OWNER'S MANUAL 170 lb. HD LAUNDRY DRYER Gas: Natural and LP Steam Technical specifications Installation instructions Operating instructions Maintenance HD170 Cissell Manufacturing Co. 831 S. First St. - P.O.Box 32270 - Louisville, Ky.
IMPORTANT NOTICES—PLEASE READ For optimum efficiency and safety, we recommend that you read the Manual before operating the equipment. Store this manual in a file or binder and keep for future reference. WARNING: For your safety, the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury, or loss of life. - Do not store or use gasoline or other flammable liquids or vapors in the vicinity of this or any other appliance.
IMPORTANT NOTICES—PLEASE READ WARNING: To avoid fire hazard, do not dry articles containing foam rubber or similar texture materials. Do not put into this dryer flammable items such as baby bed mattresses, throw rugs, undergarments (brassieres, etc.) and other items which use rubber as padding or backing. Rubber easily oxidizes causing excessive heat and possible fire. These items should be air dried. WARNING: Synthetic solvent fumes from drycleaning machines create acids when drawn through the dryer.
IMPORTANT NOTICES—PLEASE READ ATTENTION: L’ACHETEUR DOIT PLACER L’AVERTISSEMENT SUIVANT DANS UN ENDROIT CLAIR ET VISIBLE: AVERTISSEMENT. Assurez-vous de bien suivre les instructions donnees dans cette notice pour reduire au minimum le risque d’incendie ou d’explosion ou pour eviter tuot dommage materiel, toute blessure ou la mort. __ Ne pas entreposer ni utiliser d’essence ni d’autres vapeurs ou liquides inflammables dans le voisinage de cet appareil ou de tout autre apparell.
CISSELL WARRANTY The Cissell Manufacturing Company (Cissell) warrants all new equipment (and the original parts thereof) to be free from defects in material or workmanship for a period of three (3) years from the date of sale thereof to an original purchaser for use, except as hereinafter provided.
TABLE OF CONTENTS PAGE Model Numbers & Company Address .................................................................................. 1 Important Notices .............................................................................................................. 2-4 Dryer Warranty .................................................................................................................... 5 Table of Contents ......................................................................................
TABLE OF CONTENTS Air Switch Assembly .......................................................................................................... 65 Two Timer Control Panel Assembly .................................................................................... 66 DMP Control Panel Assembly ............................................................................................ 67 Pro Control Panel Assembly .............................................................................................
SYMBOLS The following symbols are used in this manual and/or on the machine.
SYMBOLS Symbol Description rotation in two directions rotation dans les deux sens Drehbewigung in zwei Richtungen movimiento rotativo en los dos sentidos direction of rotation sens de mouvement continu de rotation Drehbewegung in Pfeilrichtung movimiento giratorio o rotatorio en el sentido de la flecha End of Cycle caution attention Achtung atencion; precaucion Page 9
UNPACKING/GENERAL INSTALLATION (ALL DRYERS) UNPACKING This dryer is packed in a large wooden crate. Upon arrival of the equipment, any damage in shipment should be reported to the carrier immediately. Upon locating permanent location of a unit, care should be taken in movement and placement of equipment. See outline clearance diagrams for correct dimensions. Remove all packing material such as: tape, manuals, skid, etc. Leveling: Use spirit level on top of dryer.
GENERAL INSTALLATION (ALL DRYERS) IMPORTANT Provide adequate clearance for air openings into the combustion chamber. GENERAL Replacement parts for this dryer are available from your distributor or by contacting the factory at the address or phone number printed on the cover of this manual. 1 . Unscrew two (2) front cover panel hold-down screws and open the front cover panel. If wires enclosed are not color coded or numbered, mark wires before disconnecting. Refer to the wiring diagram.
