® A Division of Cisco Systems, Inc. 12 Volt Power Over Ethernet Adapter Kit WIRED Model No.
12 Volt Power Over Ethernet Adapter Kit Copyright and Trademarks Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2004 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders.
12 Volt Power Over Ethernet Adapter Kit Table of Contents Chapter 1: Introduction 1 Welcome What’s in this Guide? 1 3 Chapter 2: Getting to Know the 12 Volt Power Over Ethernet Adapter Kit Overview The Injector The Splitter Chapter 3: Connecting the 12 Volt Power Over Ethernet Adapter Kit Overview Powering on a Device that Uses a Standard Power Adapter Powering on a Device that Uses Inline Power Appendix A: Glossary Appendix B: Specifications Appendix C: Warranty Information Appendix D: Regulatory In
12 Volt Power Over Ethernet Adapter Kit List of Figures Figure 2-1: Injector’s First Side Panel Figure 2-2: Injector’s Second Side Panel Figure 2-3: Injector’s LED Figure 2-4: Splitter’s First Side Panel Figure 2-5: Splitter’s Second Side Panel Figure 2-6: Splitter’s LED Figure 3-1: Power Over Ethernet Kit Used with a Switch and Access Point Figure 3-2: Connect the Ethernet Cable to the Injector Figure 3-3: Connect the Ethernet Cable to the Splitter Figure 3-4: Barrel Jack Adapter (optional) Figure 3-5: Co
12 Volt Power Over Ethernet Adapter Kit Chapter 1: Introduction Welcome Thank you for choosing the Linksys 12 Volt Power Over Ethernet Adapter Kit. It will let you put your wireless access point or other network device almost anywhere, by eliminating the need for a nearby electrical outlet. The best place for an access point is usually on the ceiling, in the center of the area that needs wireless coverage, and the second best place would be high up on a wall.
12 Volt Power Over Ethernet Adapter Kit • BEFCMU10 (all versions) - Cable Modem with USB and Ethernet Connections • BEFCMUH4 - Cable Gateway • BEFDSR41W - ADSL Gateway • BEFSX41 (versions 1 and 2) - Broadband Firewall Router with 4-Port Switch/VPN Endpoint • BEFW11S4 (version 4) - Wireless-B Broadband Router • RT31P2 - Broadband Router with 2 Phone Ports • WAG54G (versions 1.
12 Volt Power Over Ethernet Adapter Kit What’s in this Guide? This guide covers the steps for installing the Power Over Ethernet Adapter Kit. • Chapter 1: Introduction This chapter describes the Power Over Ethernet Adapter Kit’s application and this User Guide. • Chapter 2: Getting to Know the 12 Volt Power Over Ethernet Adapter Kit This chapter describes the physical features of the Power Over Ethernet Adapter Kit.
12 Volt Power Over Ethernet Adapter Kit 4 Chapter 1: Introduction What’s in this Guide?
12 Volt Power Over Ethernet Adapter Kit Chapter 2: Getting to Know the 12 Volt Power Over Ethernet Adapter Kit Overview The Power Over Ethernet Adapter Kit is comprised of two devices, the Injector and Splitter. Use the Kit so you can move your access point, wireless bridge, or other network device to a remote location that is far from an electrical outlet. The Injector The Injector’s built-in cable and ports are located on side panels.
12 Volt Power Over Ethernet Adapter Kit The Injector’s Second Side Panel The built-in Ethernet network cable and Power port are located on the Injector’s second side panel. Ethernet IN The Injector has a built-in Ethernet network cable. You will connect this cable to one of the Ethernet network ports on your router or switch. Power The Power port is where you will connect the included adapter. The Injector’s LED The Power LED is located on the top of the Injector.
12 Volt Power Over Ethernet Adapter Kit The Splitter The Splitter’s built-in cables and port are located on side panels. The Splitter’s First Side Panel The Power & Data IN port is located on the Injector’s first side panel. Power & Data IN This port allows you to connect the Splitter to the Injector. (You will use the included Ethernet network cable to make this connection.
Volt Power Over Ethernet Adapter Kit The Splitter’s LED The Splitter’s LED is located on the top of the Splitter. Figure 2-6: Splitter’s LED Power LED 8 Green. The Power LED lights up when the Splitter is powered on and ready for use.
12 Volt Power Over Ethernet Adapter Kit Chapter 3: Connecting the 12 Volt Power Over Ethernet Adapter Kit Overview This chapter gives instructions on how to connect the Power Over Ethernet Kit. Once connected, the Kit will transmit data and power over the Ethernet network cable to your remotely located network device. The diagram shows an example of how the Kit can be connected to a wired switch and a wireless access point.
12 Volt Power Over Ethernet Adapter Kit Powering on a Device that Uses a Standard Power Adapter To use the Power Over Ethernet Kit, follow these instructions: 1. Connect the Injector’s built-in Ethernet network cable to your router, switch, or other network device. 2. Connect the Kit’s included Ethernet network cable to the Injector’s Power & Data OUT port. Then connect the other end to the Splitter’s Power & Data IN port.
12 Volt Power Over Ethernet Adapter Kit 3. Connect the Splitter’s built-in Ethernet network cable to the Ethernet port of your remotely located access point or other network device. 4. Connect the Splitter’s Power cord to the Power port of your remotely located access point or other network device. NOTE: If the plug of the Splitter’s Power cord does not fit into your network device, then use the included barrel jack adapter.
12 Volt Power Over Ethernet Adapter Kit Powering on a Device that Uses Inline Power You will use only the Injector to power up a device that supports inline power. Follow these instructions: 1. Connect the Injector’s built-in Ethernet network cable to your router, switch, or other network device. 2. Connect the Kit’s included Ethernet network cable to the Injector’s Power & Data OUT port. Then connect the other end to the Ethernet port of your remotely located access point or other network device.
