Installation Mighty Mite and Super Laundry Presses Refer to Page 3 for Model Numbers SCR1529C SCR1529C Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) An LSG Company 831 South First Street, P.O. Box 32270 Louisville, KY 40232-2270 Phone: (502) 587-1292 Sales Fax: (502) 585-3625 Service/Parts Fax: (502) 681-1275 www.cissellmfg.com Part No.
Table of Contents Model Identification ........................................................................... 3 Safety Information.............................................................................. Explanation of Safety Messages........................................................... Important Safety Instructions ............................................................... 5 5 5 Introduction.........................................................................................
Notes 2 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT AJ1031
Model Identification Information in this manual is applicable to the following models: LDBB (CMMBB) LDCC (CMMCCY) AJ1031 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 3
Notes 4 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT AJ1031
Safety Information Explanation of Safety Messages Important Safety Instructions Precautionary statements (“DANGER,” “WARNING,” and “CAUTION”), followed by specific instructions, are found in this manual and on machine decals. These precautions are intended for the personal safety of the operator, user, servicer, and those maintaining the machine. Save These Instructions DANGER Indicates an imminently hazardous situation that, if not avoided, will cause severe personal injury or death.
Safety Information Safety signs and labels are also placed on the press. Those signs and labels are limited messages. Where needed, further explanations are provided in the manual. These signs are to be inspected for readability and replaced when missing, damaged or unreadable. Refer to Operation/Maintenance Manual for inspections process. Refer to parts manual for ordering information. 12. Replace worn power cords and/or loose plugs. 13. Never operate the press with any guards and/or panels removed. 14.
Introduction Nameplate Location Parts Ordering Information A nameplate is located at the right side of the unit and on the pressure arm. Always provide the machine’s serial number and model number when ordering parts or when seeking technical assistance. If literature or replacement parts are required, contact the source from which the machine was purchased or contact Cissell at (502) 587-1292 for the name and address of the nearest authorized parts distributor.
Notes 8 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT AJ1031
Installation Front View – Typical Laundry Press 1 10 9 2 8 3 7 4 5 6 SCR95N 1 2 3 4 5 Pressure Arm Right Head CLOSE Pushbutton Timer (Optional on some models) Air Filter/Regulator/Lubricator and Downstream Relieving Air Shut-Off and Lockout Valve Frame 6 7 8 9 10 Front Cover Head OPEN Pushbutton Left Head CLOSE Pushbutton Buck and Padding Head Figure 2 AJ1031 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 9
Installation Front View – Typical Laundry Collar and Cuff Press 1 9 10 2 2 3 3 8 7 4 6 5 SCR548N SCR548N 1 2 3 4 5 Pressure Arm Cuff Buck Close Pushbutton Timer Control Box Air Filter/Regulator/Lubricator and Downstream Relieving Air Shut-Off and Lockout Valve 6 7 8 9 10 Cover Open Pushbutton Yoke Rest Head Collar Buck Figure 3 10 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT AJ1031
Installation Rear View – Typical Laundry Press 8 1 7 2 6 3 5 B0158 4 SCR96N 1 2 3 4 Head Steam Outlet Buck Steam Outlet Rear Cover Anchor Bolt Holes 5 6 7 8 Air Inlet Electrical Hook-Up (With optional timer) Steam Inlet Pressure Arm Figure 4 AJ1031 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 11
Installation Dimensions and Specifications Laundry Press Net Weights Supply Requirements Weight Steam (Max. Pressure 115 psig [7.9 bar]) Air lbs. kg cu. ft. (cu. m) free air/cycle @ 80 psig (5.5 bar) LDCC 370 168 1 (.03) .75 (7.35) 26 (12) LDBB 370 168 1 (.03) .75 (7.35) 26 (12) Model BHP (kw) @ 115 psig (7.9 bar) lbs. (kg) conds/hr Table 1 Electrical Requirements (Presses With Timers Only) NOTE: Presses without timers do not require electric hook-up.