GAS DRYER DIMENSIONS Page 12
STEAM DRYER DIMENSIONS Page 13
DRYER SPECIFICATIONS GENERAL SPECIFICATIONS FOR 150 lb. DRYERS Floor Space ............................................ 64” (1626 mm) Deep x 54” (1372 mm) Wide x 96” (2439 mm) High Doors .................................................... 31-1/4” (794 mm) Diameter Basket Size .......................................... 50” (1270 mm) Diameter x 42” (1067 mm) Deep Basket Capacity (Dry Weight) ........ 150 lbs. (68.0 kg) Dryweight Basket Motor ...................................... 1-1/2 HP (1.
DRYER SPECIFICATIONS STEAM HEATED DRYERS ONLY Operating Steam Pressure 100 psig (6.9 bar) Maximum Boiler HP 12.5 HP (9.33 kW) Heat Capacity 8 Coil Steam Coils (4) 6”(153 mm) x 10 1/4” (261 mm) x 40 1/2”(1029 mm) Steam Supply Connection 3/4” (20 mm) Steam Return Connection 3/4” (20 mm) Trap Connection (2) 3/4” (20 mm) Maximum Air Displacement 2250 cfm (63.
ELECTRICAL CONNECTIONS (WITH GROUNDING INSTRUCTIONS ELECTRICAL CONNECTIONS FOR ALL DRYERS Dryers must be electrically grounded by a separate #14 or larger green wire from the grounding terminal within the service connection box, to a cold water pipe. In all cases, the grounding method must comply with local electrical code requirements; or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or the Canadian Electrical Code, CA C22.1—Latest Edition.
GAS PIPING GAS SERVICE INSTALLATION INFORMATION The size of the gas service pipe is dependant upon many variables, such as tees, lengths, etc. Specific pipe size should be obtained from the gas supplier. Refer to the Gas Pipe Size Chart in this manual for general gas pipe size information. CAUTION Gas loop piping must be installed as shown in Illustration, to maintain equal gas pressure for all dryers connected to a single gas service. Other gas using appliances should be connected upstream from the loop.
GAS PIPING INSTALLATION (ILLUSTRATION) Page 18
GAS PIPE SIZE CHART TOTAL BTU/HR (for LP Gas correct total Btu/h below by multiplying by .6) TOTAL KCAL HOUR GAS PIPE SIZE FOR 1000 Btu (252 kcal/h) NATURAL GAS AT 7” w. c. (17.5 bar) PRESSURE In figuring total length of pipe, make allowance for tees and elbows. (25 ft.) (50 ft.) (75 ft.) (100 ft.) (125 ft.) (150 ft.
GAS PIPING INSTALLATION GAS PIPING INSTALLATION 1. The installation must conform to local codes or in absence of local codes, with the National Fuel Gas Code, ANSI Z223.1 or the CAN/CGA-B149, Installation Codes. 2. Check with utilities for proper gas pressure and gas supply line. 3. Check the altitude elevation of dryer. 4. The dryer and its individual shut-off valve must be disconnected from the gas supply piping system at test pressures in excess of 1/ 2 psig (.04 bar). 5.
Steam Dryers - Option Installation Instructions (When The Steam Bonnet Is Shipped Separate) STEAM DRYERS -OPTION INSTALLATION INSTRUCTIONS 1. The dryer comes in two wood crates: A - Very large crate B - Smaller crate 2 . Open Crate A and lift dryer off the skid and set in place. 3 . Open Crate B. It contains two assemblies: I - Control Box Assembly II - Steam Bonnet Assembly 4 . Place II - Steam Bonnet Assembly on top of the dryer and slide piped end to rear of dryer.
I - Control Box Assembly and II - Steam Bonnet Assembly (When The Steam Bonnet Is Shipped Seperate) I - Control Box Assembly II - Steam Bonnet Assembly Page 22
STEAM PIPING - INSTALLATION INSTRUCTIONS STEAM PIPING INSTALLATION INSTRUCTIONS 1. Set and anchor dryer in position. Machine should be level assure proper steam circulation. 2. To prevent condensate draining from headers to dryer, piping should have a minimum 12” (305 mm)above respective header. Do not make steam connection to header with a horizontal or downwardly facing tee or elbow. 3. Whenever possible, horizontal runs of steam lines must drain, by gravity, to respective steam header.
