IPSO - LSG n.v. Instruction manual HF150 HF185 HF234 Technical specifications Installation instructions Operating instructions Maintenance Nieuwstraat 146 - B-8560 Wevelgem (België) Tel. 056/41 20 54 - Fax 056/41 86 74 Part No.
Contents 1 General safety instructions .......................................................................... 3 2 Technical data and dimensions ................................................................... 4 Technical data .................................................................................................. 4 Dimensions ....................................................................................................... 6 3 Installation and connection .......................
1 General safety instructions Ignoring any of the safety instructions can cause serious personal injury and can also cause damage to the linen or the machine ❐ ❐ ❐ ❐ Read the installation and instruction manual carefully before connecting the machine. It is recommended that the machine be installed by qualified technicians. The machine should be installed according to the installation instructions.
2 Technical data and dimensions Technical data HF150 HF185 1/11 13 kg 16,4 kg 1/10 14,5 kg 18 kg 1/9 16 kg 20 kg Capacity (dry weight) Cylinder Diameter 680 mm 680 mm Depth 400 mm 500 mm Volume 145 Lit 181 Lit Height 1348 mm 1348 mm Width 780 mm 780 mm Depth 840 mm 940 mm Diameter door opening 395 mm 395 mm Door height 565 mm 565 mm To center 770 mm 770 mm Cabinet Front loading Speed Wash 10 - 50 tr/min Distribution 85 tr/min Low spin 250 - 500 tr/min High spin
2 Technical data and dimensions Technical data HF234 Capacity (dry weight) 1/11 21,3 kg 1/10 23,4 kg 1/9 26 kg Cylinder Diameter 750 mm Depth 530 mm Volume 234 Lit Height 1505 mm Width 900 mm Depth 985 mm Diameter door opening 395 mm Cabinet Front loading Door height 630 mm To center 820 mm Speed Wash Distribution 10 - 50 tr/min 100 tr/min Low spin 250 - 500 tr/min High spin 500 - 1000 tr/min G-factor Low spin/high spin 74/ 373 4p. 1470 tr.
2 Dimensions HF150 - 185 220 565 1348 1375.5 88 50 680 50 34 HF150 = 665 - HF185 = 765 780 HF150 = 733 - HF185 = 833 86.5 HF150 = 753 - HF185 = 853 332 267 202 200 155 105 A F G D B C E H I 35 1181.5 703.5 K 185 935 1066.5 1141.5 L 170 J J J J J J J J J J J A. Ventilation soap dispenser B. Liquid soap connetions C. Hard water connections 3/4" D. Warm water connections 3/4" E. Soft water connections 3/4" F. Connections clamps G.Electrical connections H.Emergency button I.
2 Dimensions HF234 60 240 645 1527.5 1500 H 738 81 35 81 HF234 = 830 35 HF234 = 926 900 HF234 = 939.5 70 346 251 173 155.5 94 A C E D F G B I 1309.5 L 720 1265.5 K 165 1386 35 105 J J J J J J J J J J J A. Ventilation soap dispenser B. Liquid soap connetions C. Hard water connections 3/4" D. Warm water connections 3/4" E. Soft water connections 3/4" F. Connections clamps G.Electrical connections H.Emergency button I. Ventilation tub K. Drain valve L.
3 Installation and connection Ground The machine must be placed on a flat, solid surface (metal base, concrete or solid ground). It is recommended that the machine be anchored on the provided places (A) in the base, especially in case of a plinth (see Dimensions 2). The machine must be placed entirely level. For easy maintenance it is recommended to keep a minimal distance of 600 mm between the wall and the back of the machine.
3 Water drain The machine is equipped with a drain valve (HF150-185) with 2" outer diameter (50mm) (HF234) 3" outer diameter (80 mm). This drain valve should be connected to the drain by means of the drain elbow which is delivered with the machine. J The diameter of the main drain should be adapted to the water flow and the number of machines. It should be sufficient to handle at least 160L/min. per machine.
3 Liquid soap connection (option) Connection of the liquid soap hoses Electrical connection of the liquid soap pumps The liquid soap connection consists of 8 connections for liquid soap (SI….S). The central opening is used for ventilation. On machines equipped with a liquid soap connection, connect the wires directly on the print board next to the ground wire connection (option). Connect as indicated on the wiring diagram. The two connectors on the right give a tension of 220V ~ (max.
