Instruction manual
Instruction manual: CITIZEN Eco-Drive Proximity
abc
5
Before connecting to iPhone (continued)
Connection and notification indication on the watch
• Because the watch vibrates gently for the notification, it is
recommended to check the vibration in advance. (See page
5a
.)
Connection status (the
function hand on the
upper right sub dial)
ON
Connected
OFF
Not
connected.
• Since the actual
pointing position
of the hand varies
depending on the
amount of charge,
distinguish “
ON
”
and “
OFF
” by
the area the hand
points.
Notification position of the
second hand
CALL
Incoming phone
calls
MAIL
Emails and
schedule info
LL
Disconnection
(Link Loss)
ACT
The watch is
waiting to be
connected or
processing
communication
(Activation)
• The maximum connectable range is about 10 m (33feet).
Connectable range may be shorter due to obstacles such as walls.
Do not block the watch with your body such as your arm.
• When [▶
0
◀], [
CHR
] or [
CAL
] mode is selected, only vibration gives
you notification. The indication by the second hand will be made
with another vibration when you change the mode to [
TME
], [
L-TM
],
[
PR
] or [
CT
].
You can check how the watch vibrates in advance. (See page
5a
.)
• When the watch receives a new info while the second hand indicates
a notification type, the hand’s indication is updated corresponding to
the new info.
Stopping the notification indication
Press and hold either the lower right button or upper right button
for two seconds while the second hand indicates a notification, and the
second hand stops the notification indication and return to the normal
movement.
Testing the vibration of the watch
1
Change the mode to [
CT
].
(See page
3b
.)
2
Pull the crown out to position .
3
Press and release either the lower right button
or upper right button
.
The watch starts vibrating.
• The vibration is different from the actual
notification vibration.
4
Push the crown in to position .
5
Change the mode to either [
TME
] (or [
L-TM
]) to
finish the procedure.
(See page
3b
.)
Registering (Pairing) your iPhone [
PR
]
When connecting the watch and your iPhone for the first time, mutual
registration (pairing) is required.
Before registration
• For registration, you have to operate both the watch and the iPhone.
• Be sure that the watch and the iPhone are charged enough.
Especially, check the power reserve indication of the watch (see page
3a
) and charge it before registration if the power reserve level is “1”
or “0”.
• The watch and the iPhone is connected after registration.
Connection after registration
Once the registration has been completed, re-registration (pairing)
is not required except for the cases below. Execute reconnection (see
page
6b
) when disconnected.
• After registering with another iPhone
• After uninstalling the dedicated app from the iPhone
• After restoring iPhone to the factory setting
Registering the iPhone
The iPhone registration on the watch must be completed within
about 2 minutes. If about 2 minutes have passed before
finishing the registration, the watch returns to the normal
movement.
• The installed app is shown as the icon.
• After registration, set the functions to “
ON
” on the app’s
screen on the iPhone. (See page
6c
.
)
<Operation on iPhone>
1
Download and install the dedicated app “CITIZEN
ECO-DRIVE Proximity” from App Store.
2
Tap the app icon to start up the app.
3
Slide the switch of “Scan” to “ON” on the app’s
screen.
The iPhone starts to detect the watch.
• Do not change the app screen until the registration
is completed.
•
When “
Waiting for Reconnection
” is shown, slide
the switch to “
OFF
”.
•
When the iPhone’s Bluetooth setting is “
OFF
”, a n
activation dialog appears.
App icon
Scan
ON
<Operation on the watch>
4
Pull the crown out to position .
The second hand moves to indicate the 30 seconds
position.
5
Rotate the crown to change the mode to [
PR
].
6
Push the crown in to position .
The second hand moves to
indicate the “
ACT
” position,
allowing the watch to be
detected for two minutes.
• The last register information
will delete in this step.
<Operation on iPhone>
7
Tap “Pair” when the permission request of
Bluetooth connection appears on the app’s screen.
Registration completes successfully when
“
Proximity Connect
” appears on the screen.
• It may take up 20 to 30 seconds to complete the
registration.
<Operation on the watch>
The function hand on the upper
right sub dial points the area
shown on the right (“
ON
” area)
when registration completes
successfully and the watch is
connected with the iPhone.
“
ACT
” indication ends and the second hand
returns to second indication.
8
Change the mode to either [
TME
] (or [
L-TM
]) to
finish the procedure.
(See page
3b
.)
Proximity Connect
ON