STEAM PIPING INSTALLATION INDIVIDUALLY TRAPPED COILS ARE RECOMMENDED RATHER THAN MANFOLDING RETURN INTO ONE TRAP.
DRYER INSTALLATION WITH MULTIPLE EXHAUST For Exhaust Duct less than 14 feet (5 m) and 2 elbows equivalent and less than 0.3 inches (.8 mbar) static pressure. DRYER EXHAUSTS Area of section “A-A” must be equal to the sum of dryer exhaust pipes entering multiple exhaust pipe. (See chart below.) MODELS: HD150 No.
DRYER INSTALLATION WITH MULTIPLE EXHAUST (ILLUSTRATION) Page 26
DRYER INSTALLATION WITH MULTIPLE EXHAUST EXHAUST INSTALLATION— MULTIPLE MANIFOLD DUCT For Exhaust Duct more than 14 feet (5 m) and 2 elbows equivalent and more than 0.3 inches (8 mm) static pressure. 1. Make-up air from outside building may enter enclosure from top or side walls. (See Dryer Make-Up Air Requirements Chart) 2. Use constant diameter duct with area equal to the sum of dryer duct areas. EXAMPLE: 6-8 in. (153-204 mm) diameter duct = 1-19.6 in. (26-498 mm) diameter duct in area. Use 20 in.
SUGGESTED MINIMUM DRYER MAKE-UP AIR REQUIREMENTS Dryer Model Dryer Pocket Capacity lb kg HD30 ST 30 13.6 HD75 ST 75 34 HD110.1 110 50 HD110.1 E/S 110 50 HD125.1 125 56.7 HD150.1 150 68 HD175.1 175 79.4 HD190.1 190 86.2 HD20.1 20 9.1 HD30SL 30 13.6 HD30.1 30 13.6 HD50.1 50 22.7 HD75.1 75 34 HD80.1 80 36.3 Maximum Air Flow Duct Size For Required Make-up Rate per Pocket Service Connection Air Area per Pocket cfm m3/h inch mm sq.
DRYER INSTALLATION WITH SEPARATE EXHAUST (PREFERRED) DRYER INSTALLATION WITH SEPARATE EXHAUST (PREFERRED) DRYER INSTALLATION WITH SEPARATE EXHAUST (PREFERRED) For Exhaust Duct less than 14 feet (5 m) and 2 elbows equivalent and less than 0.3 (8 mm) inches static pressure. NEVER exhaust the dryer into a chimney. NEVER install wire mesh screen over the exhaust or make-up air area. NEVER exhaust into a wall, ceiling, or concealed space. 1.
DRYER AIR FLOW INSTALLATION DRYER AIR FLOW INSTALLATION Nothing is more important than air flow for the proper operation of a clothes dryer. A dryer is a pump which draws make-up air from the out-of-doors, through the heater, through the clothes and then forces the air through the exhaust duct back to the out-ofdoors. Just as in a fluid water pump, there must be a fluid air flow to the inlet of the dryer, if there is to be the proper fluid air flow out of the exhaust duct.
RULES FOR SAFE OPERATION OF DRYER RULES FOR SAFE OPERATION OF DRYER 1. Be sure your dryer is installed properly in accordance with the recommended instructions. 2. CAUTION Be safe—shut main electrical power supply and gas supply off externally before attempting service. 3. CAUTION Never use drycleaning solvents: gasoline, kerosene, or other flammable liquids in the dryer. Fire and explosion will occur. Never put fabrics treated with these liquids into the dryer. Never use these liquids near the dryer.
ENERGY SAVING TIPS ENERGY SAVING TIPS 1. Install dryer so that you can use short, straight venting. Turned elbows and long vent tubing tend to increase drying time. Longer drying time means the use of more energy and higher operating costs. 2. Operate dryer using full-size loads. Very large loads use extra energy. Very small loads waste energy. 3. Dry light-weight fabrics separately from heavy fabrics.