3 Connection of a central operating panel for coinmachines (option) At the backside above the main connectors, you find a printboard, to which the central operating panel for coinmachines can be connected. The right connectors form a potential free output contact as a result of which the operating panel detects when the machine is activated or not. The left connectors receive the signal, by means of which a machine is chosen through the operating panel.
3 Steam connection Machines with steam heating must have a steam valve between the steam installation and the machine. With direct steam injection into the machine 1. 2. 3. 4. 5. 6. 7. Steam pipe Steam cut-off valve 3/8" Pipe coupling 3/8" Steam filter 3/8" Magnetic steam valve 3/8" Curve MF 3/8" Steam hose with appropriate pipe coupling 3/8" Added parts for steam heating with heat exchanger 3. 9. 10. 11. 12.
4 Operating instructions Machine with start button Opening the door Fill the drum Open the door. Sort the linen according to the type and required temperature of the linen. Empty all pockets of the garments so that no garments can be damaged and no left articles can cause damage to the machine. Turn sleeves of shirts, blouses inside out. It is recommended to mix small and large items to enhance the drop of the linen during the wash cycle and hence improve the wash quality.
4 Start the machine Start the wash-cycle by pressing the Start button (S) and releasing it immediately. The door is sealed and the cycle-LED lights up. During the first 2 minutes after starting, the program number is blinking and you can change the program in case of a possibly wrong selection. To do so, select another program with the SELECT button (P). This new program will start immediately.
4 During final spin, both the left spin-LED (intermediate spin) will light up together with the right spin-LED (final spin). - Functioning of the spin-LED’s during final spin: LED drain/distribution low spin high spin coast tumble Interm. spin blinking rapidly continuously slowly continuously off continuously continuously slowly continuously rapidly coast tumble Final spin - Functioning of the spin-LED’s during gentle-final spin: LED Interm.
Description of the functions 4 Function F1 (Time stop) During the wash cycle: The wash time is stopped. The temperature, water level and wash action remain the same as programmed. During the wash cycle, this function remains active until the START button (S) is pressed again. During intermediate spin : The intermediate spin normally lasts 1 minute. By activating function F1, the machine will spin for nine minutes unless the START button (S) is pressed earlier.
4 Function F3 (reduced wash action): By selecting F3, the wash action time and pause time will be reversed; unless the wash action time was programmed to be shorter than the pause time. Example: 12 sec. action/3 sec. pause becomes: 3 sec. action/12 sec. pause 6 sec. action/9 sec. pause remains: 6 sec. action/9 sec. pause This function does not influence the cycle time - the program continues normally - and remains active until the START-button (S) is pressed.
4 End of a program At the end of a program, while the door is being released, the left display shows End; and the Start-LED is switched off. After that only the right display will continue to show the program number. This is the end of the program. Premature ending of the program By pressing the START-button (S) during the program, the Start-LED is switched off and the water is drained from the machine.
4 Remarks: Freely programmable stop-function Before starting a program it is possible to preprogram a time stop in every program segment. This function permits special additional functions like adding bleach or extra detergent to the wash bath. Programming: After selecting the program, press the ECO-button (E) and keep it depressed. Now push the START-button (S) simultaneously and release same. Only now release the ECO-button (E).
4 Linking 2 programs It is possible to run 2 programs automatically in sequence. This can be handy to perform very special functions (like waterproofing outerwear) and add these to the wash program. Programming: First select the program which will be run last. Now, press the START-button (S) and keep it depressed for at least 5 seconds.The left display now shows “Add”. Now select the program which will be run first.
4 Machine with coin or token operation Opening the door Fill the drum Open the door. Sort the linen according to the type and required temperature of the linen. Empty all pockets of the garments so that no garments can be damaged and no left articles can cause damage to the machine. Turn sleeves of shirts, blouses inside out. It is recommended to mix small and large items to enhance the drop of the linen during the wash cycle and hence improve the wash quality.
4 Indications of program sequence Display information The left display will indicate the temperature of the wash bath - in °C or °F (on machines where this function has been selected). The central display shows the remaining time to the end of the wash cycle. For programs which are being run for the first time, the machine will take a theoretical time estimate.
