YOUR HANDBOOK ON THE INTERNET! CITROËN lets you view your vehicle's documentation on line, to see earlier versions and the latest information, simply and free of charge. Connect to http://service.citroen.
We draw your attention to the following... Your vehicle is fitted with only some of the equipment described in this document, depending on the trim level, version and the specifications for the country in which it is sold. CITROËN has a presence on every continent, a complete product range, bringing together technology and a permanent spirit of innovation, The fitting of electrical equipment or accessories which are not recommended by CITROËN may result in a failure of your vehicle's electronic system.
CONTENTS FAMILIARISATION 4 Î 30 ■ Eco-driving I - MONITORING 29 31 Î 44 ■ Instrument panels ■ Indicator and warning lamps ■ Indicators II - MULTIFUNCTION SCREENS ■ ■ ■ ■ ■ Monochrome screen A Monochrome screen C Colour screen (MyWay) NaviDrive colour screen Trip computer 31 33 42 45 Î 55 45 47 50 52 53 III - COMFORT ■ ■ ■ ■ ■ ■ ■ ■ ■ Ventilation Manual air conditioning Digital air conditioning Scented air freshener Front seats Rear seats Seat modularity Mirrors Steering wheel adjustment IV - AC
CONTENTS VIII - SAFETY ■ ■ ■ ■ ■ ■ ■ ■ ■ Direction indicators Hazard warning lamps Horn Tyre under-inflation detection Braking assistance systems Trajectory control systems Emergency or assistance call Seat belts Airbags IX - DRIVING ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 126 Î 138 126 126 126 127 128 129 130 131 135 139 Î 172 Electric parking brake Hill start assist Manual gearbox Gear efficiency indicator 6-speed electronic gearbox system Stop & Start Automatic gearbox Fixed centred controls steering wheel Spee
FA M I L I A R I S AT I O N EXTERIOR Stop & Start This system puts the engine temporarily into standby during stops in the traffic (red lights, traffic jams, etc...). The engine restarts automatically as soon as you want to move off. Stop & Start reduces fuel consumption, exhaust emissions and noise when stationary. 153 Front/rear parking sensors Sensors, located in the bumpers, detect obstacles.
EXTERIOR Panoramic sunroof 91 90 Pneumatic rear suspension This enhances driving comfort and maintains a constant body height, whatever the vehicle load. 171 Exterior side spotlamps These light up the zones facing the driver’s and passenger’s doors. 98 Door mirrors With electric foldback. Automatically tilts in reverse gear.
OPENING FA M I L I A R I S AT I O N Remote control key A. B. C. D. Fuel tank To release the bonnet, pull the lever located under the dashboard left hand end towards you. Then operate the safety catch at the front of the bonnet, Capacity: approximately 60 litres. Central locking Unlocking Remote lighting control Folding/unfolding the key Bonnet stay: Unclip the stay and insert it into the notch.
OPENING Opening the tailgate This opening gives easy access to the boot, even if you are parked close to a wall or to another vehicle. ) Press control 1. You cannot open the tailgate if the rear screen is already open. Closing the tailgate Opening Load: 22 kg maximum. The Modubox comprises a shopping trolley and a flexible bag which can be used independently of each other depending on your needs. 112 ) Press control 2. The grip 4 is in line with the rear wiper. Closing ) Lower the rear screen.
BOOT CITROËN C4 Picasso FA M I L I A R I S AT I O N Luggage cover in two sections 8 CITROËN Grand C4 Picasso Luggage cover blind 111 Access to spare wheel Torch 187 Pneumatic rear suspension Allows the height of the rear of the vehicle to be adjusted 116 112 Torch 171 Temporary puncture repair kit Depending on model, the kit is located either in the boot well or in the compartment under the left hand second-row passenger (open the flap by turning the screw a quarter turn).
Electric parking brake For holding and releasing the vehicle. Operation is automatic with manual operation possible using the dashboard control. 139 6-speed electronic gearbox system This offers a fully automatic mode, a manual mode and an auto-sequential mode which combines the advantages of the automatic and manual modes, using the steering mounted paddles.
FA M I L I A R I S AT I O N INSTRUMENTS AND CONTROLS 10
INSTRUMENTS AND CONTROLS 1. Controls: - Lighting - Direction indicators - Front and rear foglamps 8. Controls: - Trip mileage recorder reset button - Lighting rheostat 2. Paddles for automatic gearbox or 6-speed electronic gearbox system 9. Warning lamps display (with the MyWay or NaviDrive multifunction screen) 3. Cruise control and speed limiter (steering mounted controls) 10. Electric parking brake 4. Direction indicator warning lamps 11. Instrument panel 20.
