European Union Directives Conformance Statement Hereby, CITIZEN WATCH CO., LTD., declares that this H15 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. You can view your product’s Declaration of Conformity (DoC) to Directive 1999/5/EC (the R&TTE Directive) at Citizen Watch global site: “http://www.citizenwatch-global.com/ ” “Service & Support” RF Exposure Information according to 2.1091/2.
FCC statements This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
Thank you for your purchase of this Citizen watch. Before using the watch, read this instruction manual carefully to ensure correct use. After reading the manual, store it in a safe place for future reference. Be sure to visit the Citizen website at http://www.citizenwatch-global.com/ . Here you will find a variety of information such as electronic setting guides, answers to frequently asked questions, Eco-Drive recharging information and more.
Safety precautions — IMPORTANT This manual contains instructions that should be strictly followed at all times not only for optimal use, but to prevent any injuries to yourself, other persons or property.
Before using this watch After unpacking, the following must be done before using the watch: • Checking the power reserve see page 16 For optimal performance, ensure your watch is fully charged prior to use. Refer to pages 10 to 15 for charging procedures and times.
Before using this watch Band adjustment We do not recommend attempting to adjust the watch band yourself. Special expertise and experience is required for proper adjustment. If not adjusted correctly, the band may become detached leading to an injury or loss of your watch. (Some retailers may supply a band adjustment tool with your purchase). For band adjustment, we recommend you consult the retailer where the watch was purchased or your nearest Authorized Citizen Service Center.
Before using this watch Screw down crown and screw down push button Unlock the crown prior to operate your watch. Unlock Lock Screw down crown Rotate the crown counterclockwise until it releases from the case. Push the crown in to the case. With gentle pressure towards the case, rotate the crown clockwise to secure it to the case. Be sure to tighten firmly. Screw down push button Rotate the locking screw counterclockwise, and loosen until it stops.
Table of contents Features ...................................8 Component identification .........9 Charging your watch .............. 10 Checking the current power reserve ................................ 16 Changing the mode................ 18 Before connecting to iPhone .. 24 Registering (Pairing) your iPhone [PR] ................ 35 6 Disconnecting with iPhone [DCT] ................................ 41 Connecting to the registered iPhone [CT]........................
Bluetooth 4.0 wireless technology .......................... 59 Adjusting the time and calendar manually [TME]/[CAL] .... 62 Using local time [L-TM] ........ 68 Using the chronograph [CHR]................................ 70 Checking and correcting the reference position [302] .... 72 Troubleshooting .................... 76 Resetting the watch — All Reset ........................ 81 Eco-Drive (solar powered) watch handling precautions........... 84 Water resistance ....................
Features Connectable with your iPhone using Bluetooth 4.0 through the dedicated app, and equipped with the following features: • Automatic Time Sync on page 47 • iPhone Search on page 51 • Incoming Call Alert on page 48 • Email Alert on page 52 • Schedule Alert on page 49 • Link Loss Alert on page 50 Eco-Drive (solar powered): Never needs a new battery. This watch is fueled by light. Chronograph: Measure elapsed time up to 60 minutes.
Component identification 1 5 Upper right button ( ) 2 6 3 Crown 7 4 Lower right button ( ) 8 The illustrations in this instruction manual may differ from the actual appearance of your watch.
Charging your watch This watch has a rechargeable cell which is charged by exposing the dial to light, such as direct sunlight or fluorescent lamps (refer to pages 12 and 13 for charging guidelines). After taking off the watch, put it in a location where the dial is exposed to bright light, such as by a window. For optimal performance, be sure to: • Expose the watch to direct sunlight half a day at least once a week. • Avoid leaving the watch in dark places for long periods of time.
Charging your watch When the watch reaches a low charge state (insufficient charge warning function) When the power reserve becomes low, the second hand moves once every two seconds. This is the insufficient charge warning function. Be sure to fully charge your watch as outlined on pages 12 and 13. • When the watch is sufficiently charged, the second hand will move normally.
Charging your watch Charging time by environment Below are the approximate times required for charging when exposing the watch dial to light continuously. Please use this table as a reference only.* Charging time (approx.) 12 Environment Illuminance (lx) To work for one day To start working To become fully normally when the cell charged when the cell is is discharged discharged Outdoors (sunny) 100,000 12 minutes 3.5 hours 13 hours Outdoors (cloudy) 10,000 30 minutes 6.
