Instruction manual

C Calendar Mode
If you set Calendar for any of the 24 cities, Calendar
of all other cities will be automatically adjusted.
To adjust Calendar
(1) Press
M button to switch to Calendar mode.
(2) Press
A or B button to select a City for
adjustment.
(3) Press and hold
B button for more than 2
seconds. Month will flash.
(4) Press
A button to adjust Month. press and hold
A button for rapid advancement.
(5) Each time you press
B button, adjustment
section changes and start flashing as shown in the
diagram on the previous page.
(6) Press
A button to adjust flashing section.
(7) Press
B button again to return to normal
Calendar display.
 Year Setting
• Calendar can be set from 1996 through 2099
 Auto-Calendar function
• Month end adjustment will be made automatically.
• If Calendar is set to a non-existent date (e.g.,
February 30), display will automatically show first
day of next month.
 Auto-Return function
• If the watch is left in adjustment mode for more than
2 minutes without any buttons being operated, Auto-
Return will activate and return to normal Calendar
display.
 Instant Manual Return
• Instant Manual Return to normal Calendar display
can be made by pressing
M button in Calendar
adjustment mode.
D Alarm Mode
Setting Alarm
(1) Press
M button to switch
the watch to Alarm mode.
(2) Press
A or B button to
select City.
(3) Press and hold
B button
for more than 2 seconds. “ON”
or “OF” will flash. (When you press
B button at this
time, the name of the next City will appear for an
instant and then return to the City initially set.)
(4) “ON” and “OF” change each time
A button is
pressed.
(5) Press
B button. Hours will flash.
(6) Press
A button and adjust Hours.
• Press and hold
A
button for rapid advancement.
(7) Press
B
button again. Minutes will flash.
(8) Press
A
button and adjust Minutes.
(9) Finally press
B button to return to normal alarm
display.
 Alarm Buzzer
• Alarm will sound for 10 seconds.
• Press any button to stop alarm buzzer.
• To monitor Alarm buzzer, press
A button and hold
for more than 2 seconds when the watch is set to
normal alarm display. (Alarm sound will continue
while
A button is being pressed.)
 12/24-hour display
• If the watch is set to 12-hour display in Time mode,
Alarm will also be set to 12-hour display. Make sure
that AM/PM is correct when setting Alarm.
 Auto-Return function
• If the watch is left in alarm adjustment mode for
more than 2 minutes, it will automatically return to
normal alarm display.
• If the watch is kept in normal alarm display mode
for more than 2 minutes, it will automatically return to
normal alarm display.
 Instant Manual Return
• Press
M button in Alarm adjustment mode to return
to normal alarm display.
E Chronograph Mode
Chronograph measures
in units of 1/100 of a
second, up to 11 hours
59 minutes, 59 seconds
and 99 hundredths
seconds. After finishing
12-hour measurement, it
will return to reset state (all digits are zero) and stop.
you can also check split times while using
Chronograph.
Elapsed Time Measurement
(1) Press
A button to start/stop Chronograph.
(2) If
B button is pressed when Chronograph is
stopped, it will return to reset state.
• You will hear beep sound each time you press
A or
B button to start/stop or reset Chronograph.
(Different tones will sound for start and stop.)
Split Time Measurement
(1) Press
A button to start/stop Chronograph.
(2) Press
B button while Chronograph is running.
Split time will appear for 10 seconds.
• “SPLIT” will flash while split time is shown.
(3) Press
B button while measurement is stopped to
reset Chronograph.
• You will hear the beep sound each time you press
A or B button to start/stop or reset Chronograph
and to call up split time.