User's Manual

ManualsBrandsCitizen ManualsPrinterCT-S4000DCL

4.6 Error Indication

The following LED indications are added to CT-S4000L/CT-S4000DCL.

LINE THERMAL PRINTER

MODEL CT-S4000L/CT-S4000DCL

User’s Manual

Contents

1.1 Features

4.6 Error Indications

5.3 Manual Setting of Memory Switch

5.4 Selecting Paper Type

5.5 Adjusting Paper Sensor

5.6 Printing Paper

1.1 Features

●High-speed printing at a maximum of 120 mm/sec

●2-dimensional barcode

●Label of nonstep 58 to 105 mm wide as well as 112 mm is usable

●Paper sensor sensitivity adjustment by variable resistor is adopted.

Status POWER LED ERROR LED Buzzer

Wait for cutting label OFF

Paper detection error OFF

Memory Switch Function 0 (OFF) 1 (ON)

SW4-4 Paper Select Thermal Roll BM.P/Lbl.P *

SW4-5 Position detect Black Mark Label

* The Print Width 660 dots is not available for printing a label paper.

* The memory switches SW2-8 will be ignored for Label.

5.3 Manual Setting of Memory Switch

Functions of memory switches SW4-4 and SW4-5 of CT-S4000L/CT-S4000DCL are as

shown below. (The white-on-black characters are factory setting.)

5.4 Selecting Paper Type

Paper type selection is available by the combination of memory switches SW4-4 and

SW4-5 by the used of “Memory Switch Select Mode”. In addtion, the following

procedure is available.

1 Enter Selecting Paper Type mode.

1)Open the printer cover and remove paper. Pressing and holding the FEED button,

turn the printer power ON. The POWER LED starts blinking.

2)Release the FEED button and then close the printer cover. Buzzer sounds and

the paper type currently set is indicated by the LED on the operation panel.

2 Select Paper Type.

Press the FEED button to match the paper type loaded to the LED indications in the

table below. (Refer to the table below.)

Refer to CT-S4000/CT-S4000DC User’s Manual of standard model when reading this manual.

Green lit (OFF)

(OFF) Red lit

Green lit Red lit

Label

Thermal paper roll

Black Mark paper

POWER LED ERROR LED

CITIZEN is a registered trade mark of Citizen Holdings Co., Japan

CITIZEN es una marca registrada de Citizen Holdings Co., Japón

Company names and product names in this manual are trademarks or

registered trademarks of relevant companies.

Summary of content (4 pages)

PAGE 1
4.6 Error Indication The following LED indications are added to CT-S4000L/CT-S4000DCL. LINE THERMAL PRINTER MODEL CT-S4000L/CT-S4000DCL User’s Manual Refer to CT-S4000/CT-S4000DC User’s Manual of standard model when reading this manual. Status POWER LED Wait for cutting label OFF Paper detection error OFF ERROR LED Buzzer 5.3 Manual Setting of Memory Switch Functions of memory switches SW4-4 and SW4-5 of CT-S4000L/CT-S4000DCL are as shown below. (The white-on-black characters are factory setting.
PAGE 2
3 Save the selected Paper Type to the Printer. Open and close the printer cover. By this operation, selected paper type is stored in the printer memory and the Selecting Paper Type mode is terminated. Since then, "P.Length Set" of Memory switch 4-1 becomes disable. When closing the printer cover during the setting a Black Mark paper or label paper in the printer, paper length is measured, and the result will be printed out.
PAGE 3
5.6 Printing Paper Also refer to the core dimension and notes of “5.2 Printing Paper” in User’s Manual of standard model. Use print paper shown in the following table or the equivalent.
PAGE 4
b) Black mark paper (BM paper) A B Cut position D C E Printable area F Paper feeding direction Black Mark (printed on the reverse) G Unit: mm Mark Item Dimensions A Right edge of black mark B Left edge of black mark 15 or more 0 to 1.5 C Black mark height 5 D Cut position in black mark 2.5 E Top margin F Black mark pitch 30 to 300 G Bottom margin 9 6.5 / 12 Top margin will be changed by the setting of the memory SW4-8. In the case of 0 (OFF), the top margin is 6.5mm.