Charging your watch • To charge your watch, it is recommended to expose the dial to direct sunlight. Optimal charging is achieved by exposing the dial to direct sunlight outdoors for a short time each day.
Charging your watch Power save function If your watch is not exposed to light sufficient for charging for 30 minutes or more, the second hand will stop in order to conserve power. Although the second hand is not moving, the correct seconds are stored in memory. The power save function cannot be activated manually; it is an automatic feature only. The power save function does not operate under the following conditions: • The crown is in position or .
Charging your watch Canceling the power save function The power save function is automatically canceled when the watch is exposed to light sufficient for charging. The second hand will then resume normal movement. • The power save function will also be canceled if a notification is received from your iPhone. Note: the watch must be sufficiently charged and the dedicated app running on your iPhone in order to receive notifications.
Checking the current power reserve This watch has a power reserve display feature when in [TME], [L-TM], [PR], [CT], or [DCT] mode. Power reserve indication (Function hand on the upper right sub dial) Without iPhone connection With iPhone connection • If the current power reserve is not displayed (the watch is in [CAL] or [CHR] mode), change the mode (see page 18). • When connecting to iPhone, pay particular attention to the power reserve to ensure sufficient power is available.
Checking the current power reserve The power reserve level Level 3 2 1 With connecting to iPhone within 6 hours a day Up to 10 days Up to 15 days Up to 5 days Without connecting to iPhone Up to 3 months Up to 5 months Up to 2 months Approximate duration of Power reserve indication at is sufficient for this level all features and Power reserve is sufficient for all operations at this functions. Optimal level. performance is achieved at this level. * Power reserve is getting low.
Changing the mode This watch features eight different modes (functions). Change the mode by rotating the mode hand on the lower sub dial before using each mode. 1 Pull the crown out to position . The second hand moves to indicate the 30 seconds position. The second hand indicates the 30 seconds position.
Changing the mode 2 Rotate the crown to select a mode. • Each time you rotate the crown, the mode hand on the lower sub dial moves. Rotate the crown until the mode hand indicates the mode you wish to use. Proper location Improper location Ex. When selecting [L-TM] • You may turn the mode hand either clockwise or counterclockwise. • The hands/indications function differently in each mode. See pages 20 to 23 for more details of each mode and the functions of the hands/indications in each mode.
Changing the mode Mode indications and functions 24-hour hand Function hand Time — [TME] • Normally, use the watch in [TME] or [L-TM] mode. [TME] The currently set time is displayed. • The function hand on the upper right sub dial indicates the power reserve in this mode.
Changing the mode Pairing/Connecting/Disconnecting of iPhone — [PR]/[CT]/[DCT] [PR] (Pairing) [CT] (Connect) [DCT] (Disconnect) Select this when you want to connect (pair/register) the watch to your iPhone for the first time. (See page 35.) Select this mode when you want to connect your watch to your iPhone after initial pairing. (See page 44.) Select this when you disconnect the watch from your iPhone. (See page 41.) • Time indication is same as either [TME] or [L-TM].
Changing the mode Local time — [L-TM] [L-TM] Select this to display the time of another area (local time). (See page 68.) • The 24-hour hand on the upper left sub dial, date and day of the week display local time. • The function hand on the upper right sub dial indicates the power reserve in this mode. 22 Chronograph — [CHR] [CHR] Select this when you want to use the chronograph. (See page 70.) • The second hand: Indicates the chronograph seconds.
Changing the mode Calendar — [CAL] The reference position — [302] [CAL] [302] Select this to display the calendar. (See page 64.) • The second hand: Indicates the year/month. • The function hand on the upper right sub dial: Indicates the day of the week. • The hour, minute and 24-hour hands will continue to reflect the current time set in [TME] mode. The current reference position of each hand/indication is indicated. (See page 72.
Before connecting to iPhone This watch communicates with iPhone through the connection of Bluetooth 4.0, which is featured Bluetooth Low Energy (BLE) power-saving technology. It is required for connection to install and start up a dedicated app “CITIZEN ECO-DRIVE Proximity” on a compatible iPhone. The flow for connection is shown as follows. • Screen in this manual may differ from the actual app.
Before connecting to iPhone iPhone connectable with this watch To check the latest information on compatible iPhone and iOS, visit the following sites: • Citizen Watch global site: “http://www.citizenwatch-global.com/ ” “Service & Support” Set the mode to [DCT] (see page 42) to use this watch as a standard one in places such as an airplane, where electronic devices are limited to use. iPhone is a trademark of Apple Inc., registered in the U.S. and other countries.