OPERATING INSTRUCTIONS—TWO TIMER MODELS Page 33
OPERATING INSTRUCTIONS—TWO TIMER MODELS OPERATING INSTRUCTIONS—TWO TIMER MODELS OPERATINGINSTRUCTIONS—TWO TIMERMODELS 1. After loading the dryer with the water washed clothes load, close the loading door. For better drying, do not load dryer with combination of garments that twist. 2. Turn the 60-minute drying timer to the desired drying time. The drying cycle light will be on and indicate the drying. The light shuts off when drying time is complete. (figure 1 on page 31.) 3.
OPERATING INSTRUCTIONS—TWO TIMER MODELS OPERATING INSTRUCTIONS—TWO TIMER MODELS OPERATINGINSTRUCTIONS—TWO TIMERMODELS (continued) What is happening to the drying operation: a. The fan motor will operate. b. The basket will rotate. c. The heat source will be energized. d. The heated air will mix with the water washed clothes to evaporate the moisture from the garments. e. The thermostats will function to maintain a safe temperature throughout the drying cycle. f.
SERVICE SAVERS TROUBLESHOOTING DRYER WON’T START To help you troubleshoot the dryer, listed below are the most common reasons for service calls and some answers to the problems. Before you call service, please review the following items: 1. 2. 3. 4. 5. 6. Is the door completely closed? Are the controls set to the “ON” or “I” position? Did you push the “start” control? Has a fuse blown or a circuit breaker tripped? Are the fuses tight? Check for low voltage. DRYER WON’T HEAT 1.
TROUBLESHOOTING CHART TROUBLE Motor will not start. CAUSE REMEDY Check fuses on circuit breakers. Make sure main control switch is ON. Check power source; voltage, phase and frequency must be the same as specified on electrical rating plate. Turn timer clockwise to desired time setting. Check wire connections in electrical box on rear of dryer. No power. Incorrect power. Motor tripping on thermal overload. Time off. Loose wiring connections. Defective starting relay. Low voltage.
TROUBLESHOOTING CHART TROUBLE Dryer runs, but no heat. CAUSE Incorrect voltage. No voltage. Lint Door open. Defective gas valve. Gas turned off. Line fuse or heater circuit fuse blown to unit. Defective door switch. Spark igniter not igniting gas. Air switch not operating. Air switch out of adjustment. Air switch defective. Gas pressure too low. Improper orifice. Electric power to heating unit turned off. Defective relay. Defective thermostat. Defective safety Overload Thermostat.
TROUBLESHOOTING CHART TROUBLE Main burners burning improperly. Main burner cycles on and off. Low or high gas flame. Dryer too hot. Dryer does not stop at end of time period (6). Dryer runs no steam to coils. CAUSE REMEDY Dirt in burner. High gas pressure. Orifice too large. Restricted or blocked exhaust. Defective ground. Blow out. Adjust gas pressure per rating plate. Send to factory for correct orifices. Clean exhaust. Incorrect main burner orifices. Incorrect main burner orifice.
DIRECT-SPARK IGNITION OPERATION DIRECT SPARK IGNITION OPERATION NOTE: Some models are equipped with a dual ignition system. The dual ignition system contains two Direct Spark Ignition modules in parallel. Each module has its own Flame Sense circuit and acts independently of the other. If either Bonnet Limit Thermostat opens because of high heat or flame impingement, the entire ignition system will shut down. 1.
DIRECT SPARK IGNITION OPERATION FLOW CHART Page 41
MAINTENANCE—GENERAL DAILY CLEAN LINT TRAP DAILY. Remove lint before starting day’s operation. A clean lint trap will increase the efficiency of the dryer, as the moisture-laden air will be exhausted more quickly. DRYER AREA. Keep dryer area clean and free from combustible materials, gasoline and other flammable vapors and liquids. SLIDING DOORS. Check track for foreign objects. WEEKLY UNITS HEATED BY STEAM. Keep steam coils clean. Check periodically and clean often, as required.