Installation Overall Dimensions and Connecting Data 36-7/8 in. (93.7 cm) HEAD OPEN CLOSE OPEN 38 in. (96.5 cm) CLOSE 1-1/2 in. TYP (3.8 cm) 16 in. (40.6 cm) 53 in. (134.6 cm) HEAD OPEN HEIGHT STEAM INLET 34 in. (86.4 cm) 1 in. TYP (2.5 cm) 23 in. (58.5 cm) 2 in. (5.1 cm) 20 in. (50.
Installation 4-3/4 in. (12 cm) 4, 5 1-1/2 in. (3.8 cm) 1-1/2 in. (3.8 cm) 1-1/2 in. (3.8 cm) 3 3-3/4 in. (9.5 cm) 1 5-1/2 in. (14 cm) 1-1/8 in. (2.9 cm) 2 18-1/4 in. (46.4 cm) B0167B SCR98N Figure 6 Item Above Flat Floor Description inches cm Connection 1 Electrical Connection (for presses with timer ONLY) 12 30.5 Refer to Table 2 2 Air Inlet 11 28 1/4 NPT-F 3 Steam Inlet 21.63 55.0 1/2 NPT-F 4 Buck Steam Outlet 21.25 54.0 1/2 NPT-F 5 Head Steam Outlet 23.25 59.
Installation Dimensions of Bucks Without Padding 8-1/4 in. (21 cm) 6-1/2 in. (16.5 cm) 13 in. (33 cm) 20-1/2 in. (52 cm) 90° LDCC COLLAR, CUFF & YOKE PRESS 30-1/2 in. (77.4 cm) 10-3/4 in. (27.3 cm) 13-3/4 in. (34.
Installation Required Materials NOTE: Applicable codes, ordinances, specifications and/or other governing data related to installation must be complied with. The materials listed in Table 4 MAY or MAY NOT conform to these requirements. Quantity Description Source 1 Models with timer ONLY. Lockout type fused disconnect switch suitable for electric service connected to press (refer to wiring schematic in control box). Not required if circuit breaker is used. Local As required Models with timer ONLY.
Installation Location Requirements NOTE: If a forklift is used to move press, exercise care that forklift arms are inserted under frame and DO NOT CONTACT ANY OPERATING MECHANISM. Moving press to installation location while still attached to skid is recommended. However, press can be removed from skid before moving. Removing Press from Skid Unscrew four shipping screws from attaching holes. Using a forklift, lift press and remove skid.
Installation Connecting Air Service NOTE: Failure to provide clean, dry air to press WILL cause premature valve FAILURE and UNNECESSARY DOWNTIME. (Refer to Figure 8) Air service connected to press must have a MINIMUM constant pressure of 80 psig (5.52 bar) and be of ample volume to meet requirements listed in data table (refer to Table 1). Air pressure should be reduced to 75 to 80 psig (5.17 to 5.52 bar) at air inlet regulator.
Installation Connecting Electrical Service • Check all bolts, nuts, screws, tru-arc rings, terminals and fittings for security and tighten as required. (Presses With Timers Only) The following steps outline the procedure for connecting electric service: 1. Install a suitably sized fused disconnect switch or circuit breaker as close to press as practical. 2. Remove one knockout plug from electrical connection box. 3. Connect proper size conduit encased wires to wires inside box.
Installation Steam Check-Out Electrical Check-Out Slowly open shut-off valves in steam SUPPLY and RETURN lines to prevent water hammer in steam pipes. (Presses With Timers Only) 1. Check all steam lines for leaks. 2. Allow press to heat for 15 minutes. 3. Check head surface temperature with a pyrometer or temperature stick measuring device. Temperature should be 300°F to 340°F (150°C to 172°C). 20 Close electrical disconnect switch or circuit breakers. 1. Place timer switch to ON position. 2.