Before connecting to iPhone Functions available with the connection Automatic adjustment of time and calendar [Time Sync] The watch adjusts time and calendar automatically using time info provided from the iPhone. Time info ACT Cellular phone network 26 The second hand points “ACT” while receiving time info from iPhone.
Before connecting to iPhone Incoming call notification [Incoming Call] Incoming call alert comes to the watch since iPhone’s call reception. CALL Incoming Call Incoming call info Cellular phone network The watch vibrates twice and the second hand points “CALL” as it receives incoming call info.
Before connecting to iPhone Schedule notification [Schedule Alert] The watch receives schedule notification from the built-in Calendar app on your iPhone, corresponding to the setting of the app. MAIL Schedule notification Schedule notification info The watch vibrates twice and the second hand points “MAIL” as it receives notification info.
Before connecting to iPhone Email reception notification [Email Alert] Email alert comes to the watch since iPhone’s email reception to the account set on the dedicated app. MAIL Email notification Cellular phone network Email notification info The watch vibrates twice and the second hand points “MAIL” as it receives notification info.
Before connecting to iPhone Link Loss alart (Bluetooth disconnection notification) [Bluetooth Link Loss Alert] The watch notifies iPhone’s disconnection due to their distance. Bluetooth connectable range 5 m (16-1/2 feet) to 10 m (33 feet) LL The watch vibrates twice and the second hand points “LL” as it detects disconnection.
Before connecting to iPhone iPhone search [iPhone Search] The watch sends signals to the registered iPhone within the connectable range. • This function is also available when they are disconnected. Bluetooth connectable range 5 m (16-1/2 feet) to 10 m (33 feet) ACT The iPhone sounds (depending on the setting) as it receives the signal. The second hand points “ACT” as it starts to send signals.
Before connecting to iPhone Connection and notification indication on the watch • Because the watch vibrates gently for the notification, it is recommended to check the vibration in advance. (See page 34.
Before connecting to iPhone • The maximum connectable range is about 10 m (33 feet). Connectable range may be shorter due to obstacles such as walls. Do not block the watch with your body such as your arm. • When [▶0◀], [CHR] or [CAL] mode is selected, only vibration gives you notification. The indication by the second hand will be made with another vibration when you change the mode to [TME], [L-TM], [PR] or [CT]. You can check how the watch vibrates in advance. (See page 34.
Before connecting to iPhone Testing the vibration of the watch 1 Change the mode to [CT]. (See pages 18 and 19) 2 Pull the crown out to position . 3 Press and release either the lower right button or upper right button . The watch starts vibrating. • The vibration is different from the actual notification vibration. 4 Push the crown in to position . 5 Change the mode to either [TME] (or [L-TM]) to finish the procedure.
Registering (Pairing) your iPhone [PR] When connecting the watch and your iPhone for the first time, mutual registration (pairing) is required. Before registration • For registration, you have to operate both the watch and the iPhone. • Be sure that the watch and the iPhone are charged enough. Especially, check the power reserve indication of the watch (see page 16) and charge it before registration if the power reserve level is “1” or “0”. • The watch and the iPhone is connected after registration.
Registering (Pairing) your iPhone [PR] Connection after registration Once the registration has been completed, re-registration (pairing) is not required except for the cases below. Execute reconnection (see page 44) when disconnected. • After registering with another iPhone • After uninstalling the dedicated app from the iPhone • After restoring iPhone to the factory setting Registering the iPhone The iPhone registration on the watch must be completed within about 2 minutes.
Registering (Pairing) your iPhone [PR] 1 Download and install the dedicated app “CITIZEN ECO-DRIVE Proximity” from App Store. 2 Tap the app icon to start up the app. 3 Slide the switch of “Scan” to “ON” on the app’s screen. Scan ON The iPhone starts to detect the watch. • Do not change the app screen until the registration is completed. • When “Waiting for Reconnection” is shown, slide the switch to “OFF”.
Registering (Pairing) your iPhone [PR] 4 Pull the crown out to position . The second hand moves to indicate the 30 seconds position. 5 Rotate the crown to change the mode to [PR]. 6 Push the crown in to position . The second hand moves to indicate the “ACT” position, allowing the watch to be detected for two minutes. • The last register information will delete in this step.