BURNER AIR INLET ADJUSTMENT BURNER AIR INLET ADJUSTMENT Page 43
BASKET ALIGNMENT FOR DRYERS WITH TM200 GEAR REDUCER Page 44
BASKET ALIGNMENT FOR DRYERS WITH TM200 GEAR REDUCER INSTRUCTIONS FOR ALIGNING BASKETS ON 110 LB. DRYERS INSTRUCTIONS 1. Loosen bolts number one (1) through five (5). 2. Place pin “A” in position shown in figures 1 and 2. 3. Check pins “B” at position shown in figures 1 and 2 for equal clearance. 4. If pin “B” clearance is unequal, adjust at nut #6. 5.
BASKET ALIGNMENT FOR DRYERS WITH GEAR MOTOR Jacket Rear View BASKET TOO LOW If there are shims under Bearing B; 1. Loosen bolts 2. Remove shim(s). 3. Tighten bolts - check alignment. If there are no shims under B; 1. Loosen bolts on bearing A. 2. Add shim(s) under bearing A. 3. Tighten bolts - check alignment 4. Repeat until aligned. BASKET TOO HIGH If there are shims under A; 1. Loosen bolts 2. Remove shim(s). 3. Tighten bolts - check alignment. If there are no shims under A; 1.
SHIMMING THE BASKET AND SPIDER ASSEMBLY This procedure is normally necessary when replacing either the basket INSTRUCTIONS FOR SHIMMING THE BASKET or the spider assembly on any dryer. The alignment of these two parts AND SPIDER ASSEMBLY are crucial in assuring a true running basket. A. Align the basket as per instructions on the previous page. B. Rotate the basket to determine where the most out-of-round point is (where the basket scrapes or comes closest to scraping the sweep sheet). C.
AIR SWITCH ADJUSTMENT AIR SWITCH ADJUSTMENT 1. Shut off current; disconnect leads and remove air switch. 2. Lay air switch assembly on flat surface. Adjust air blade at “A” (figure 1) so that air blade lays flat and surface “B” is parallel to the flat surface. 3.
DRYERS WITH REVERSING CONTROL TIMER INSTRUCTIONS FOR DRYERS WITH REVERSING CONTROL TIMER Instructions In operation, coasting of basket increases, making it necessary to readjust reversing timer. CAUTION Failure to do this will cause the thermal overload units for the basket to cut-out unnecessarily and probably damage the gear reducer. Adjustment of reversing timer dwell time CAUTION Dryer power supply must be shut off before adjusting timer.
DRYERS WITH REVERSING CONTROL INSTRUCTIONS FOR DRYERS WITHOUT REVERSING CONTROL FAN AND BASKET ROTATION Instructions NOTE Fan rotates counter-clockwise as viewed from back end of motor. See arrow on motor support. Basket rotates counter-clockwise as viewed from back end of motor. See arrow on motor support. Basket rotates clockwise as viewed from front of tumbler. To change rotation of both fan and basket, reverse power leads L1 and L2. To change rotation of fan only, reverse motor leads F1 and F2.
LARGE GEAR REDUCER MAINTENANCE LARGE GEAR REDUCER MAINTENANCE LARGE GEAR REDUCER MAINTENANCE Before placing the dryer in operation, check the oil level. If the oil level is correct, it can be checked by removing the fill overflow plug on the right hand side of the gear reducer (facing rear). If oil must be added, remove the pop-off valve at the top of the gear reducer and add as needed. CHANGE OIL ONCE EVERY 6 MONTHS. WARNING: Oil level shall not exceed 52 oz.
FRONT VIEW Ref. No. 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Part No.
REAR VIEW (TM200 GEAR REDUCER) r. oto rM ea G To See following page for part numbers.
REAR VIEW (TM200 GEAR REDUCER) 1 3 5 6 7 8 9 10 11 12 13 14 15 16 18 19 20 21 22 23 24 25 26 27 28 29 31 32 TUX415 TU8206 TU9663 TU3807 TU14092 TU2363 TU9751 TU6081 TU2007 TU9615 TU470 TU6633 TM200 TU5328 TU4626 TU2473 TU6086 TU4791 TU2372 CFB2100 TU6026 TU13834 TU6028 500300644 TU7130 TU7131 SB170 TU4684 TU7733 33 34 35 36 TU7517 TU2831 TU1851 TU2195 37 38 39 40 41 TU455 TU3575 TU5312 TU4787 TU5439 43 44 45 46 47 48 49 50 52 53 Air Switch Cover Air Switch Assembly Gear Sheave (50/60 Hz.