FA M I L I A R I S AT I O N INSTRUMENTS AND CONTROLS 12
1. Controls: - Electric windows - Child lock 2. Side window demist/defrost vent Side air vent 3. Driver’s air conditioning controls 4. Driver’s front airbag 5. Right hand upper storage 10. Quarter light demist/defrost vent 17. Audio and telematics system 11. Windscreen demist/defrost vent 18. Scented air freshener 12. Sunshine sensor 19. Cooled storage 13. Passenger’s air conditioning controls 20. USB port (or blanking plug) 14. Lower glove box: - Air freshener clips - Various storage 7.
S I T T I N G C O M F O R TA B LY FA M I L I A R I S AT I O N Adjusting the steering wheel Automatic photochromatic rear view mirror The steering wheel can be adjusted for height and reach. Release the steering wheel by pulling lever A towards you. Adjust the position of the steering wheel then lock it pushing the lever fully back. 77 Child surveillance mirror This operates with the ignition switched on.
S I T T I N G C O M F O R TA B LY Manual adjustments Electric adjustments Head restraint Armrest Backrest angle Seat height adjustment 1. Adjustment of seat height, angle and forwards-backwards position 2. Adjustment of backrest angle and lumbar support 3. Driver: storing driving positions The seats can also be adjusted on a temporary basis: - on opening one of the front doors, - after switching on the ignition.
FA M I L I A R I S AT I O N S I T T I N G C O M F O R TA B LY Adjusting the seat belt height Electric windows controls Sliding sun visors To adjust the seat belt, squeeze the control and slide it in the direction required. From the driver’s seat position, the controls located on the door are used to operate the electric windows. ) Slide the blind on the visor to the desired position by pushing at A. The blinds are extended on the sun visor rails. ) Fold the visor downwards, to prevent being dazzled.
V E N T I L AT I O N Recommended settings Heating/manual air conditioning: Operate For... Cooling or Fully cold Maximum to start, to start, then personal then personal settings settings Heating or Fully hot Maximum to start, to start, then personal then personal settings setting Demisting Defrosting - Fully hot ON ON when starting, then OFF ON when starting, then OFF FA M I L I A R I S AT I O N - OFF Digital air conditioning: the fully automatic mode is recommended - press "AUTO".
MONITORING Instrument panel Seat belts not fastened/ unfastened warning lamp with multifunction screen A or C FA M I L I A R I S AT I O N 31 Manual central locking This warning lamp informs you if the driver’s or front passenger’s seat belt is not fastened (depending on model), and if the front passenger’s (depending on model) or the second-row passengers’ seat belts are unfastened. The illuminated positions represent those whose seat belts are not fastened/ unfastened.
PA S S E N G E R S A F E T Y Child lock Front airbags ISOFIX mounting system The rear doors are locked by operating the lever using the key (aperture at an angle). Deactivation of the front passenger’s airbag 1. Insert the key in lock A. 2. Select the "OFF" position. 3. Remove the key. Electric control 135 Pressing the button prohibits operation of the electric windows from the rear of the vehicle and opening of the rear doors from inside.
PA S S E N G E R S A F E T Y Seat belts FA M I L I A R I S AT I O N Second row centre seat belt 20 Using the third-row passenger seat belts (CITROËN Grand C4 Picasso) ) Insert tongue C into the buckle on the right, then insert the second tongue D into the buckle on the left. 132 Take care to attach the third-row passenger seat belts to the rings provided for this purpose. Do not attach the belts to the load anchorage points marked with a red cross (see illustration above).
INTERIOR "Comfort" position Forwards-backwards adjustment The 3 second-row seats are independent of each other and are all the same width. They can all be adjusted to the "comfort" position. Lift up control A, located at the front of the seat, and adjust the seat into the desired position. Placing a seat in the "comfort" position ) Pull on strap B. The backrest reclines and the seat base pivots slightly.
INTERIOR SECOND ROW SEATS FA M I L I A R I S AT I O N Folding the seats Repositioning the seats Return the rigid panels of the secondrow seats to their initial (upright) position and lock them in position (CITROËN Grand C4 Picasso). Raise the backrest and push it backwards until it locks in position. From outside ) Pull firmly upwards on strap C, as indicated by the red arrow, to unlock the seat ; keep pulling until the seat is fully folded.
INTERIOR Installing the seats Fold the concertina boards (1 2 3) arranged above each of the third-row seats. Pull on the black strap F, located on the seat backrest. 74 Before moving the third-row seats, do not forget to lock in the rigid panels first (located at the base of the second-row seat backrests). Stowing the seats Access to third-row seats Put the three sections of the concertina boards (1 2 3) to their vertical position, then pull on the red strap G.