Registering (Pairing) your iPhone [PR] 7 Tap “Pair” when the permission request of Bluetooth connection appears on the app’s screen. Registration completes successfully when “Proximity Connect” appears on the screen. Proximity Connect ON • It may take up 20 to 30 seconds to complete the registration.
Registering (Pairing) your iPhone [PR] The function hand on the upper right sub dial points the area shown on the right (“ON” area) when registration completes successfully and the watch is connected with the iPhone. “ACT” indication ends and the second hand returns to second indication. 8 Change the mode to either [TME] (or [L-TM]) to finish the procedure.
Disconnecting with iPhone [DCT] You can close the connection with the iPhone in the following cases: • When the function hand on the upper right sub dial indicates “ON” area. • When the watch mode is set to [TME], [L-TM], [PR] or [CT]. • When the second hand indicates the second. (While the second hand indicates a notification type, stop the notification indication by pressing and holding either the lower right button or upper right button for two seconds.
Disconnecting with iPhone [DCT] You can also close connection by changing the mode of the watch. 1 Change the mode to [DCT]. (See pages 18 and 19) The connection is closed and the function hand on the upper right sub dial indicates “OFF” area. • In this case, the switch name changes from “Proximity Connect” to “Waiting Function hand for Reconnection”. Waiting for Reconnection ON on the upper right sub dial 2 Change the mode to either [TME] (or [L-TM]) to finish the procedure.
Disconnecting with iPhone [DCT] Checking the connection status on the app screen While connected Disconnected Proximity Connect ON Only the following operations are available: • Reconnection with the operation on Shown when the disconnection the watch (see page 44) is done by the watch operation or intentionally. In this case, you cannot • Searching for your iPhone (see page 51) register the iPhone. Waiting for Reconnection ON Scan ON Shown when the disconnection is done by the app operation.
Connecting to the registered iPhone [CT] You can reconnect with the registered iPhone again in the following cases: • When the function hand on the upper right sub dial indicates “OFF” area. • When the watch mode is set to [TME], [L-TM], [PR] or [CT]. • When the second hand indicates the second. (While the second hand indicates a notification type, stop the notification indication by pressing and holding either the lower right button or upper right button for two seconds.
Connecting to the registered iPhone [CT] You can also reconnect the watch and the iPhone by changing the mode of the watch. 1 Change the mode to [CT]. (See pages 18 and 19) The second hand moves to indicate “ACT”. When successfully connected, the movement of the second hand returns to normal and the function hand on the upper right sub dial indicates “ON” area. Function hand • It may take up 20 to 30 seconds to on the upper complete the reconnection.
Activating the functions of the dedicated app You can set functions to “ON” or “OFF” on the app’s screen during connection. For the details of each function, refer to the pages shown below. Function Time Sync Incoming Call Schedule Alert Email Alert Bluetooth Link Loss Alert iPhone Search 46 Page Description 47 Sends time/calendar info. 48 Sends notification of incoming call. 49 Sends notification of schedule from the built-in Calendar app on the iPhone.
Activating the functions of the dedicated app Automatic adjustment of time and calendar [Time sync] When you set “Time Sync” to “ON”, the watch receives the time info (year, month, date, day, hour, minute, second) from the iPhone and adjust the time following it each time they are connected. Time Sync ON • The time on the watch is adjusted automatically each time they are connected and the time setting of your iPhone is changed during connection.
Activating the functions of the dedicated app Receiving incoming call notification [Incoming Call] When you set “Incoming Call” to “ON”, the watch receives incoming call info from the iPhone connected. Incoming Call ON When receiving incoming call info The watch vibrates twice and the second hand points “CALL”. • To return the second hand to normal movement, press and hold either the lower right button or upper right button for two seconds.
Activating the functions of the dedicated app Receiving schedule notification [Schedule Alert] When you set “Schedule Alert” to “ON”, the watch receives schedule notification from the iPhone connected. Schedule Alert ON • For schedule alert setting, set it on the alert setting of the iPhone’s Calendar. When receiving schedule notification The watch vibrates twice and the second hand points “MAIL”.
Activating the functions of the dedicated app Receiving the leaving-iPhone alert (Bluetooth disconnection notification) [Bluetooth Link Loss Alert] When you set “Bluetooth Link Loss Alert” to “ON”, the watch alerts when the communication with the iPhone is closed due to the iPhone location or other unintentional reasons. Bluetooth Link Loss Alert ON • No notification is sent to the watch if the iPhone and other Bluetooth devices are disconnected.
