CITIZEN User's Manual Model : iDP-460 Dot Matrix Printer Rev.1.00 Newly issued on Feb. 26. 1998 Japan CBM Corporation Information Systems Div.
iDP-460 User’s Manual Declaration of Conformity Manufacturer’s Name : Manufacturer’s Address Declare the Product Product Name Model Number(s) : Japan CBM Corporation : 1-1-7, Okubo, Shinjuku-ku, Tokyo 169-8553, Japan Dot Matrix Printer iDP460 (iDP460P, iDP460R, iDP460V) (S.NO.
iDP-460 User’s Manual IMPORTANT SAFETY INSTRUCTIONS •Read all of these instructions and save them for future reference. •Follow all warnings and instructions marked on the product. •Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. •Do not use this product near water. •Do not place this product on an unstable cart, stand or table. The product may fall, causing serious damage to the product.
iDP-460 User’s Manual WICHTIGE SICHERHEITSANWEISUNGEN •Lesen Sie die nachfolgenden Anweisungen sorgfältig durch und bewahren Sie sie auf. •Befolgen Sie alle auf dem Drucker vermerkten Hinweise und Anweisungen. Vor dem Reinigen grundsätzlich Stecker aus der Steckdose ziehen. Keine Flüssigkeiten oder Aerosolreiniger benutzen. Nut mit einem feuchten Tuch abwischen. •Der Drucker darf nicht in der Nähe von Wasser aufgestellt werden. •Drucker nicht auf einem unstabilen Wagen, Stand oder Tisch aufstellen.
iDP-460 User’s Manual IMPORTANT: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 off FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment.
iDP-460 User’s Manual 1. Prior to using the equipment, be sure to read this User's Manual thoroughly. Please keep it handy for reference whenever it may be needed. 2. The information contained herein may be changed without prior notice. 3. Reproduction of part or all of this User's Manual without permission is strictly prohibited. 4. Never service, disassemble, or repair parts that are not mentioned in this User's Manual. 5.
iDP-460 User’s Manual SAFETY PRECAUTIONS ----- BE SURE TO OBSERVE In order to prevent hazards to an operator or other persons and damage to property, be sure to observe the following precautions. • The following describes the degrees of hazard and damages that can occur if the given instructions are neglected or the equipment is incorrectly operated. WARNING Negligence of this precaution may result in death or serious injury.
iDP-460 User’s Manual WARNING • Never handle the equipment in the following manners, as it may break, become out of order, or overheat causing smoke and resulting in fire or electric shock. If the equipment is used in an abnormal condition, such as when broken, then problems, smoke emission, abnormal odor/noise, and fire can result. If an abnormal condition exists, be sure to turn off the power, disconnect the power plug from a plug socket, and contact our dealer.
iDP-460 User’s Manual PRECAUTIONS FOR INSTALLATION • Do not use or store the equipment in a place exposed to fire, moisture, or direct sunlight, or in a place near a heater or a thermal device where the prescribed operating temperature and humidity are not met, or in a place exposed to much oil, iron powder, or dust. The equipment may become out of order, emit smoke, or catch fire.
iDP-460 User’s Manual PRECAUTIONS FOR HANDLING Do not handle the equipment in the following manners, because problems may result. • Do not use a power supply other than the specified AC adapter. • Do not print when there is no recording paper or ink ribbon set in the equipment. The print head may be damaged • Be careful not to drop foreign substances, such as clips, pins, and screws, into the main body. • Do not spill any liquid or spray any chemical-containing liquid over the equipment.
iDP-460 User’s Manual DAILY MAINTENANCE • Prior to starting maintenance work, be sure to turn off the main body. • Use a dry soft cloth to wipe off stains and dust from the surfaces of the main body case. For severe soiling, dip the cloth in water and wring it, for wiping off the soil. Never use organic solvents, such as alcohol, thinner, trichlene, benzene, ketone, or chemical dusters. • If the equipment is contaminated with paper powder, use a soft brush to clean it.
iDP-460 User’s Manual CONTENTS 1. OUTLINE.................................................................................................................................... 15 1.1 Features ........................................................................................................................................ 15 1.2 Unpacking ..................................................................................................................................... 15 2. BASIC SPECIFICATIONS ...