FA M I L I A R I S AT I O N DRIVING Lighting stalk Wiper stalk Ring A Stalk C: windscreen wipe 1. 2. 3. 4. Switching on "AUTO" mode ) Press the stalk down and release. Off Automatic illumination of headlamps Sidelamps Dipped/main beam headlamps 94 Ring B Front foglamps Rear foglamp 95 Under certain climatic conditions (low temperature, humid), condensation may appear on the inner surfaces of the headlamps and rear lamps.
DRIVING This device combines: - automatic functions: Automatic application when the engine stops and automatic release on use of the accelerator (automatic operation by default); - manual use: Manual application/ release of parking brake is possible by operating control lever A. Before leaving the vehicle, check that the electric parking brake warning lamp P (red) is on fixed (not flashing). If you leave the vehicle with the engine running, apply the parking brake manually.
FA M I L I A R I S AT I O N DRIVING 6-speed electronic gearbox system Automatic gearbox R Reverse N Neutral A Automatic mode M Manual mode Using control paddles 1 "+" and 2 "-": - gear changing in manual mode, - temporary manual operation in automatic mode. P Park R Reverse N Neutral D Automatic mode M Sequential mode Using control paddles 1 "+" and 2 "-": - gear changing in sequential mode, - temporary manual operation in automatic mode.
DRIVING Stop & Start with the 6-speed electronic gearbox system ; at speeds below 4 mph (6 km/h), press the brake pedal or put the selector lever into neutral (position N). - In certain circumstances the STOP mode may not be available; the "ECO" warning lamp flashes for a few seconds, then goes off. 153 with the selector lever in position A or M, release the brake pedal, or with the selector lever in position N and the brake pedal released, change to position A or M, or select reverse gear.
FA M I L I A R I S AT I O N DRIVING Ignition switch Speed limiter Cruise control ● 1. 2. 3. 4. 1. Cruise control mode On/Off. 2. Programming a speed/Reducing the programmed value. 3. Cruise control On/Off. 4. Programming a speed/Increasing the programmed value. In order to be programmed or activated, the vehicle speed must be higher than 25 mph (40 km/h), with at least fourth gear engaged on a manual gearbox (second gear for the 6-speed electronic gearbox system or automatic gearbox).
ECO-DRIVING Optimise the use of your gearbox Drive smoothly Control the use of your electrical equipment With a manual gearbox, move off gently, change up without waiting and drive by changing up quite soon. If your vehicle has the system, the gear efficiency indicator invites you to change up; it is displayed in the instrument panel, follow its instructions. Maintain a safe distance between vehicles, use engine braking rather than the brake pedal, and press the accelerator progressively.
FA M I L I A R I S AT I O N Switch off the headlamps and front foglamps when the level of light does not require their use. Avoid running the engine before moving off, particularly in winter; your vehicle will warm up much faster while driving. As a passenger, if you avoid connecting your multimedia devices (film, music, video game...), you will contribute towards limiting the consumption of electrical energy, and so of fuel. Disconnect your portable devices before leaving the vehicle.
MONITORING MONOCHROME INSTRUMENT PANEL (WITH MULTIFUNCTION SCREEN A) 6. 7. 8. 9. TWO-TONE INSTRUMENT PANEL (WITH MULTIFUNCTION SCREEN C) Fuel gauge Trip mileage recorder Multifunction screen A/C Total mileage recorder In this zone, the following information appears in succession when the ignition is switched on: - service indicator, - engine oil level indicator, - total mileage recorder. I Controls A. Lighting rheostat (available day and night) B. Trip mileage recorder reset Central screen 1.
MONITORING I INSTRUMENT PANEL WITH MyWay OR NaviDrive MULTIFUNCTION SCREEN 7. Gear efficiency indicator for a manual gearbox or selector lever position and gear for the electronic gearbox system or automatic gearbox 8. Trip mileage recorder 9. Total mileage recorder In this zone, the following information appears in succession when the ignition is switched on: - service indicator, - engine oil level indicator, - total mileage recorder. 10. Warning lamp zone. Controls A.
MONITORING Indicator and warning lamps Visual indicators informing the driver that a system is in operation (operation or deactivation indicator lamps) or of the occurrence of a fault (warning lamp). When the ignition is switched on Certain warning lamps come on for a few seconds when the vehicle's ignition is switched on. When the engine is started, these same warning lamps should go off. If they remain on, before moving off, refer to the information on the warning lamp concerned.
MONITORING I Warning lamp is on Cause Front foglamps fixed. The front foglamps are switched on. Turn the ring on the stalk rearwards twice to switch off the front foglamps. Rear foglamps fixed. The rear foglamps are switched on. Turn the ring on the stalk rearwards to switch off the rear foglamps. Diesel engine pre-heating fixed. The ignition switch is at the 2nd position (ignition on). Wait until the warning lamp has switched off before starting.