REAR VIEW (GEAR MOTOR) r. oto M ar Ge o T To r. oto nM Fa See following page for part numbers.
REAR VIEW (GEAR MOTOR) 1 3 5 6 7 8 9 10 11 12 13 14 15 16 18 19 20 21 22 23 24 25 26 27 28 29 32 TUX415 TU8206 TU3418 TUX328 TU16046 TU16091 TU16085 TU16043 TU16064 TU16042 TU16021 TU16062 TUX454 TU16079 TUX575 TU2881 TU2473 TU6086 TU4791 TU2372 CFB2100 TU16092 TU13834 TU16016 500300644 TU7130 TU7131 SB170 TU7733 54 55 Air Switch Cover Air Switch Assembly Washer, Lock, 5/8” Nut, Hex, 5/8-11 Beltguard Belt, BX47 (60 Cycle) Belt, BX46 (50 Cycle) Pulley, 3B86 (60 Cycle) Pulley, 3B80 (50 Cycle) Sheave, 3B44
TU15449 FRONT PANEL ASSEMBLY * * * Cover plate used for DMP and PRO HC. Ref. No. Part No. Description 1 2 3 4 5 6 7 8 9 10 11 12 EA-00652-0 SB-00975-0 PIF172 TU15448 TU14483 TU2236 TU2686 TU2687 TU2836 TU3209 TU3212 TU3785 Reed Switch #6-32 Screw Hinge post bearing Front panel (Specify color) Loading door (Specify color) Hinge post #8-32 Pan Hd. screw #8 Ph. Hd. screw 5/16-18 H.H. screw #14 Pan Hd. screw 5/16 Lock washer #8 E.T. Cup washer Page 57 Ref. No. Part No.
THERMOSTAT ASSEMBLY - 2 TIMER Ref. No. Part No. Description TU6030 Assembly, Thermostat 1 TU5530 Mounting Bracket 2 TU1980 Thermostat 3 TU3593 Thermometer TU3816 Lens Replacement (Texas Gage ONLY) TU8475 Lens Replacement (Marshaltown Inst. ONLY) TU11193 Lens Replacement (Weiss—consult factory) TU13213 Lens Replacement (Weiss—consult factory) 4 TU490 Thermostat Knob (Fahrenheit) TU491 Thermostat Knob (Centigrade) 5 TU3209 #14 x 5/8” S.M.S.
BURNER ACCESS DOOR Ref. No. Part No. Description TU14624 - Burner Access Door complete (Specify color) 1 2 3 4 5 6 CA-13098-0 SB-00951-0 TU14622 TU14623 TU14662 TU5739 Gasket, DR dryer control doors Screw,#8 X 7/16" Philips F.H.
LINT DOOR ASSEMBLY Ref. No. Part No. Description TU14627 Lint Door Complete (Specify color) 1 2 3 4 4a 5 6 5 8 LA-00123-0 SB-00836-0 SB-00949-0 TU14594 TU15410 TU14626 TU14529 TU14530 TU14640 Latch Screw, Pancake Fastener, Kickplate Label, English Label, 5 Language Lint Door Welded Asm. (Specify color).
DMP SENSOR ASSEMBLY Ref. No. Part No.
2 TIMER SENSOR ASSEMBLY Ref. No. Part No.
PRO SENSOR ASSEMBLY Ref. No. 1 2 3 4 5 6 7 Part No. Description ESA-00940-0 Sensor Assembly 254/00009/10 CA-23067-0 EA-00411-0 SB-00828-0 SB-00952-0 TU3266 TU3400 Thermistor Thermostat Switch, 220 Degrees Screw, Mach. P.H. #8-32 X 1/2 Screw, P.H.
