User's Manual

GETTING STARTEDHOW TO USE (Continued)
5. 2.
WATCH
RECORD
REVIEW
TIMER
DELETE
Night Vision OFF / ON
Video Screen
Note: Reception is good in open areas such as arenas, or outdoors on level ground and
away from buildings and transmission towers, poles and wires. Keep a good distance away
from home or business Wi-Fi routers. Keep away from machine rooms.
EyeSpy wireless transmission can suffer from interference caused by other 2.4MHz devices
such as baby monitors, home wireless CCTV security systems and wireless telephones.
Keep away from high voltage cable and towers. Keep away from communication/mobile
stations.
Do not use the units in damp, wet or high temperature conditions.
WATCH – When you press the button with the check mark, the screen will show you what
the EyeSpy Eagle Eye camera is seeing. If you are in low-light conditions and the image is
not clear, you can press the small square button on top of the viewer. This will turn on the
amplified Night Vision circuit which will make the image easier to see, and will impart a slight
green tint to the image.
To take a picture, push the button with the icon of a camera on it. Note: To use this feature
you must have an SD memory card inserted in the viewer, and the switch on the bottom of
the Eagle Eye slid to the left.
RECORD – Note: To use this feature you must have an SD memory card inserted into the
card socket located on the left side of the viewer, as shown in the illustration.
Viewer – Slide the power switch on top of the viewer to the left. The screen will light up and
show the EyeSpy logo. In another second or two the menu will appear as below. To
navigate the menu there are four buttons on the front of the viewer.
EXPLANATION OF THE VIEWER FUNCTIONS
Photo - to take a picture
or start a recording
Next - moves the screen
cursor down to choose
another task
Select - to confirm
chosen function
Back - cancels current
function & goes back
one step to previous function
IMPORTANT SAFETY INSTRUCTIONS AND WARNINGS
For LI-ION / POLYMER BATTERIES
• You should read these safety instructions and warnings before using or charging your battery.
• Never disassemble the viewer or try to remove the battery.
• While generally safe, Lithium-Polymer batteries are volatile. Failure to read and follow the below
instructions may result in fire, personal injury and damage to property if charged or used improperly.
• Lithium-Polymer battery may explode and cause fire if misused or defective.
• When charging the battery, please place it on a fire resistant surface. Do not leave the viewer on
a wood surface or on paper, carpet, or grass. Do not leave the unit unattended while it is
charging. If at any time you witness the viewer starting to swell up, emit smoke or feel hot,
discontinue charging process immediately, disconnect the viewer and observe it in a safe place
for approximately 15 minutes. The battery may be leaking, and the reaction with air may cause
the chemicals to ignite, resulting in fire. In the unlikely event of this occurring, please contact us
via the EyeSpy website www.eyespytoys.com or call our Customer Assistance Line at 1866 469 9686.
• Never store or charge the viewer inside your car in extremely warm temperatures (105ºF or 41ºC),
since extreme temperature could ignite a fire.
• Never drop the viewer, as this may cause a battery to leak.
Eagle Spy:
The helicopter is equipped with a Lithium-Polymer battery that is charged with the included
AC wall-plug adapter/charger. To charge the helicopter battery, please do the following:
A – Ensure that the black slide switch on the bottom
of the helicopter is in the OFF position.
B – Separate the two red connectors by gently, yet
firmly pulling the two red connectors apart.
C – Plug the white connector on the bottom of the
helicopter into the connector at the end of the AC
adapter/charger.
D - Plug the AC adapter/charger into a 110V AC wall
plug and let the battery charge for three hours.
E - After charging, unplug the AC adapter from the
wall plug and disconnect from the Eagle Spy.
F - Reconnect the battery.
2.
B
C
To charge
E
F
To Fly
Viewer:
The viewer’s built-in Lithium Polymer rechargeable 800mAh, 3.7 V,
non-removable battery requires charging before its first use. The
small plug on the included USB cord must be carefully inserted into
the jack on the right-side of the viewer. The larger plug is inserted
into an open USB port, found on most desktop, laptop, and
notebook computers.
Leave the USB cord attached for three hours. After three hours,
disconnect the USB cord. The circular opening next to the USB
connection jack is a 1/8” mini-jack.
Add
USB
Cable
3.
The viewer attaches to the top of the
remote controller as shown in the diagram.
For two person play, the screen can be
detatched for one person to hold control
the Eagle Spy and one person to hold the
viewer.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.