MONITORING Warning lamp Passenger's airbag system is on Cause Action/Observations fixed. The control switch, located in the glove box, is in the "ON" position. The passenger's front airbag is activated. In this case, do not install a rear-facing child seat. Turn the control switch to the "OFF" position to deactivate the front passenger's airbag. In this case you can install a rear-facing child seat. fixed. When the vehicle stops (red lights, traffic jams, ...
MONITORING I Deactivation indicator lamps If one of the following indicator lamps comes on, this confirms that the corresponding system has been switched off intentionally. This is may be accompanied by an audible signal and a message on the multifunction screen. Warning lamp Passenger's airbag system ESP/ASR 36 is on Cause Action/Observations fixed. The control, located in the glove box, is set to the OFF position. The passenger's front airbag is deactivated.
MONITORING Warning lamps When the engine is running or the vehicle is being driven, the illumination of one of the following warning lamps indicates a fault which requires action on the part of the driver. Any fault resulting in the illumination of a warning lamp must be investigated further by reading the associated message in the multifunction screen. If you encounter any problems, do not hesitate to contact a CITROËN dealer or a qualified workshop.
MONITORING I Warning lamp is on Cause Action/Observations fixed, associated with the STOP warning lamp. The braking system fluid level is too low. You must stop as soon as it is safe to do so. Top up with brake fluid recommended by CITROËN. If the problem persists, have the system checked by a CITROËN dealer or a qualified workshop. fixed, associated with the STOP and ABS warning lamp. The electronic brake force distribution (EBFD) system has a fault. You must stop as soon as it is safe to do so.
MONITORING Warning lamp Deactivation of the automatic functions of the electric parking brake Dynamic stability control (ESP/ASR) is on Action/Observations fixed. The "automatic application" (on switching off the engine) and "automatic release" functions are deactivated or faulty. Activate the function (according to country) via the vehicle configuration menu or contact a CITROËN dealer or a qualified workshop if automatic application/release is not possible.
MONITORING I Warning lamp Low fuel level is on fixed, accompanied by an audible signal and a message on the multifunction screen. fixed. Foot on the brake pedal Cause When it first comes on there remains approximately 7 litres of fuel in the tank. You must refuel as soon as possible to avoid running out of fuel. This warning lamp will come on every time the ignition is switched on, until sufficient fuel has been added. Fuel tank capacity: 60 litres.
MONITORING Warning lamp is on Cause Action/Observations Maximum coolant temperature fixed red. The temperature of the cooling system is too high. Stop as soon as it is safe to do so. Wait until the engine has cooled down before topping up the level, if necessary. If the problem persists, contact a CITROËN dealer or qualified workshop. Battery charge fixed. The battery charging circuit has a fault (dirty or loose terminals, slack or cut alternator belt, ...).
MONITORING I Service indicator System which informs the driver when the next service is due, in accordance with the manufacturer's servicing schedule. The point at which the service is due is calculated from the last indicator zero reset. It is determined by two parameters: - the distance travelled, - the time elapsed since the last service. More than 1 000 km remain before the next service is due For 5 seconds after the ignition is switched on, the spanner symbolising the service operations comes on.
MONITORING Service indicator zero reset After each service, the service indicator must be reset to zero. The procedure for resetting to zero is as follows: ) switch off the ignition, ) press and hold the trip distance recorder zero reset button, ) switch on the ignition; the distance recorder display begins a countdown, ) when the display indicates "=0", release the button; the spanner disappears.
MONITORING I Distance recorders Lighting dimmer The total and trip distances are displayed for thirty seconds when the ignition is switched off, when the driver's door is opened and when the vehicle is locked or unlocked. Permits manual adjustment of the brightness of the instruments and controls to suit the ambient light level. Only operates when the vehicle lighting is on, with the exception of the daytime running lamps.
M U LT I F U N C T I O N S C R E E N S MONOCHROME SCREEN A Controls Main Menu Displays in the screen II This screen can display the following information: - time - date - ambient temperature When the ambient temperature is between +3 °C and -3 °C, the temperature display flashes (risk of ice). The ambient temperature displayed may be higher than the actual temperature if the vehicle is parked in the sun. - the current audio source, - trip computer (see the end of the section). Alert messages (e.g.
M U LT I F U N C T I O N S C R E E N S Vehicle config II Radio-CD With the Audio system on, you can activate or deactivate functions of the radio (RDS station tracking, REG mode), CD or CD changer (CD introscan, shuffle, repeat). For more information on the "RadioCD" application, refer to the Audio system section in "Audio and Telematics".