Activating the functions of the dedicated app Searching for the iPhone [iPhone Search] When you set “iPhone Search” to “ON”, you can send signals to the registered iPhone in the connectable range with the watch. When receiving the signal, the iPhone sounds depending on its setting.
Receiving email reception notification [Email Alert] When you set “Email Alert” to “ON”, the watch receives email notification at email arrival to the account set on the dedicated app “CITIZEN ECO-DRIVE Proximity”. Email Alert ON • You can enter up to five mail accounts. • This function does not notify the receptions of iPhone’s Mail and SMS. • This app only check existence of new unread mails on mail servers. You cannot browse mails on it.
Receiving email reception notification [Email Alert] Setting the mail account To send the mail reception info to the watch, you have to set mail accounts on the dedicated app. • This function is only available for accounts whose mail servers are compatible with IMAP. • Prepare IMAP mail account, IMAP mail server addresses for sending and receiving, user name and password before setting. Consult your mail service provider for the information required. • You can set the mail accounts before connection.
Receiving email reception notification [Email Alert] 2 Tap “+” to add an account. Back Mail Accounts • Tap an existing account to edit its setting. 3 Select an IMAP mail service you use on the list and tap its name. • If your mail service is not listed, tap “Other”. 4 Enter items required and tap “Done”. Cancel IMAP Setting Done Connection test to the mail server starts immediately and the mail account entered is verified. When the test ends successfully, the screen of step 2 appears again.
Receiving email reception notification [Email Alert] 5 Repeat steps 2 to 4 to set other accounts. • The accounts set are listed under “Email Alert”. Email Alert ON Account 1 ON Account 2 ON 6 Tap “Back” to finish the setting. To delete an existing mail account from the app Tap “Delete Account” on the screen of an existing account. • All the settings are deleted as the dedicate app is uninstalled on the iPhone.
Receiving email reception notification [Email Alert] Selecting accounts for which mail reception notification is sent You can select accounts for mail reception notification by setting them to “ON” or “OFF”. 1 Tap the app icon to start up the app. 2 Slide the switch for each account under “Email Alert” to “ON” or “OFF”.
Receiving email reception notification [Email Alert] Adjusting the interval of mail reception notification You can adjust the interval of mail reception notification. • The interval set is common to all mail accounts. 1 Tap the app icon to start up the app and tap “Mail Accounts”. 2 Tap “Polling Interval”. Polling Interval 3 Tap the interval you prefer. • Increased use of this feature may affect battery life.
Shortcut for registration (pairing) The registration (see page 35) can also be performed by the simple operation below. • Make sure the watch is sufficiently charged before registration. (See pages 16 and 17.) Registration [PR] When the function hand on the upper right sub dial indicates “OFF”, press and hold the upper right button for seven seconds or more. • You can operate the buttons while the mode is set to [TME], [L-TM], [PR] or [CT], and the second hand indicates the second.
Bluetooth 4.0 wireless technology Bluetooth is a type of wireless communication technology used over distances of about 5 m (16-1/2 feet) to 10 m (33 feet) from handheld information products such as smartphones, head sets and game gadgets. • This watch supports the Bluetooth 4.0 utilizing the electricity saving technology, Bluetooth 4.0 (Bluetooth Low Energy). • The communication distance using Bluetooth may become smaller when obstacles such as walls exist.
Bluetooth 4.0 wireless technology Within the frequency band (2.4 GHz) used by this watch, local area wireless stations (wireless stations requiring a license) for identifying the mobile objects used on the production lines of factories, etc. in addition to industrial, scientific and medical applications such as microwaves, specific low electric power wireless stations (wireless stations not requiring a license), and amateur radio stations (wireless stations requiring a license) are operated.
Bluetooth 4.0 wireless technology • The connectable distance for the Bluetooth 4.0 is approximately 10 m (33 feet) in an ideal location. Placing the transmitter and receiver behind reinforced concrete or metallic walls may block radio waves and disrupt sufficient communication. The communication distance may shorten depending on the environment where this watch is used.
Adjusting the time and calendar manually [TME]/[CAL] Adjusting the time — [TME] 1 Change the mode to [TME]. (See pages 18 and 19) 2 Pull the crown out to position . The second hand rotates to indicate the current time. 3 Press and release the lower right button upper right button or . The second hand moves to indicate the 0 seconds position.