iDP-460 User’s Manual 7. 6.3.3 Timing Chart .................................................................................................................... 33 6.3.4 Data Receiving Control.................................................................................................... 33 SERIAL INTERFACE ................................................................................................................ 34 7.1 Specifications ..........................................................
iDP-460 User’s Manual <<< German >>> 4. BETRIEB..................................................................................................................................... 54 4.1 Anschluß des Netzteils................................................................................................................. 54 4.2 Anschluß des Schnittstellenkabels.............................................................................................. 55 4.
iDP-460 User’s Manual 1. OUTLINE This is a small-size dot impact printer developed for various data communication terminals, POS terminals, kitchen-use printers, bank card, terminals, and so on. Its abundant built-in features allow you to widely use this printer for different applications. Prior to using it, read and understand this manual thoroughly. 1.
iDP-460 User’s Manual 2. BASIC SPECIFICATIONS 2.1 Model Classification The printer model is classified by the following designation method.
iDP-460 User’s Manual 2.2 Basic Specifications Model iDP 460-RF120 iDP 460-VF120 iDP 460-PF120 Item iDP 460-RF230 iDP 460-VF230 iDP 460-PF230 Print method Serial dot impact method (Bidirectional print) Print width 64mm Print head 7-pin Print speed Approx. 3 lines/sec. (At single color continuous print) Print digits 40 or 42 Columns Character size 1.31mm (W) x 2.4mm (H) Character types Alphanumeric, international characters Line spacing 4.23 mm(1/6 inch) or 2.
iDP-460 User’s Manual 2.3 Paper Specification 2.3.1 Recommended Paper •Type : Normal paper and non-carbon paper •Paper width : 76 ± 0.5 mm •Paper thickness : Single-sheet paper --- 45 to 55 kg/1,000 sheets/1,091 x 788 mm; Copying paper --- Non-carbon paper, 1 original + 1 copy, Total thickness 0.2 mm or less •Roll diameter : Ø83 mm or less •Core : Ø12 mm (Inner Diameter), Ø18 mm (Outer Diameter) 2.3.3 Printing Position Cutter Layout Approx. 20 mm 2.3.
iDP-460 User’s Manual 3.
iDP-460 User’s Manual 4. OPERATION 4.1 Connecting AC Adapter (1)Turn off the Power switch. (2) Connect the cable connector of the AC adapter to the power connector located on the back of the printer. (3) In order to prevent disconnection of the cable connector, put it through a wire saddle, as shown in the figure below. (4) Connect the AC power cord plug to a plug socket. CAUTION : • Use only the specified AC adapter. • Use a different AC power supply from one used for any noise-generating device.
iDP-460 User’s Manual 4.2 Connecting Interface Cable (1) Turn off the power. (Mating side included) (2) Check the top and bottom of the cable terminals, and connect to the interface connector. (3) Fix the cable terminals. •Serial interface: Tighten screws, to fix. •Parallel interface: Turn a stopper, to fix. •Mini DIN interface: Insert until locked. (4) Connect the cable to a computer. 4.3 Connecting Drawer Kick-Out Connector (1) Turn off the power.
iDP-460 User’s Manual 4.4 Setting the Cassette Ribbon (1) Open the printer cover. (2) If the ribbon is slackened, turn the knob in the arrow-indicated direction to give the tension to it before setting. (3) While putting the ribbon in between the head cover and platen, push the locking claws into the holder of the printer. (4) Turn the knob of the cassette ribbon in the arrow-indicated direction to eliminate slackness of the ribbon.
iDP-460 User’s Manual 4.5 Inserting the Paper (1) Put your hands in the concave parts on both sides of the printer cover, and open it until it comes to a stop. (2) Cut the end of the paper roll at close to a right angle. CAUTION : • Be sure to use the specified paper roll. • Use of unspecified paper may adversely affect print quality, printer service life, and so on. • The printer cover is not detachable. Do not apply an excessive force beyond its stopping position.
iDP-460 User’s Manual CAUTION : • If the paper is slack, rewind it, to remove the slack. • If the paper is set slantwise, operate the paper-free lever, to correct the paper position. • While printing, do not hold the paper. This can cause a paper jam.