M U LT I F U N C T I O N S C R E E N S MONOCHROME SCREEN C Controls Main Menu Displays in the screen II This screen can display the following information: - time - date, - ambient temperature When the ambient temperature is between +3 °C and -3 °C, the temperature display flashes (risk of ice). The ambient temperature displayed may be higher than the actual temperature if the vehicle is parked in the sun.
M U LT I F U N C T I O N S C R E E N S Bluetooth telephone (hands-free system) II With the Audio system on, you can configure your Bluetooth hands-free system (pairing), view the various telephone directories (calls log, services..) and manage calls (call, hang up, double call, secret mode...). For more information on the "Telephone" application, refer to the Audio system section in "Audio and Telematics". Trip computer Audio functions You can see information on the state of the vehicle.
M U LT I F U N C T I O N S C R E E N S Define the vehicle parameters You can activate or deactivate the following systems: - rear wiper coupled with reverse gear (refer to the "Visibilty" section), - automatic guide-me-home lighting, - directional headlamps, - automatic functions (application/ release) of the electric parking brake* - selective door locking, - daytime running lamps (refer to the "Visibilty" section), Personalisation Configuration This menu is used to activate/deactivate the following funct
M U LT I F U N C T I O N S C R E E N S MyWay MULTIFUNCTION SCREEN II 50 Controls! Menus in the control panel Displays in the screen This screen can display the following information: - time, - date, - ambient temperature When the ambient temperature is between +3 °C and -3 °C, the display flashes (risk of ice). The temperature displayed may be higher that the actual temperature if the vehicle has been parked in the sun.
M U LT I F U N C T I O N S C R E E N S SETUP menu ) Press the "SETUP" button to open the configuration menu. This allows you to select from the following functions: - "System language", - "Date and time", - "Display", - "Vehicle", - "Units", - "System". System language This menu allows you to select the language used by the display: Deutsch, English, Espanol, Français, Italiano, Nederlands, Polski, Portugues, Türkçe*.
M U LT I F U N C T I O N S C R E E N S NAVIDRIVE MULTIFUNCTION SCREEN II Controls Displays in the screen The screen can display the following information: - time - date - ambient temperature When the ambient temperature is between +3 °C and -3 °C, the temperature display flashes (risk of ice). The ambient temperature displayed may be higher than the actual temperature if the vehicle is parked in the sun. - alert messages and state of vehicle systems, displayed temporarily.
M U LT I F U N C T I O N S C R E E N S Main Menu TRIP COMPUTER Press button A to display the "Main Menu": System which provides current information concerning the trip travelled (range, fuel consumption...). Navigation/Guidance Monochrome screen A The trip computer provides the following information: - range, - current fuel consumption, - distance travelled, - average fuel consumption, - average speed. ) The next press then returns you to the normal display.
M U LT I F U N C T I O N S C R E E N S TRIP COMPUTER II Display of information System which provides current information concerning the route travelled (range, fuel consumption, …) in the multifunction screen. - the trip "2" group with: ● the distance travelled, ● the average fuel consumption, ● the average speed, for the second trip.
M U LT I F U N C T I O N S C R E E N S A few definitions… Range (miles or km) Current fuel consumption (mpg or l/100 km or km/l) This is the average fuel consumption during the last few seconds. This indicates the distance which can still be travelled with the fuel remaining in the tank in relation to the average fuel consumption over the last few miles (kilometres) travelled. This function is only displayed from 20 mph (30 km/h).
COMFORT RECOMMENDED SETTINGS FOR VENTILATION, HEATING AND AIR CONDITIONING Air intake Check that the exterior grille for the air intake at the bottom of the windscreen, is clean and free of dead leaves, snow, etc. III Air distribution 1. Windscreen demisting/defrosting vents. 2. Front quarter light window demisting/defrosting vents. 3. Front side window demisting/ defrosting vents. Adjustable side air vents. 4. Adjustable central air vents. 5. Front passenger footwell air outlets. 6.
COMFORT Air vents Air conditioning The air vents to the face have grilles and thumb wheels to adjust the air flow and direction (up-down, rightleft). To ensure that your system operates correctly, it is recommended that you have it checked regularly. Water arising from condensation in the air conditioning drains away through a hole provided for this purpose. A pool of water may thus form under the vehicle when stationary.
COMFORT MANUAL AIR CONDITIONING The air conditioning system operates with the engine running. III A. DRIVER'S CONTROL PANEL The level of air flow is shown by the progressive lighting of the warning lamps depicting the fan blades 1. By reducing the flow to minimum, you deactivate the air conditioning system (OFF). To maintain an acceptable level of comfort in the passenger compartment, you should not leave this control too long in the OFF position. 2.