4 End of a program Remarks At the end of a program, while the door is being released, the left display shows End and the Start-LED is switched off. After that only the right display will continue to show the program number. This is the end of the program. Rapid advance This function allows to skip the rest or certain segments of the program. This function has to be specified during preprogramming and is mostly used by technicians and maintenance personnel.
4 Cool down This function allows to gradually lower the temperature of the wash bath to prevent creasing of the linen. During a cool down, the remaining program time on the central display will be replaced by “cd”. Power Failure Should the power fall out during the program, the water will be drained and the door can be opened after maximum 3 minutes. When the door remains locked, and the power comes back up within 24 hours, the program will continue from there, where it was at the time of the power failure.
4 Setting the price The price is set according to the specifications at the time of ordering the machine. If no prices were specified, some standard amounts have been preset. Every program can be priced differently. These prices can also be modified easily. Accessing the price setting mode Remove the coin box from its house. Certain machines have a press button inside the coin box house at the left upper part. Access to the price setting mode is obtained using this button.
5 After programming the price for the last program, there are still the following parameters : A : Eco - price This is the decrease in value of the price for economical wash. In other words, the amount that the customer is saving by using economic wash. B : Number of coin insertions COIN 1 (up to 60.000) This parameter is only indicated if it has been programmed as such in the programmation (COIN COUNT). C : Number of coin insertions COIN 2 (up to 60.
5 Standard programs The machine is standard equipped with 10 programs (0+9). These have been designed in cooperation with specialized detergent manufacturers to obtain the best possible wash results using the most frequently used detergents. Program 0 (starching) is mostly used in very special applications and is therefore not displayed on the front panel. 0. Starching 1 RINSE COLD 1. HOT WASH 2 BATHS 40°/90°C 2. HOT WASH 1 BATH 90°C 3. COLOUREDS 2 BATHS 40°/60° 4. COLOUREDS 1 BATH 60°C 5.
6 Technical remarks Internal connections of the electrical heating ▲ Heating 3x220V R5 3x380V R5 9kw 3x3kw ▲ LC1D1810 ★ LC1D0901 12kw 3x2kw 3x2kw ▲ LC1D253 ★ LC1D0901 15kw 3x2kw 3x3kw ▲ LC1D253 ★ LC1D1810 18kw 3x3kw 3x3kw ▲ LC1D323 ★ LC1D1810 21kw 3x3kw 3x4kw ----------- ----------- ★ ▲ LC1D1810 LC1D1810 24kw 3x4kw 3x4kw ----------- ----------- ▲ ▲ LC1D1810 LC1D1810 ★ B = Black Gy = Grey R = Red PU = Purple Br = Brown Bu = Blue W = White W/B = White/black Remark
6 Error messages When one of the following malfunctions occurs during a program, the central display will communicate the appropriate error message at the end of the cycle. E3 (Eprom) The Eprom is wrong, replace it by another. Nota: For coin op machines, it is possible that a program number appears on the right display in combination with E3. This indicates a wrong price adjustment for this program. A coin value “0” or bigger than “1000” was programmed. Example : wrong price adjustment for program 5.
6 E9 (motor protection) The thermo-magnetic protection was activated 5 times. EA (tilt) The tilt switch was activated 15 times during final spin and the final spin was therefore skipped. Eb (tilt switch) The tilt switch is blocked. Mot 2 (rotation sensor) The speed detection is not operating properly. The speed meter is probably out of order or disconnected. Remark When a malfunction occurs during a program, the central display will communicate the appropriate error message at the end of the cycle.
Maintenance of the machine General maintenance Periodical maintenance 7 ❐ Clean the entire cabinet of the machine regularly and remove all traces of soap, etc.... ❐ ❐ ❐ Remove all detergent residue in the soap dispenser with hot water. Clean the door gasket and remove all detergents and other products. Shut off the main water, steam and power connections at the end of each day. Do not change the setting of the water inlet taps on boiler fed machines once these have been installed.
7 Repair and after-sales service ❐ In case of important malfunctions and deficiencies which you cannot resolve yourself, do not hesitate to contact the technical service of your distributor. Data distributor: Name: .................................................................................... Address: ................................................................................ Tel.: ........................................................................................ Data machine: Type: ....