iDP-460 User’s Manual 4.6 How to Remove Remaining Paper Roll (1) Open the printer cover. (2) Pushing the paper-free lever in the arrow direction, pull out the paper roll. CAUTION : When pulling out the paper (forward/reverse direction), be sure to operate the paper-free lever. 4.7 Removing Paper Jam (1) Open the printer cover. (2) Cut off the paper near the paper inlet slot. (3) Push the paper-free lever in the arrow direction.
iDP-460 User’s Manual 4.8 Operation Panel and Display of Error (1) POWER lamp(green) Illuminated when the power is turned on. (2) ERROR lamp(red) Illuminated when the printer is out of paper or has a printer mechanical error or communication error (serial). •Paper end ----- If the paper runs out, the paper sensor located in the paper course near the print head detects a paper end, turning on the ERROR LED, thus stopping the printer.
iDP-460 User’s Manual 4.9 Print Duty As the printing head mounted onto this printer is not equipped with a head temperature detection sensor (thermistor), the printer protects the printing head against temperature through software. The printer calculates the number of print dots and prints as follows, depending on whether the number of printing dots per line is over or within 500.
iDP-460 User’s Manual 5. DIP SWITCH SETTING 5.1 Location of DIP Switch (1) Turn off the power. (2) Remove a cassette ribbon. The DIP switches are located as shown in the figure below.
iDP-460 User’s Manual 1) DS1 Function ON OFF Setting upon Shipment 1 Font Japan International OFF 2 Auto loading Disable Enable OFF 3 Not available -- -- OFF 4 (*1) Paper used 1P 2P ON Function ON OFF Setting upon Shipment 1 Bit length 7 bits 8 bits ON 2 Parity Yes No ON 3 Parity Even Odd ON 4 At error Prints "?" Ignores the data ON 5 Baud rate 6 Baud rate 7 Baud rate ON 8 Unused OFF 2) DS2 OFF See the table below ON The DS
iDP-460 User’s Manual 6. PARALLEL INTERFACE 6.1 Specifications •Data input system : 8-bit parallel system (DATA1 to DATA8) •Control signals : ACK, BUSY, STB, FAULT •Applicable connectors : Printer side --- 57LE-40360 (Equivalent to anphenol), Cable side --- 57-30360 (Ditto) 6.2 Connector’s Pin Confuguration No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Signal Name No.
iDP-460 User’s Manual 6.3 Input and Output Signals 6.3.1 Input and Output Signals (1) Input signals to the printer • DATA : An 8-bit parallel signal. (Positive logic) • STB : A strobe signal to read the 8-bit data. (Negative logic) (2) Output signals from the printer • ACK : An 8-bit data request signal. A pulse signal output at the end of the BUSY signal.(Negative logic) • BUSY : A signal to indicate the BUSY status of the printer. Input new data when at "LOW.
iDP-460 User’s Manual 6.3.2 Electrical Characteristics (1) Input signal level All the input signals are at the TTL level. "HIGH" level : 2.0 V at minimum "LOW" level : 0.8 V at maximum (2) Output signal level All the output signals are at the TTL level. "HIGH" level : 2.4 V at minimum "LOW" level : 0.4 V at maximum (3) Input and output conditions All the input signals are pulled up at 3.3 kΩ. [Printer Side] [Host Side] All the output signals are pulled up at 3.3kΩ.
iDP-460 User’s Manual 6.3.3 Timing Chart (1) Data input and printing timing T1, T2, T3 : 0.5 µs MIN 6.3.4 T4 : 270 ns MAX T5 : 2.3 µs TYP T6 : 500 ms MIN (At power-on) Data Receiving Control When the BUSY signal is at "LOW," the printer can receive the data from the host, but when at "HIGH," it cannot.
iDP-460 User’s Manual 7. SERIAL INTERFACE 7.
iDP-460 User’s Manual 7.2 Connector’s Pin Configuration D-Sub Connector No. 1 7 3 20 2 4 Mini DIN Connector No. Shell 7 5 3 6 4 Signal I/O FG -GND -RD Input DTR Output TD Output DSR Input D-Sub Connector Function Frame Ground Signal GND Received Data Printer BUSY signal Transmitted Data Data Set Ready Mini DIN Connector Cautions: 1. An RS-232C signal is based on the EIA RS-232C. 2. When the data is not being transferred, the received data should be always maintained as a mark.