Adjusting the time and calendar manually [TME]/[CAL] 4 Rotate the crown to adjust the time. • You can adjust the time in one minute increments. • The hour and minute hands and 24-hour hand on the upper left sub dial move in conjunction with one another. • When adjusting the time, be sure to pay particular attention to the 24-hour hand to ensure AM or PM time is set properly. • If you spin the crown quickly a few times, the hand will move continuously.
Adjusting the time and calendar manually [TME]/[CAL] Adjusting the Calendar — [CAL] • The hour and minute hands and 24-hour hand on the upper left sub dial will indicate the time set in [TME] mode. • While in [CAL] mode, notifications will be through watch vibration only. Visual notification by the second hand occurs only in [TME], [L-TM], [PR] or [CT] mode. 1 Change the mode to [CAL]. (See pages 18 and 19) 2 Pull the crown out to position .
Adjusting the time and calendar manually [TME]/[CAL] 4 Press and release the upper right button . The function hand on the upper right sub dial will move slightly to indicate that the date can be set. 5 Rotate the crown to adjust the date. • Each time you rotate the crown fully clockwise, the function hand on the upper right sub dial will rotate five times and the date will advance by one day. When you rotate the crown fully counterclockwise, it will go back by one day.
Adjusting the time and calendar manually [TME]/[CAL] 8 Change the mode to [TME] (or [L-TM]) to finish the procedure. (See pages 18 and 19) • The date will change at approximately 0:00 a.m. (midnight). This process takes approximately 5 seconds to complete. Month and year indications The month and leap year are indicated by the position of the second hand when in [CAL] mode. When set correctly, the watch will be automatically adjusted for months shorter than 31 days as well as for leap years.
Adjusting the time and calendar manually [TME]/[CAL] Each minute mark denotes the number of years since the last leap year. Leap year 1st year since leap year 2nd year since leap year 3rd year since leap year In the example above, the second hand indicates April and 2 years since the last leap year. Quick reference chart for number of years passed since leap year Indication of the second hand Hour marker Leap Year/Years since leap year Leap year Actual year 2012, 2016, 2020 1st min.
Using local time [L-TM] Indicating local time (secondary time) The watch can indicate the time of another time zone (known as local time) using [L-TM] mode. 1 Change the mode to [L-TM]. (See pages 18 and 19) The currently set local time (secondary time) is displayed. • The hour, minute, 24-hour, date and day of week are displayed. • If a local time (secondary time) has not been set, the time reflected will be that of the time set in [TME] mode.
Using local time [L-TM] Setting the local time The setting range of the time difference from the time set in [TME] mode is ±27 hours in 15-minute increments. 1 Change the mode to [L-TM]. (See pages 18 and 19) 2 Pull the crown out to position . 3 Rotate the crown to set the time in 15-minute increments. • When you rotate the crown quickly a few times, the hands will move continuously. To stop the rapid movement, rotate the crown in either direction. 4 Push the crown in to position to finish the procedure.
Using the chronograph [CHR] The 60-minute chronograph can indicate a maximum of 59’ 59”. • While in [CHR] mode, notifications will be through watch vibration only. Visual notification by the second hand is disabled in this mode and will be made with another vibration when you change the mode to [TME], [L-TM], [PR] or [CT]. 1 Change the mode to [CHR]. (See pages 18 and 19) The second hand moves to indicate the 0 seconds position to enable you to measure time. 2 Use the chronograph.
Using the chronograph [CHR] Upper right button Start/Stop/Restart measurement. Second hand: This indicates the elapsed seconds while using the chronograph. : The chronograph minute hand: This indicates the elapsed minutes (up to 60) while using the chronograph. Lower right button : Reset • Press and release this button to reset the chronograph after timing. • After one hour of continuous chronograph operation, the chronograph automatically stops and is reset.
Checking and correcting the reference position [302] If the time or date is not shown correctly even after proper reception of the time info, check whether the reference position is correct. 72 Correct reference positions What is the reference position? The base position of all hands and date to properly indicate the various functions of this watch.
Checking and correcting the reference position [302] Checking the reference position Check whether the reference position of each hand and indication is accurate. 1 Change the mode to [302]. (See pages 18 and 19) The hands and date will rotate to the current reference positions stored in memory. 2 Check the current reference position. By referring to the chart on page 72, ensure the reference position of each hand and the date are correct. • If all reference positions are correct, go to step 3 below.
