Setting Instructions for Movement Caliber 0850/0855 Contents 1) 2) 3) 4) 5) 6) 7) 8) (click on a topic) Outline Specifications Before Using Special Functions of the Solar Powered Watch Notes on Use Notes on Recharging Time Required for Recharging Using Your Watch a. Changing the mode b. Setting the Time c. Using the Alarm d. Using the Chronograph e. Insufficient Charge and Time Setting Warnings f.
Return to Table of Contents 1. Outline This is a multi-hand, multi-function analog solar and chronograph functions. A solar power function the power source for the watch hands movement and solar energy into electrical power with the solar powered watch with an alarm as its base, which provides alarm sound by converting cell, fitted on its face. 2.
Return to Table of Contents 3. BEFORE USING When the watch does not operate according to the handling instruction, it is insufficiently charged. Charge the secondary battery of the watch for more than 6 hours, approximately 20 cm away from the fluorescent lamp or incandescent lamp as light sources. When charging the secondary battery, do not pull it too close to the light source. * When charging the watch under direct rays of the sun, charge more than an hour.
Return to Table of Contents Insufficient Recharging Warning Function (Refer to section "Insufficient Charge and Time Setting Warnings") If the watch is put in the undercharged state during any display mode, it switches to the time display when in other display modes, then the second hand moves to the A CHARGE position, indicating the shortage of electricity. (Electric power shortage warning display) Even then, the time (hour, minute and 24-hour hands) runs accurately.
Return to Table of Contents 6. NOTES ON RECHARGE /!\ Caution * The watch will be damaged during recharging if it gets too hot (Over 60'C/140'F). o o Avoid recharging at high temperatures (Over 60 C/140 F). (eg)Charging the watch near a light source that easily become hot, such as an incandescent lamp or a halogen lamp. Charging in a place that easily becomes hot, such as a dashboard. 7. TIME REQUIRED FOR RECHARGE Time required for recharge may vary according to the design (color of the dial, etc.
Return to Table of Contents 8. HOW TO USE THIS WATCH 1) CHANGING THE MODE Other than the time display, this watch has alarm and chronograph main display functions- Each press of the (M) button changes Time -> Alarm -> Chronograph -> "O" position confirmation <(O)>. Confirm the change with the mode hand. After that returns to the time mode display. Display present time in hours, minutes, seconds and 24-hours. Use the 24-hour hand to confirm am/pm Not used usually.
2) TIME SETTING Return to Table of Contents Check that the mode hand is indicating and the watch is in time mode. 1) Pull the button (M) out, so that the second hand stops at the "O" position. Time setting synchronize the minute hand > hour hand -> 24-hour hand When the watch is adjusted by button operation, the time setting is completed by electro-magnetic correction. 2) Set the time by pressing button (B) or button (C) Each time button (B) is pressed ...............
Return to Table of Contents Depress button (B) or (C) continuously, the hands move rapidly. After setting the alarm time, push the (M) button. The hour, minute and 24hour hands move rapidly automatically to the present time. If those hands do not stop moving, push the (M) button again.
Return to Table of Contents Chronograph measurement Chronograph standard or accumulated elapsed time measurement. 1) Press button (M) to set the mode hand and get the chronograph display. At this time, the second hand and the function hand will return to the "O" position. The hour, minute, and 24-hour hands show the present time. 2) Each time button (A) is pressed, it repeatedly starts or stop the chronograph, along with a confirmation sound.
Return to Table of Contents 5) TIME SETTING AND RECHARGE WARNINGS When shown the insufficient charge warning display If the watch is put in the undercharged state during any display mode, it switches to the time display when in other display modes, then the second hand modes to the ^CHARGE position, indicating insufficiently charged. In such a case, expose the watch to sufficient light for the warning state to be cancelled.
Return to Table of Contents 6) CHECKING AND ADJUSTING EACH HAND'S "O" POSITION The watch's display may be incorrect due to the effect of static electricity, strong shock, etc. In such a case, check and adjust the "O" position of each of the following hands. “0” Position Checking Press button (M) to adjust the mode hand to zero (0) position. Then the watch is put in the '0' position check mode.
Return to Table of Contents PRECAUTIONS ABOUT CARE AND HANDLING OF WATCHES TEMPERATURE CARE Avoid temperature extremes. Exposing your watch to high temperatures, such as placing it on the dashboard of a vehicle or use in a hot tub, may cause the watch to malfunction, shorten battery life or damage certain components. Leaving the watch in extreme cold temperatures may cause irregular timekeeping until the watch returns to normal operating temperature.