PROHC SENSOR ASSEMBLY - UPPER and LOWER Ref. No. Part No. Description TU14724 PROHC Sensor assembly (upper) 1 2 3 4 5 6 SB-00952-0 TU14693 TU14694 TU3400 TU7733 254/00060/00 Screw, #6-32x 3/8” long Mounting plate upper probe Cover plate, probe Nut, #6-32 Screw, self drill #8-18x 1/2” long Humidity sensor UPPER ASSEMBLY Ref. No. LOWER ASSEMBLY Part No.
AIR SWITCH ASSEMBLY Ref. No. Part No.
2 TIMER CONTROL PANEL ASSEMBLY Ref. No. Part No. Ref. No. Description Part No.
DMP CONTROL PANEL ASSEMBLY Ref No. Part No.
PRO CONTROL PANEL ASSEMBLY Ref. No. 1 2 3 4 5 6 7 8 9 10 Part No.
PROHC CONTROL PANEL Ref. No. 1 2 3 4 5 6 7 8 9 Part No.
REAR MOTOR CONTROL ASSEMBLY Ref. No. 1 2 3 4 5 6 7 8 9 Part No. Description TU13700 TU13802 TU13514 TU13642 TU2973 TU13516 TU7733 EA-00685-0 TU16101 TU15962 TU14825 TU15592 TU15898 TU16034 Plate, Motor Control Transformer, 115/208/230 75VA Transformer, 60VA 460V/24V 60VA Transformer, 60VA 575V/24V 60VA Screw, #8 Contactor, 24VAC IEC 12A W/AUX Screw, #8 self drilling Reversing Contactor, 3 POLE/24V COIL/12A Overload, 4.5-6.3 Overload, 2.2-3.2 Surge Suppressor Overload, 2.8-4 Overload, 3.5-5.
PARTS—TM200—LARGE GEAR REDUCER WITH BRONZE TEETH REF NO. PART NO.. DESCRIPTION 1 2 3 4 5 6 7 8 TM203 K474 TM119 TM208 TM225 IB139 TM205 TM204 Housing Oil Level Plug Kit 1/4” Vent Plug Small Bearing Cone & Cup Worm & Worm Gear 3/8” - 16 x 1 1/4” Cap Screw Small Open End Cap Small Klozure REF NO. PART NO.
GAS BONNET AND BURNER ASSEMBLY REF NO. PART NO.. DESCRIPTION TU15763 - Natural Gas Bonnet TU15767 - LP Gas Bonnet 1 2 TU14058 CB36 Gas Manifold 1/4” - 20 x 1/2” Hex Head Screw 3 4 5 6 7 OP267 PT196 RC344 TUX387 TUX352 TUX435 TU6862 TU13613 GA-00764-0 TU4605 3/4” x 1/2” Steel Bushing 3/4” Strap 1/4” - 20 x 3/4” Hex Head Screw BSI Asm. Burner 3/4” Natural Gas Valve 3/4” LP Gas Valve Gas Manifold Nut Bonnet Assembly Direct Spark Ignition Electrode 3/4” Elbow 8 9 10 11 Page 72 REF NO. PART NO.
STEAM BONNET ASSEMBLY—TU14027 REF NO. 1 2 3 4 5 6 7 8 9 10 PART NO.. TU4610 TU4597 TU4608 TU13517 TU4620 TU4605 TU4600 TU4599 TU4791 TU1699 1 1 TU9890 12 TU2846 DESCRIPTION 3/4” x 5” Pipe Nipple 3/4” Tee 3/4” x 2” Pipe Nipple *Steam Solenoid Valve 24V 3/4” x 4 1/2” Pipe Nipple 3/4” Elbow 3/4” Union 3/4” x 18” Pipe Nipple Angle 90° Connector Steam Coils REF NO. PART NO. DESCRIPTION 13 TU2847 14 TU9953 Flat Washer (Pkg.
INSULATION PLACEMENT 1 2 3 4 Ref. Part No. No.
Page 75