COMFORT 6. Demisting/defrosting the rear screen 8. Adjustment of the fan air temperature This function operates only if the engine is running. ) Press button 6 to activate/deactivate the electric demisting/ defrosting of the rear screen and door mirrors. The warning lamp comes on. This control is for adjusting the temperature of the air in the passenger compartment. It can be used in cold weather as well as in hot weather, provided the air conditioning is active.
COMFORT DIGITAL AIR CONDITIONING The air conditioning system operates with the engine running. III A. DRIVER'S CONTROL PANEL For this facility to operate, it is recommended that all air vents are kept open. Using the AUTO mode will prevent the formation of mist inside the vehicle in cold or humid weather. When starting from cold, in order to avoid a rush of cold air, the air fan attains its optimum level progressively.
COMFORT 3. Adjustment of air fan speed/Activation of the "REST" function Adjustment of air flow To adjust the flow of air, press the button: This function is available when you switch on the ignition as well as when you stop the engine. The air conditioning control screens come on and the symbol representing the air fan is displayed while the function is available. to increase the air flow, to decrease the air flow (this button also has the REST function).
COMFORT 5. Air recirculation III This button activates the recirculation of air within the passenger compartment and also has an automatic function. ) Press button 5 to cut off the intake of air from outside and to activate recycling of the air in the passenger compartment. the warning lamp comes on. Whilst retaining the other adjustments, this function prevents unpleasant odours or fumes entering the vehicle. Avoid extended use of air recirculation (risk of deterioration of air quality and misting).
COMFORT 9. Rapid demisting/defrosting of the front and rear windows - B. PASSENGER CONTROL PANELS By default, in AUTO position, the adjustment of the air flow is aligned on the front ventilation. ) Rotate the button to decrease or increase the air flow. Press button 9. The warning lamp comes on.
COMFORT ADDITIONAL AIR CONDITIONING C. REAR PASSENGER CONTROL PANELS (RIGHT/LEFT) 13. Adjustment of temperature III The rear passengers can adjust their temperature controls independently via buttons + and -. Their setting cannot be greater than that of the driver by more than 2. Attainment of this maximum setting is confirmed by the flashing of its display. 14. Adjustment of air fan speed Additional air conditioning allows you to optimise comfort levels in warm weather conditions.
COMFORT SCENTED AIR FRESHENER To remove the air freshener To insert the air freshener The scented air freshener releases a fragrance into the passenger compartment via the central air vents. III The air freshener contains an empty cartridge when your vehicle is delivered. You therefore need to insert a cartridge in order to use the air freshener. Adjustment of flow ) Press the button A, rotating it a quarter turn to the left as far as it will go. ) Remove the air freshener from the dashboard.
COMFORT Replacing a cartridge Air freshener button The recharge for the air freshener consists of a cartridge B and its sealed container C. ) Remove the protective film D. ) Place the head of the cartridge B on the button A of the air freshener. ) Rotate it a quarter turn to lock it on the button and remove the container. ) Insert the air freshener into its housing. You can change cartridges at any time, keeping the used cartridges in their original containers.
COMFORT FRONT SEATS 3. Seat height adjustment Raise or lower the the control the number of times necessary to obtain the position desired. 4. Backrest angle Operate the control and adjust the angle of the backrest. It is possible to incline the backrest 45° rearwards by tilting it until it locks; to unlock it, lift the control. III 5. Armrest To adjust the position of the armrest, pull it up and then fully down, and then raise it to the desired position. 6. Head restraint MANUAL ADJUSTMENTS 1.
COMFORT FRONT SEATS ELECTRIC ADJUSTMENTS 2. Adjustment of backrest angle and lumbar support Heated seats control Push the top of control forwards or backwards to adjust the backrest angle. III Raise or lower control to increase or decrease the lumbar support. 1. Adjustment of the seat height and angle, forwards-backwards Raise or lower the front of control to raise or lower the front of the seat base (on driver’s seat). Raise or lower the rear of control to raise or lower the seat.
COMFORT Storing driving positions System which registers the electrical settings of the driver's seat and door mirrors. It enables you to store and recall two positions using the buttons on the side of the driver's seat. Storing a position Recalling a stored position Using buttons M/1/2 ) Switch on the ignition. ) Adjust your seat and the door mirrors. ) Press button M, then press button 1 or 2 within four seconds. An audible signal indicates that the position has been stored.
COMFORT REAR HEAD RESTRAINTS SECOND ROW SEATS "Comfort" position Forwards-backwards adjustment III The rear head restraints can be removed and have two positions: - high, position for use, - low, storage position. To raise a head restraint, pull it upwards. To lower it, press the lug then the head restraint. To remove it, place it in the high position, push the lug and pull it upwards. To refit it, engage the head restraint rods in the holes taking care to remain in line with the seat back.
