CONFIDENTIAL UNDER CONSTRUCTION User’’ss Manual CV CS Preliminary Edition Ver. 1.
CONFI DENTI AL UNDER CONSTRUCTI ON In order to use safely – Please be sure to follow with the instruction! ・ Be sure to read this manual before put the printer in operation. After that, please keep the manual for the time to reread whenever necessary. ・ Please don't touch, disassemble nor repair any part of the printer other than the part to which this manual instructs.
CONFI DENTI AL UNDER CONSTRUCTI ON Warning ● The following action has possibilities to make the printer be damaged, broken down, or heated, and fumed. So do not carry out by any means, since it becomes the cause of a fire and an electric shock. When any damage and/or serious trouble happens, please switch off the printer and pull out a power plug from a wall socket, and ask supplier for their help. · Please don't drop, step on, give strong pressure or a strong shock on the printer.
CONFI DENTI AL UNDER CONSTRUCTI ON Gener al not i ce 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. In use of the printer, please read out "in order to use safely" in advance well and follow with it's instruction. Be careful not to drop a clip or a thing like a pin into the printer. It becomes the cause of failure. Be careful of movement and carrying of the printer enough. If the printer is dropped, there is a possibility of damaging body and/or anything others.
CONFI DENTI AL UNDER CONSTRUCTI ON Not i ce f or t he i nst al l at i on 1. In use of the printer, please read out "in order to use safely" in advance well and follow with it's instruction. 2. Please don't use the printer in the places where temperature is unusually high, such as near the place with fire or moisture, the place where direct rays hit, a heating instrument, or a heat instrument, a low place, and a place of high humidity and dusty. 3.
CONFI DENTI AL UNDER CONSTRUCTI ON - Europe Code set No 764S (60000960) Part number Rating Plug 203 10 / 16A 250V Code H05VV-F 1.00mm23G Connector EF-28 250V 10A Acquisition standard No. EN60799 EN60799 EN60799 Code set No 764S (60001030) Part number Rating Plug KP-4819Y 10 / 16A 250V Code H05VV-F(GTCE-3) 1.00mm23G Connector KS-31A 250V 10A 5 Acquisition standard No. IEC60884 IEC60227-5 IEC60320-1 Hei wa Tokei MFG. CO. , LTD.
CONFI DENTI AL UNDER CONSTRUCTI ON Regul at or y compl i ance st at ement s American users FCC part 15 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
CONFI DENTI AL UNDER CONSTRUCTI ON 日本のお客様へ/Japanese Users 電波障害について この装置は、情報処理装置等電波障害自主規制協議会(VCCI)の基準に基づく クラス B 情報技術装置です。この装置は、家庭環境で使用することを目的としていますが、 この装置がラジオやテレビジョンの受信機に近接して使用されると、受信障害を引き起こす 可能性があります。 取扱説明書に従って正しい取り扱いをしてください。 VCCI statement This equipment is in the Class B category (information Technology Equipment to be used in a residential area or an adjacent area thereto) and conforms to standards set by the Voluntary Control Council for interference by information Technology Equipment aimed at preven
CONFI DENTI AL UNDER CONSTRUCTI ON Chapter 1 Printer Setup 1. 2. 3. 4. 5. 6. 7. Please check the contents of supplied Name of each part Connect Power cable Connect Host computer (PC) The way to set Paper Cut Off Box Check of Paper and Ribbon Paper and Ribbon mounting 8 Hei wa Tokei MFG. CO. , LTD.
CONFI DENTI AL UNDER CONSTRUCTI ON 1. Please check the contents of supplied Please check that the printer and all accessories are packed in without missing. Printer Roll Holder Assy Power Cable Printer Driver CD L-Spacer * Please keep the package box, packing material, etc. for transportation. Caution * * * * Please be careful to move or carry the printer and/or to take the printer out from packing box. In case if the printer is fallen down, it’s possible to make damage your body or anything.
CONFI DENTI AL UNDER CONSTRUCTI ON 2. Name of each part [Front] Exit of printed paper Thermal Print Head Paper Cut Off Box Open Button Roll Holder Assy Ribbon Holder for Receiver [Back] Air Ventilator Platen Roller Ribbon Holder for Supplier USB Cable Port Power Switch Power Supply Caution * In opening paper cover, please work after opening completely. Otherwise, there is a possibility of cover closing, which may damage your body etc. * Please be careful of cover when the cover is opened.
CONFI DENTI AL UNDER CONSTRUCTI ON 3. Connect Power Cable 1. Please confirm that the power switch should be OFF. 2. Inserts the connector of power supply cable in the printer’s power supply inlet. 3. Connects the plug of power supply cable in wall socket. Power supply inlet Power switch Caution * Please use the power cable attached with the printer, and please be sure to ground the grounding terminal of a plug. 4. Connect the Host Computer (PC) 1.
CONFI DENTI AL UNDER CONSTRUCTI ON 5. The way to set Paper Cut Off Box In the Paper Cut Off Box, cut off of unnecessary pieces of paper are stacked. Please remove those cut off whenever paper media is changed. It’s possible to have paper jam if the box is fully stacked. * Easier way to mount the box is to push upper side of the box in the printer slightly.
