turn off the handset.

5Keypad.

6 Mute button.

7 Microphone.

8 Speakerphone button. Press this button during a call to use the

speakerphone.

9Start Call button.

10 Left softkey. Press the softkey to perform the action shown in the lower

left of the handset display.

11 4-way navigation keypad. Press the arrow buttons to move up, down,

left, or right through menus displayed on the handset.

12 Center Select button.

13 Headset port.

14 Speaker.

Handset Setup and Registration

Charging the Handset

STEP 1 Remove the back cover of the handset.

STEP 2 Insert the two AAA rechargeable batteries (included) into the handset.

(See Battery Warning in “Before You Begin.”)

Correct battery placement is shown on the label inside the battery

compartment. If the batteries are charged, the handset turns on when

the batteries are inserted. If the batteries are not charged, the handset

turns on when it is placed into the charging cradle.

STEP 3 Remove the protective film from the handset and charging cradle.

STEP 4 Insert the power clip into the power adapter.

STEP 5 Plug the power adapter into the power source.

STEP 6 Connect the power adapter into the charging cradle in the port shown

below.

CAUTION Only use the power adapter designed for use with Cisco SPA300

Series devices.

STEP 7 Place the handset into the charging cradle. The light on the charging

cradle appears solid green when the handset is charging. Charge the

handset for a minimum of 10 hours before using the handset for the

first time to ensure that the handset is fully charged.

Registering the Handset to the Cisco SPA232D Mobility

Enhanced ATA

STEP 1 Install and configure the Cisco SPA232D. See the Cisco SPA232D

Quick Start Guide for more information.

STEP 2 On the Cisco SPA302 handset, press the Select button in the center of

the 4-way navigation keypad.

STEP 5 Select Register.

STEP 6 On the Cisco SPA232D, press the Page/Registration button and hold

it down for at least seven seconds until the green status light flashes

quickly.

TIP: If you press the button for fewer than seven seconds, the green

status light flashes slowly, indicating the unit is in “paging” mode and is

not in registration mode. Registration will not work if the unit is in

paging mode.

STEP 7 The default PIN is blank, so do not enter a PIN. Press the left softkey to

confirm that you want to register the handset. The “registering”

message appears.

STEP 3

TEP 4

Using the navigation arrows, scroll to the Settings icon and

press the center navigation button to select it.

Select Handset Registration.

STEP 8 To verify that the handset registered to the base station,

confirm that the signal strength icon is solid (not flashing)

and that the handset ID, such as Handset 1 or Handset 2,

appears near the top right corner of the display screen.

Version en français sur CD

Summary of content (2 pages)

PAGE 1
Welcome Quick Start Guide 2 Thank you for choosing the Cisco SPA302D. This guide describes how to physically set up and register your Cisco SPA302D to the Cisco SPA232D ATA. It also describes how to perform some basic tasks, such as placing and answering calls, and configuring basic phone options. 1 Cisco SPA302D Features Charging the Handset STEP 1 Remove the back cover of the handset. Correct battery placement is shown on the label inside the battery compartment.
PAGE 2
4 Using Your Cisco SPA302D Putting a Call on Hold To put a call on hold, press the left softkey to select Options. Scroll to Hold and press the center Select button. The hold icon and onscreen message indicates a call is on hold. Placing a Call To place a call, do one of the following tasks: • Enter the number on the keypad and press the green Start Call button. Depending on your phone system configuration, you may have to enter a digit, such as 9, before entering the number to place an external call.