COMFORT SECOND ROW SEATS (C4 PICASSO) Folding a seat Repositioning a seat ) Raise the backrest and push it rearwards until it locks in position Panels behind the second row seats III Always supervise any movements of seats by children. Each seat can be folded onto the floor to enable you to modify your vehicle’s interior space. ) Pull firmly upwards on strap C, as indicated by the red arrow, to unlock the seat; keep pulling until the seat is fully folded.
COMFORT SECOND ROW REAR SEATS (GRAND C4 PICASSO) III Each seat can be folded onto the floor to form a flat surface, thus enabling you to adapt your vehicle’s interior space. From the boot (when loading, for example) You can fold the second-row seat(s) from the boot, having first folded the third-row seats. ) Pull on the strap D to unlock the chosen seat, push the backrest gently forwards. To prevent any damage to the mechanism, the strap D unclips under excessive force.
COMFORT "Cinema seat" position Access to the third row seats Exit from the third row seats ) Hold the lever E in the raised position. The seat unlocks and the seat cushion comes up against the backrest. ) Push the seat backrest, still holding the lever E in the raised position. If the table on the back of the firstrow seat is down, close it to enable this operation. This position allows you to free up space between the first row and the second row. Pull the lever E under the seat.
COMFORT THIRD ROW SEATS (GRAND C4 PICASSO) Unfolding the seat Concertina boards III Two rigid concertina boards, which cannot be separated from the vehicle, cover the 2 third-row seats, when these are in the folded position. ) Return the second-row rigid panels to their initial position and lock them. ) Having folded your concertina board, pull on the control F located behind the seat backrest. The backrest pivots rearwards, pulling the seat base with it. The seat locks in the open position.
COMFORT SEAT MODULARITY AND THE VARIOUS CONFIGURATIONS Examples of C4 Picasso seat configurations Examples of seat configurations Grand C4 Picasso III 5 seats 3 seats 7 seats 6 seats Maximum loadspace 4 seats Maximum loadspace 5 seats 4 seats For easy modification of your interior vehicle space, all the rear seats can be individually folded: onto the second-row floor, and under the third-row floor (in the case of the Grand C4 Picasso).
COMFORT MIRRORS Door mirrors III Each mirror is adjustable to provide the rear view needed for overtaking or parking. They can also be folded for parking in confined spaces. The objects observed are, in reality, closer than they appear. Take this into account in order to correctly judge the distance of vehicles approaching from behind. The demisting/defrosting of the door mirrors is linked to that of the rear screen. Folding ) From outside: lock the vehicle using the remote control or the key.
COMFORT Rear view mirror Automatic day/night model STEERING WHEEL ADJUSTMENT The height and reach of the steering wheel can be adjusted to adapt the driving position to the size of the driver. Adjustable mirror providing a central rearward view. Equipped with an anti-dazzle system, which darkens the mirror glass: this reduces the nuisance to the driver caused by the headlamps from following vehicles, low sun...
ACCESS REMOTE CONTROL KEY System which permits central unlocking or locking of the vehicle using the door lock or remotely. It is also used to locate the vehicle, activate the guideme-home lighting and start the engine, as well as providing protection against theft. IV Complete unlocking using the key ) Turn the key to the left in the driver's door lock to unlock the vehicle. Unlocking is confirmed by rapid flashing of the direction indicators for approximately two seconds.
ACCESS Locking the vehicle Normal locking using the remote control ) Briefly press the closed padlock to lock the vehicle. ) Make a long press on the closed padlock to lock the vehicle and also close the windows and the panoramic sunroof blind. Normal locking using the key ) Turn the key to the right in the driver's door lock to lock the vehicle. Locking is confirmed by fixed lighting of the direction indicators for approximately two seconds. According to version, the door mirrors fold at the same time.
ACCESS Deadlocking using the key IV Remote operation of lighting A press on this button brings on the temporary illumination of sidelamps, dipped beam headlamps, number plate lamps and the exterior side spotlamps located underneath the door mirrors. A second press before the end of the timed period cancels the command. Deadlocking is confirmed by fixed lighting of the direction indicators for approximately two seconds. According to version, the door mirrors fold at the same time.
ACCESS STARTING Steering lock 1. "S": After removing the key, turn the steering wheel to lock the steering. The key can only be removed in position S. 2. "M": Ignition switched on, the steering is unlocked (by turning the key to position M, move the steering wheel gently if necessary). 3. "D": Starter position.
ACCESS Remote control problems IV Changing the battery Following disconnection of the vehicle battery, replacement of the remote control battery or in the event of a remote control malfunction, you can no longer unlock, lock or locate your vehicle. ) First of all, use the key in the lock to unlock or lock your vehicle. ) Then, reinitialise the remote control. Reinitialisation ) Switch off the ignition. ) Turn the key to position 2 (Ignition on). ) Press the closed padlock immediately for a few seconds.