iDP-460 User’s Manual 7.3 Input and Output Signals 7.3.1 Input and Output Signals (1) RD This is a serial received data signal. When a framing error, overrun error, or parity error occurs, that data is printed as "?" or discarded. (Depends on DIP switch selection.) The ERROR lamp is illuminated. (2) DTR When this signal is Ready, write the data or a command. an overrun error results, ignoring the previous data.
iDP-460 User’s Manual 7.3.2 Data Configuration t Mark b0, b1, b2, •••• Space (1) (2) (3) (1) Start Bit (2) Data Bit (+ Parity Bit) (3) Stop Bit (1 or More) (1) Start bit After a lapse of 1/2 bit from a mark-to-space fall edge, the state is read again, and if it is a space, it is recognized as the start bit. If it is a mark, it is assumed neither the start bit nor an error, and it is attempted to detect the start bit again.
iDP-460 User’s Manual 7.3.3 Error Detection A parity error, framing error, and overrun error are detected. When an error is detected, that data is either stored in the buffer as "?" or discarded. (Depends on DIP switch selection) The ERROR lamp is illuminated. (1) Framing error This error results when a space is detected in detecting the stop bit. That data is either stored in the buffer as "?" or discarded.
iDP-460 User’s Manual 7.3.
iDP-460 User’s Manual 8. DRAWER KICK-OUT CONNECTOR AND POWER CONNECTOR 8.1 Specifications of Drawer Kick-Out Connector (D-type Only) (1) Drawer kick-out drive signal The pulses specified by the BELL command(07h) are output.(Approx. 200 ms) (2) Electrical characteristics 1) Drive voltage: 24 V DC 2) Drive current: 0.8 A at maximum 8.1.1 Connector’s Pin Configuration No.
iDP-460 User’s Manual 8.2 Specifications of Power Supply Connector This is a power connector from an exclusive AC adapter. Connector’s Pin Configuration No. Function 1 2 +24V GND 1 Jack used 2 : HEC0470-01-640(HOSHIDEN) or equivalent Applicable plug : JXP series Type-A (I.D. 2.45 mm, O.D. 5.5 mm) (HOSHIDEN) or equivalent CAUTION: •Be sure to use the specified power supply. Use of unspecified one may lead to a trouble or breakage. •Do not connect the power supply with different polarities.
iDP-460 User’s Manual 9. MAINTENANCE AND SERVICE For the information on maintenance and service, please contact our dealer or at the following address. Northern America Other Areas CBM America Corporation Japan CBM Corporation Service Center Information Systems Division 365 Van Ness Way 1-1-7 Okubo Shinjuku-ku, Suit 510 Tokyo 169-8553 Japan Torrance, CA 90501, U.S.
iDP-460 User’s Manual 10. PRINT CONTROL FUNCTIONS 10.
iDP-460 User’s Manual 10.2 Command Sets A command set is set by a specific command. The available commands and functions differ depending on each setting. (1) P-250 command set There are two kinds of modes; P-200 mode and P-250 mode. with a P-900R mode and P-250 mode command. The P-900R mode are available The SI, SO, RS, US, and DC2 command operate differently between the P-200 mode and P-250 mode.
iDP-460 User’s Manual 10.3 Command Details 10.3.1 Description of Items XXXX ALL [Name] Command name [Code] A sequence of code constituting a command is represented in hexadecimal number for < >H, binary number for < >B, and decimal number for < >, respectively; [ ]k represents a repeat count of k-times. [Domain] Describes an argument value(setting range) for the command. [Function] Describes a command function. [Caution] Describes a caution as required.
iDP-460 User’s Manual 10-3-2 Details LF ALL [Name] Feed Paper [Code] <0A>H [Function] This command prints the data in the print buffer and feeds the paper by one line. If printing is completed, the command will shifts a printing position to the left margin and clear the print buffer. This is a standard command for printing one text line. [Caution] In other than the P-250 mode and P-900R mode, this command is ignored immediately after one-line buffer-full printing.
iDP-460 User’s Manual CAN ALL [Name] Clear Print Buffer and Cancel Character Attribute [Code] <18>H [Function] This command clears the contents of the print buffer without printing them and resets the character attribute and other attributes to Inactive or Default. [Caution] If the printer has started printing from the print buffer, this command will be ignored.