Checking and correcting the reference position [302] Correct the current reference position Correct each hand and indication to indicate the correct reference position. 1 Change the mode to [302]. (See pages 18 and 19) Each hand and indication indicate the current reference position. 2 Pull the crown out to position . This will enable you to correct the reference position. 3 Press and release the upper right button .
Checking and correcting the reference position [302] 4 Rotate the crown to correct the reference position of the active hand/ indication. • When you rotate the crown quickly a few times, the hands and indications will move continuously. The second hand will move one full rotation, and the other hands and indications will move until you rotate the crown either clockwise or counterclockwise. 5 Repeat steps 3 and 4 as required. 6 Push the crown in to position .
Troubleshooting If you have a problem with your watch, check the table below. Symptoms Remedies Page Connection with iPhone Check the power reserve. Connection is unsuccessful • If you cannot solve your problem with the remedies shown on the right, consult the nearest Authorized Citizen Service Center. Check the mode of the watch. Press and hold either the lower right button or upper right button for two seconds to cancel the notification indication.
Troubleshooting Symptoms Remedies Check the connection status (“ON”, “OFF”). Check the power reserve. Not notified within connectable distance Ensure your iPhone is not being obscured such as by being in a pocket or purse. When in [302], [CHR] or [CAL] mode, notification of iPhone is through vibration only. The visual indication by the second hand is available only in [TME], [L-TM], [PR] or [CT] mode. Turn “ON” of the functions on the app’s screen.
Troubleshooting Symptoms Remedies Page Check if your iPhone is in communication distance (5 m / 16-1/2 feet to 10 m / 33 feet) and avoid obstacles between the watch and the iPhone. − Check the connection status (“ON”, “OFF”). 32 Connection with iPhone (continued) Time info cannot be obtained automatically. iPhone does not sound using iPhone Search. Check if the watch is ready to receive the time info (the mode is set to [TME], [L-TM], [PR] or [CT] and the crown is in position ).
Troubleshooting Symptoms Remedies This may occur as a result of a pairing (registration) or connection failure. Pull the crown out to The second hand remains position or , then push it in to position . If this does not work, leave the watch for about two indicating “ACT” and does not move at all. or more minutes. If the second hand still does not move, consult the nearest Authorized Citizen Service Center.
Troubleshooting Symptoms Remedies The second hand does not move. Check the current mode. The second hand does not move in some modes. Press and release either the lower right button or upper right button to cancel the notification indication. The second hand moves once every two seconds. This indicates low power. Fully charge the watch. Page 18 to 23 − 10 to 15 The time and/or date is incorrect. Change the mode to [TME]. The indication of the time and date is incorrect.
Troubleshooting Resetting the watch — All Reset When the watch hands move in an unusual manner (e.g. the hand does not stop moving, or the watch does not operate even though it has been recharged) due to strong shock or static, etc., we recommend resetting the watch (All Reset).
Troubleshooting Be sure to perform the following operations after All Reset. 1. Correct the reference position. After performing the All Reset feature, the watch is in the reference position mode. Refer to the reference position setting procedure outlined on page 74, starting from step 3. 2. Adjust the time and calendar (after correcting the reference position). • When adjusting using iPhone: Connect a iPhone (see page 44), then obtain the time info (see page 47). See pages 62 to 67.
Troubleshooting Make sure the watch is fully charged as outlined on pages 10 to 13 before proceeding. 1 Pull the crown out to position . The second hand moves to indicate the 30 seconds position. 2 Rotate the crown to change the mode to [302]. All hands and identifications other than the second hand will indicate the current reference position stored in memory. Do not operate the watch until all hands/indications stop moving. 3 Pull the crown out to position .
Eco-Drive (solar powered) watch handling precautions • Please note that if you wear long sleeves, the watch may stop as a result of being covered by your sleeve and blocked from the light. • When you take off the watch, try to place it in as bright a location as possible. This will ensure optimal operation.
Eco-Drive (solar-powered) watch handling precautions CAUTION Recharging Precautions • Do not charge the watch at a high temperature (about 60°C (140°F) or higher) as doing so may cause the movement to malfunction. Examples: • Charging the watch too close to a light source which generates a large amount of heat such as an incandescent lamp or halogen lamp.