12 Volt Power Over Ethernet Adapter Kit Appendix A: Glossary 802.11a - A wireless networking standard that specifies a maximum data transfer rate of 54Mbps and an operating frequency of 5GHz. 802.11b - A wireless networking standard that specifies a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz. 802.11g - A wireless networking standard that specifies a maximum data transfer rate of 54Mbps, an operating frequency of 2.4GHz, and backward compatibility with 802.11b devices.
12 Volt Power Over Ethernet Adapter Kit Boot - To start a device and cause it to start executing instructions. Bridge - A device that connects different networks. Broadband - An always-on, fast Internet connection. Browser - An application program that provides a way to look at and interact with all the information on the World Wide Web. Buffer - A shared or assigned memory area that is used to support and coordinate different computing and networking activities so one isn't held up by the other.
12 Volt Power Over Ethernet Adapter Kit DHCP (Dynamic Host Configuration Protocol) - A networking protocol that allows administrators to assign temporary IP addresses to network computers by “leasing” an IP address to a user for a limited amount of time, instead of assigning permanent IP addresses. DMZ (Demilitarized Zone) - Removes the Router's firewall protection from one PC, allowing it to be “seen” from the Internet.
12 Volt Power Over Ethernet Adapter Kit Firewall - A set of related programs located at a network gateway server that protects the resources of a network from users from other networks. Firmware - The programming code that runs a networking device. Fragmentation -Breaking a packet into smaller units when transmitting over a network medium that cannot support the original size of the packet. FTP (File Transfer Protocol) - A protocol used to transfer files over a TCP/IP network.
12 Volt Power Over Ethernet Adapter Kit IPSec (Internet Protocol Security) - A VPN protocol used to implement secure exchange of packets at the IP layer. ISM band - Radio bandwidth utilized in wireless transmissions. ISP (Internet Service Provider) - A company that provides access to the Internet. LAN - The computers and networking products that make up your local network. MAC (Media Access Control) Address - The unique address that a manufacturer assigns to each networking device.
12 Volt Power Over Ethernet Adapter Kit OFDM (Orthogonal Frequency Division Multiplexing) - Frequency transmission that separates the data stream into a number of lower-speed data streams, which are then transmitted in parallel to prevent information from being lost in transit. Packet - A unit of data sent over a network. Passphrase - Used much like a password, a passphrase simplifies the WEP encryption process by automatically generating the WEP encryption keys for Linksys products.
12 Volt Power Over Ethernet Adapter Kit SMTP (Simple Mail Transfer Protocol) - The standard e-mail protocol on the Internet. SNMP (Simple Network Management Protocol) - A widely used network monitoring and control protocol. Software - Instructions for the computer. A series of instructions that performs a particular task is called a “program”. SOHO (Small Office/Home Office) - Market segment of professionals who work at home or in small offices.
12 Volt Power Over Ethernet Adapter Kit TFTP (Trivial File Transfer Protocol) - A version of the TCP/IP FTP protocol that has no directory or password capability. Throughput - The amount of data moved successfully from one node to another in a given time period. Topology - The physical layout of a network. TX Rate - Transmission Rate. UDP (User Datagram Protocol) - A network protocol for transmitting data that does not require acknowledgement from the recipient of the data that is sent.
12 Volt Power Over Ethernet Adapter Kit Appendix B: Specifications Model WAPPOE12 Standards IEEE 802.3, 802.3u, 802.3af Ports Injector: Power, Data and Power OUT Splitter: Data and Power IN Cabling Type Category 5 or better LED Power Dimensions (W x H x D) 3.15" x 0.87" x 2.20" (80 mm x 22 mm x 56 mm) Unit Weight 2.65 oz. (0.075 kg) Power External Adapter: 100~240VAC, Injector 48VDC Certifications FCC Class B Operating Temp. 32°F to 104°F (0°C to 40°C) Storage Temp.
12 Volt Power Over Ethernet Adapter Kit Operating Humidity 10% to 85%, Non-Condensing Storage Humidity 5% to 90%, Non-Condensing 22 Appendix B: Specifications
12 Volt Power Over Ethernet Adapter Kit Appendix C: Warranty Information LIMITED WARRANTY Linksys warrants to You that, for a period of one year (the “Warranty Period”), your Linksys Product will be substantially free of defects in materials and workmanship under normal use. Your exclusive remedy and Linksys' entire liability under this warranty will be for Linksys at its option to repair or replace the Product or refund Your purchase price less any rebates.
12 Volt Power Over Ethernet Adapter Kit IN NO EVENT WILL LINKSYS’ LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply even if any warranty or remedy provided under this Agreement fails of its essential purpose. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to You. Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623.
12 Volt Power Over Ethernet Adapter Kit Appendix D: Regulatory Information FCC STATEMENT This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
12 Volt Power Over Ethernet Adapter Kit EC DECLARATION OF CONFORMITY (EUROPE) In compliance with the EMC Directive 89/336/EEC, Low Voltage Directive 73/23/EEC, and Amendment Directive 93/68/EEC, this product meets the requirements of the following standards: • EN55022 Emission • EN55024 Immunity SAFETY NOTICES Caution: To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord. Do not use this product near water, for example, in a wet basement or near a swimming pool.
12 Volt Power Over Ethernet Adapter Kit Appendix E: Contact Information Need to contact Linksys? Visit us online for information on the latest products and updates to your existing products at: http://www.linksys.com or ftp.linksys.
12 Volt Power Over Ethernet Adapter Kit 28 Appendix E: Contact Information
www.linksys.