iDP-460 User’s Manual FS P-200,40ch [Name] Execute P-250 Mode [Code] <1C>H [Function] This command resets all the attributes, clears the print buffer, and set the right margin to 42. A subsequent command and printer operation will be of the P-250 mode. [Caution] If this command is received halfway printing, the data and attributes so far will be deleted. If this command is set in the P-250 mode, it will be ignored. [Initial Value] The P-200 mode is effectuated immediately after power-on.
iDP-460 User’s Manual RS ALL [Name] Set Double Width Character [Code] <1E>H [Function] This command prints its subsequent characters in double width. When there is only one character worth of position in a line, it will be printed in normal width. This attribute remains valid until the US command(normal width mode) or CAN command is received. In the P-200 mode, this attribute is reset to normal width at the beginning of each line, every time the line is fed.
iDP-460 User’s Manual [Function] 1. Serial interface 7-bit setting High pages are specified in all the modes. If this command is received, the character codes 20H to 7FH will be converted into A0H to FFH. This command remains valid until the SI command or CAN command is received. 2. Serial interface 8-bit setting and parallel interface This command is ignored in the P-250 mode and P-900R mode. In the other modes, it sets the double width characters(same as the RS command H).
iDP-460 User’s Manual BELL (D-type Only) ALL [Name] Drawer kickout [Code] <07>H [Function] This command outputs a designation signal to the connected drawer interface. The signal is about 200 ms. connected. Designation is made when the solenoid is The command functions even if not connected to the drawer interface, but it is meaningless. [Caution] Connect only what is specified to the drawer interface.
iDP-460 User’s Manual [Sample Program] When setting the line height to n = 20(1/3 inch) ESC a 20 ; → LPRINT CHR$(&H1B)+”a20;”; <1B>H<61>H<32>H<30>H<3B>H ESC b (n) ; ALL [Name] Eject Paper by n-lines [Code] <1B>H<62H>(n)<3B>H [Domain] 1 ≤ (n) ≤ 255 (<30>H ≤ n ≤ <39>H) [Function] This command ejects the paper by n-lines at the specified line height. [Caution] Be sure to add ";"(<3B>H) to the end of the parameter. If 0 or 256 or more is specified for the parameter, this command will be ignored.
iDP-460 User’s Manual ESC d P-250, P-900R [Name] Request Printer Status [Code] <1B>H<64>H [Function] In the P-250 mode and P-900R mode, this command sends the following 1-byte status messages shown below. This command is valid only for the serial interface.
iDP-460 User’s Manual [Caution] Be sure to add ";"(<3B>H) to the end of the parameter. This command is ignored in other than the P-250 mode and the P-900 mode. [Initial Value] The characters are printed after the LF command is received in the 42-columns mode.
iDP-460 User’s Manual [See Also] 11.2 International Character Codes List [Sample Program] When setting the character sets to Japan ESC h 8 ; → LPRINT CHR$(&H1B)+”h8;”; <1B>H<68>H<38>H<3B>H ESC I P-250, P-900R [Name] Identify Printer [Code] <1B>H<69>H [Function] This command sends a printer identification code by one byte. It sends "A"(<41>H) in the native mode and "H"<48>H) in the P-900R mode. [Caution] This command is invalid in the parallel mode, and P-200 mode.
iDP-460 User’s Manual 11. CHARACTER CODES TABLE 11.
iDP-460 User’s Manual 11.
iDP-460 User’s Manual 11.
iDP-460 User’s Manual APPENDIX 1. BLOCK DIAGRAM OSC16MHz Driver POWER LED ERROR LED FEED Switch DIP Switch Drawer Print Head Paper CPU End Driver Driver Interface Parallel (CENTRONICS) Serial (RS-232C ) DC Moter Driver Printer Mechanism Reset Vp AC Adapter 34 AD Series Filter Vcc Power Supply (26V DC, 1.
iDP-460 User’s Manual APPENDIX 2.