CONFI DENTI AL UNDER CONSTRUCTI ON 6. Check of Paper and Ribbon Paper Post Card, A5 Wide Size 152 mm L-Size, 2L-Size 127mm Type Post Card, A5 Wide Size L-Size 2L-Size Ribbon i-Media Type Post Card, A5 Wide Size 159 ㎜ L-Size, 2L-Size 134mm L-Size, 2L-Size Post Card, A5 Wide Size 13 Hei wa Tokei MFG. CO. , LTD.
CONFI DENTI AL UNDER CONSTRUCTI ON 7. Paper and Ribbon Mounting 1. Opens front case C by pressing the open button. Open Button 2. Mounts paper on roll holder assy. For L-size and 2L-size, sets L-spacer first. L-Size, 2L-Size Post Card, A5 Wide Size L-Spacer, Roll Holder Assy Roll Holder Assy * Please mount paper on roll holder Assy by the same way with for L-Size and 2L-Size. * Please insert firmly so as not to be any space between side of roll and L-spacer.
CONFI DENTI AL UNDER CONSTRUCTI ON 3. Installs paper in the printer. Fits paper to the position of each paper size, and inserts it to arrow direction until buzzer makes ‘Pi-Pi’ sound. (Around the position to dotted line of photo) LED indicator shall change from Red flicker to Blue & Red flicking. * Please pay attention not to feed paper with deviation nor slanting. * Please refer [Note] of 5. of next page too.
CONFI DENTI AL UNDER CONSTRUCTI ON 4. Installs ribbon in the printer. * By paying attention to front & back of ribbon, mount the ribbon core on each supply and receiving side as shown in below. * Removes ribbon loosing by turning the ribbon attachment of receiving side approx. 5 times to the arrow direction. Please fits color of attachment and holder of printer.
CONFI DENTI AL UNDER CONSTRUCTI ON Chapter 2 Trouble Shoot 1. 2. 3. 4. Error Indication If Paper is jammed If Ribbon is cut out If power was shut down during printing 17 Hei wa Tokei MFG. CO. , LTD.
CONFI DENTI AL UNDER CONSTRUCTI ON 1. Error Indication Status Online Front Cover Open Paper End Ribbon End LED Indication ━━━━━━━━━━ ━━━━━━━━ ━━━━ ━━━━ ━ ━ ━━━━ ━ ━ ━ Solution Printer ready Please close front cover Please set paper correctly Please set new paper Please set new ribbon ※1 ※2 ※2 ※ 1 When paper is set at right position, buzzer sounds ‘Pi-Pi’. ※ 2 Please exchange both paper and ribbon same time together.
CONFI DENTI AL UNDER CONSTRUCTI ON 2. If Paper is jammed 1. Please open the front case C by pressing the open button. 2. Please pull paper out, and cut damaged part straightly and clearly with correct angle, then insert again. Paper edge cutting ○ × If paper edge is not cut correctly, trouble shall be occurred in quality, paper feed. 19 Hei wa Tokei MFG. CO. , LTD.
CONFI DENTI AL UNDER CONSTRUCTI ON 3. If Ribbon is cut out 1. Please open the front case C by pressing the open button. 2. Please remove paper of which print is interrupted by ribbon error from the printer. 3. Ties ribbon by cellophane tape. 4. Mount ribbon in the printer and turns ribbon several times until cellophane tape disappears. Ties by cellophane tape 4. If power was shut down during printing 1. If power is shut down during printing, the front case C is locked to open . 2.
CONFI DENTI AL UNDER CONSTRUCTI ON Chapter 3 After Care 1. Platen Roller Cleaning 2. Thermal Print Head Cleaning 3. Filter Cleaning 21 Hei wa Tokei MFG. CO. , LTD.
CONFI DENTI AL UNDER CONSTRUCTI ON 1. Platen Roller Cleaning Please wipe off powder, garbage, adhesive agent, etc, which comes from ribbon and/or paper and adhering to the platen roller, by ethyl alcohol permeate soft cloth. [Note] Please do not use benzene, thinner or anything other than ethyl alcohol without fail, since it’s possible to invade resin. Please clean by turning the platen roller. Caution * Prior to cleaning, please power OFF the printer and unplug power code without fail. 2.
CONFI DENTI AL UNDER CONSTRUCTI ON 3. Filter Cleaning Please clean filter from time to time or periodically. 1. 2. 3. 4. Please open the front case C by pressing the open button. Removes the filter cover. Use a brush or cleaner to remove dust and debris from the filter. Reinstall the filter with the filter cover up to the cover is hooked completely.
CONFI DENTI AL UNDER CONSTRUCTI ON Appendix 1. Specification Item Model Print Technology Resolution Gray Scale Interface Paper Ribbon General Specification Specification CV Dye Sublimation 334dpi(Paper Feed direction) x 600dpi (TPH width direction) Yellow, Magenta, Cyan 256 steps each USB2.0 (Max. 480Mbps) Buffer size for A5 Wide Size x 2 images Roll paper, Coreless YMC + Overcoat Dimensions 322W x 350D x 276H (mm) Weight 20Kg (Printer hardware only) Power AC100V – 240V 50/60Hz Consumption Max.