Eco-Drive (solar-powered) watch handling precautions • This watch utilizes a special rechargeable cell that does not require regular replacement. However power consumption may increase after using the watch for a number of years due to wear of internal components and deterioration of oils. This may cause stored power to be depleted at a faster rate.
Eco-Drive (solar-powered) watch handling precautions WARNING Use Only the Specified Battery • Never use a battery other than the rechargeable cell specified for use in this watch. Although the watch structure is designed so that it will not operate when another type of battery is installed, if a silver battery or other type of battery is installed in the watch and the watch is recharged, there is the risk of overcharging which may cause the battery to rupture.
Water resistance WARNING Water Resistance • Refer to the watch dial and the case back for the indication of the water resistance of your watch. The following chart provides examples of use for reference to ensure that your watch is used properly. (The unit “1bar” is roughly equal to 1 atmosphere.) • WATER RESIST(ANT) ××bar may also be indicated as W.R.××bar.
Water resistance Water-related use Minor exposure to water (washing face, rain, etc.
Water resistance • Non-water resistant models are not designed to come into contact with any moisture. Take care not to expose a watch with this rating to any type of moisture. • Water resistance for daily use (to 3 atmospheres) means the watch is water resistant for occasional accidental splashing. • Upgraded water-resistance for daily use (to 5 atmospheres) means that the watch may be worn while swimming, but is not to worn while skin diving.
Precautionary items and usage limitations CAUTION To Avoid Injury • Be particularly careful when wearing your watch while holding a small child, to avoid injury. • Be particularly careful when engaged in strenuous exercise or work, to avoid injury to yourself and others. • Do NOT wear your watch while in a sauna or other location where your watch may become excessively hot, since there is the risk of burns.
Precautionary items and usage limitations CAUTION Precautions (continued) • Even if your watch has a high level of water resistance, please be careful of the following. • If your watch is immersed in sea water, rinse thoroughly with fresh water and wipe with a dry cloth. • Do not pour water from a tap directly onto your watch. • Take off your watch before taking a bath. • If seawater enters the watch, place the watch in a box or plastic bag and immediately take it in for repair.
Precautionary items and usage limitations • The rubber (urethane) band may be stained by dyes or soil present in or on clothing or other accessories. Since these stains may not be removable, caution is required when wearing your watch with items that tend to easily transfer color (articles of clothing, purses, etc.). In addition, the band may be deteriorated by solvents or moisture in the air. Replace with a new one when it has lost elasticity or become cracked.
Precautionary items and usage limitations • Analog quartz watches are powered by a step motor that uses a magnet. Subjecting the watch to strong magnetism from the outside can cause the motor to operate improperly and prevent the watch from keeping time accurately. Do not allow the watch to come into close proximity to magnetic health devices (magnetic necklaces, magnetic elastic bands, etc.
Precautionary items and usage limitations • Be sure to remove any protective stickers that may be on your watch (case back, band, clasp, etc.). Otherwise, perspiration or moisture may enter the gaps between the protective stickers and the parts, which may result in a skin rash and/or corrosion of the metal parts.
Precautionary items and usage limitations Caring for Your Watch • Wipe any dirt or moisture such as perspiration from the case and crystal with a soft cloth. • For a metallic, plastic or rubber (urethane) watchband, wash any dirt off with water. Remove the small amounts of dirt trapped between the crevices of the metallic band with a soft brush. • For a leather band, wipe off dirt using a dry cloth.
Information About Bluetooth Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. Some countries may prohibit the usage of the Bluetooth. See page 59.
Specifications Model W760 Timekeeping accuracy (without reception) Within ±15 seconds per month when worn at normal operation temperatures between +5˚C (41°F) and +35˚C (95°F) Operating temperature range –10˚C (14°F) to +60˚C (140°F) Display functions • Time: Hours, minutes, seconds, 24-hour • Calendar: Date, day of the week Type Analog solar-powered watch Maximum run time from full • Fully charged to fully discharged (when power save feature works about 7.
Specifications Additional functions • • • • • • Solar power function Power reserve indication (in four levels) Overcharging prevention function Insufficient charge warning function (two-second interval movement) Energy saving function (power save feature) Indications relative to iPhone Connection status indication (ON/OFF) Indication of ongoing communication processing (ACT) Notification indication (CALL/INFO/LL) • Chronograph (up to 60 minutes in one second increments) • Local time • Perpetual calendar (