iDP-460 User’s Manual <<< German >>> 61 CITIZEN
iDP-460 User’s Manual 1. Bitte lesen Sie die Bedienungsanleitung vor dem Betrieb des Geräts aufmerksam durch und bewahren Sie die Anleitung anschließend für späteres Nachschlagen an einem sicheren Platz auf. 2. Änderungen des Inhalts dieser Anleitung bleiben ohne Vorankündigung vorbehalten. 3. Die Vervielfältigung dieser Bedienungsanleitung ohne vorherige Genehmigung verstößt, auch auszugsweise, gegen das Urheberschutzrecht. 4.
iDP-460 User’s Manual ZU BEACHTENDE SICHERHEITSMASSREGELN Zur Vermeidung von Gefahren gegenüber dem Bediener und anderen Personen und Sachschäden sind die folgenden Vorsichtsmaßregeln unbedingt zu beachten. • Der folgende Text beschreibt das Ausmaß der Gefahren und potentiellen Sachschäden, die durch eine Mißachtung der Bedienungshinweise oder durch die unsachgemäße Handhabung des Geräts entstehen können.
iDP-460 User’s Manual WARNUNG • Beim Betrieb des Geräts sind die nachfolgenden Vorsichtsmaßregeln unbedingt zu beachten. Eine Mißachtung dieser Hinweise kann zu Schäden, Funktionsstörungen, Rauchentwicklung und Brandgefahr durch Überhitzen und zu elektrischen Schlägen führen. Der fortgesetzte Betrieb des Geräts in anormalem Zustand, wie z.B. nach einer Beschädigung, kann Funktionsstörungen, Rauchentwicklung, fremde Gerüche/Geräusche und Brände verursachen.
iDP-460 User’s Manual VORSICHTSMASSREGELN FÜR DIE AUFSTELLUNG • Das Gerät nicht an Plätzen abstellen oder betreiben, an denen es Feuer, Feuchtigkeit oder direkter Sonnenbestrahlung ausgesetzt ist. Ebenso sind Plätze in der Nähe von Heizkörpern und sonstigen Wärmenquellen zu vermeiden, an denen Umgebungstemperatur und Luftfeuchtigkeit nicht den vorgeschriebenen Betriebsbedingungen entsprechen, sowie Plätze, an denen das Gerät Öl, Metallspänen oder Staub ausgesetzt ist.
iDP-460 User’s Manual VORSICHTSMASSREGELN FÜR DIE HANDHABUNG Zur Vermeidung von Problemen sind bei der Handhabung des Geräts die folgenden Vorsichtsmaßregeln zu beachten. • Für die Stromversorgung ausschließlich das vorgeschriebene Netzteil verwenden. • Den Druckbetrieb nicht ohne eingelegtes Papier oder ohne Farbband starten, da hierdurch der Druckkopf beschädigt werden kann. • Darauf achten, daß keine Fremdköper, wie z.B. Nadeln, Büroklammern oder Schrauben, in das Gehäuse gelangen.
iDP-460 User’s Manual TÄGLICHE WARTUNG • Vor der Wartung zuerst den Drucker ausschalten. • Schmutz und Staub mit einem trockenen, weichen Tuch vom Druckergehäuse abwischen. Bei starker Verschmutzung einen Lappen in Wasser anfeuchten, auswringen und damit abwischen. Hierzu niemals flüchtige organische Lösungsmittel, wie z.B. Alkohol, Terpentin, Trichlorethan, Benzol, Keton oder chemische Staubentfernungsmittel, verwenden. • Papierstaub mit einer weichen Bürste vom Gehäuse entfernen.
iDP-460 User’s Manual 4. BETRIEB 4.1 Anschluß des Netzteils 1. Den Netzschalter drücken. 2. Den Kabelstecker des Netzteils an die Netzanschlußbuchse an der Rückwand des Druckers anschließen. 3. Um Anschlußunterbrechungen vorzubeugen, den Kabelstecker, wie in der untenstehenden Abbildung gezeigt, mit Drahtklemmen sichern. 4. Den Netzstecker des Netzteils an eine Wandsteckdose anschließen. VORSICHT: • Ausschließlich das vorgeschriebene Netzteil verwenden.
iDP-460 User’s Manual 4.2 Anschluß des Schnittstellenkabels 1. Den Drucker (einschließlich angeschlossene Geräte) ausschalten. 2. Den Kabelstecker korrekt ausgerichtet (Ober- und Unterseite prüfen) an die Schnittstellenbuchse anschließen. 3. Die Kabelstecker befestigen: •Seriellschnittstelle: durch Festziehen der Schrauben sichern. •Parallelschnittstelle: durch Drehen des Anschlags sichern. •DIN-Minischnittstelle: bis zum Einrasten einschieben. 4. Das Kabel an einen Computer anschließen. 4.
iDP-460 User’s Manual 4.4 Einsetzen der Farbbandkassette 1. Die Druckerabdeckung aufklappen. 2. Bei schlaffem Farbband den Knopf in Pfeilrichtung drehen, um das Band vor dem Einsetzen der Kassette straff zu wickeln. 3. Die Farbbandkassette zwischen Druckkopfabdeckung und Walze einsetzen und gleichzeitig die Halteklauen in den Halter des Druckers drücken. 4. Das Farbband durch Drehen des Farbband-Kassettenknopfes in Pfeilrichtung straff wickeln. 5.
iDP-460 User’s Manual 4.5 Einlegen der Papierrolle 1. Mit den Fingern in die Aussparungen an beiden Seiten der Druckerabdeckung greifen, und die Abdeckung durch Anheben bis zum Anschlag öffnen. 2. Das Ende des Druckpapiers in nahezu rechtem Winkel abschneiden. VORSICHT: • Ausschließlich das vorgeschriebene Druckpapier verwenden. • Die Verwendung anderer Papiersorten kann zur Minderung der Druckqualität und zu reduzierter Betriebslebensdauer des Druckers führen.
iDP-460 User’s Manual VORSICHT: • Schlaffes Druckpapier durch Zurückdrehen der Papierrolle straffen. • Bei schräg eingesetztem Druckpapier den Papier-Freigabehebels drücken und das Papier gerade richten. • Die Druckerabdeckung niemals während des Druckens öffnen, da hierdurch Papierstaus entstehen können.
iDP-460 User’s Manual 4.6 Entfernen des restlichen Druckpapiers 1. Die Druckerabdeckung aufklappen. 2. Den Papier-Freigabehebel in Pfeilrichtung drücken und das Rollenpapier herausziehen. VORSICHT: Beim Herausziehen des Druckpapiers (in Vorwärts- oder Rückwärtsrichtung) darauf achten, den Papier-Freigabehebel zu betätigen. 4.7 Beseitigung von Papierstaus 1. Die Druckerabdeckung aufklappen. 2. Das Druckpapier vor der Papiereinzugöffnung sauber abschneiden. 3.
iDP-460 User’s Manual 4.8 Bedienfeld und Fehleranzeigelämpchen 1. Netzanzeigelämpchen (grün) (POWER) Leuchtet bei eingeschalteter Netzversorgung. 2. Fehleranzeigelämpchen (rot) (ERROR) Leuchtet, wenn das Papier aufgebraucht ist oder ein Fehler im Druckmechanismus oder in der Kommunikations auftritt.
iDP-460 User’s Manual 4.9 Druckvorgang Da der Druckkopf dieses Druckers nicht mit einem Temperatursensor (Thermistor) ausgestattet ist, wird er softwaremasig gegen Erhitzung geschutzt.
iDP-460 User’s Manual 5. EINSTELLUNG DER DIP-SCHALTER 5.1 DIP-Schalterstellung (1) Den Drucker ausschalten. (2) Das Farbband herausnehmen. Die DIP-Schalter sind wie in der Abbildung gezeigt angeordnet. (Bei der Paralllelschnittstelle ist nur DS1 vorhanden.
iDP-460 User’s Manual 1) DS1 Funktion ON OFF Werksseitige Einstellung Inland Ausland OFF Deaktiviert Aktiviert OFF 1 Zeichensatz 2 Automatische Ladefunktion 3 (Hinweis) -- -- OFF 4 (*1)Verwendetes Papier 1P 2P ON Funktion ON OFF Werksseitige Einstellung 1 Bitlänge 7 Bit 8 Bit ON 2 Parität Ja Nein ON 3 Parität Gleich Ungleich ON 4 Fehlerzustand Druckt "?" Ignoriert die Daten ON 5 Baudrate 6 Baudrate 7 Baudrate ON 8 Nicht verwende
iDP-460 User’s Manual 78 CITIZEN