ACCESS Lost keys Locking the vehicle Visit a CITROËN dealer with the vehicle's registration document, your personal identification documents and if possible the key code label. The CITROËN dealer will be able to find the key code and the transponder code required to order a new key. Driving with the doors locked may make access to the passenger compartment by the emergency services more difficult in an emergency.
ACCESS ALARM System which protects and provides a deterrent against theft and breakins. It provides the following types of monitoring. IV - Exterior perimeter The system checks for opening of the vehicle. The alarm is triggered if anyone tries to open a door, the boot, the bonnet... - Interior volumetric The system checks for any variation in the volume in the passenger compartment. The alarm is triggered if anyone breaks a window, enters the passenger compartment or moves inside the vehicle.
ACCESS Locking the vehicle with exterior perimeter monitoring only Deactivate the interior volumetric monitoring to avoid unwanted triggering of the alarm in certain cases such as: - leaving a pet in the vehicle, - leaving a window partially open, - washing your vehicle, Deactivation of the interior volumetric monitoring ) Switch off the ignition. ) Within ten seconds, press the button until the indicator lamp is on continuously. ) Get out of the vehicle.
ACCESS ELECTRIC WINDOWS One-touch electric windows System intended to open or close a window manually or automatically. Fitted with a safety anti-pinch system and a system for deactivation in the event of misuse of the rear controls. There are two options: - manual mode ) Press or pull the control gently. The window stops when the control is released. IV - 1. Driver's electric window control. 2. Passenger's electric window control. 3. Rear right electric window control. 4.
ACCESS Reinitialisation If a window does not rise automatically, its operation must be reinitialised: ) pull the control until the window stops, ) release the control and pull it again until the window closes fully, ) continue to hold the control for approximately one second after the window has closed, ) press the control to lower the window automatically to the low position, ) when the window has reached the low position, press the control again for approximately one second.
ACCESS DOORS From inside Opening Manual central locking control System for locking or unlocking the vehicle - the doors and boot - from the driving position. From outside IV ) Pull the interior control lever of a front door; this unlocks the vehicle completely. ) After unlocking the vehicle completely using the remote control or the key, pull the door handle. When the selective unlocking is activated, the first press of the remote control unlocking button permits unlocking of the driver's door only.
ACCESS In the event of a fault with the central locking, you must disconnect the battery to lock the boot and so ensure the complete locking of the vehicle. Unlocking ) Press this button again to unlock the vehicle. The red indicator lamp on the button goes off. If the vehicle is locked or deadlocked from the outside, the red indicator lamp flashes and button A is inactive. ) In this case, use the remote control or the key to unlock the vehicle.
ACCESS BOOT Opening ) Past the balancing point, allow the tailgate to lower and close itself (do not assist it or slow it down). If the tailgate is not closed correctly: - IV - when the engine is running, this warning lamp comes on, accompanied by a message in the multifunction screen for a few seconds, when the vehicle is moving (speed above 6 mph (10 km/h)), this warning lamp comes on, accompanied by an audible signal and a message in the multifunction screen for a few seconds.
ACCESS Emergency boot release PANORAMIC SUNROOF Closing the roof blind System for mechanical unlocking of the boot in the event of a battery or central locking malfunction. It is fitted with an electrically controlled blind. ) Rotate the control knob B to position 0 to close the roof blind. Recommendations - Pressing the locking button on the remote control for more than two seconds will close the blind (practical when, for example, you leave your vehicle in a sunlit car park).
ACCESS FUEL TANK Refuelling Capacity of the tank: approximately 60 litres. Low fuel level IV When the low fuel level is reached, this warning lamp comes on in the instrument panel, accompanied by an audible warning and a message in the multifunction screen. When it first comes on, around 7 litres of fuel remain in the tank. Until sufficient fuel has been added, this warning lamp comes on every time the ignition is switched on, accompanied by an audible signal and a message.
ACCESS The petrol or Diesel engine of your vehicle is fitted with a catalytic converter, a device which helps to reduce the level of harmful emissions in the exhaust gases. For petrol engines, you must use unleaded fuel. The filler neck is narrower, allowing only unleaded petrol nozzles to be introduced. If you have put in the wrong fuel for your vehicle, you must have have the tank drained and refilled with the correct fuel before you start the engine.
VISIBILITY EXTERIOR LIGHTING CONTROLS Control stalk for the selection and control of the various front and rear lamps providing the vehicle's lighting. Main lighting V The various front and rear lamps of the vehicle are designed to adapt the driver's visibility progressively in relation to the climatic conditions: - sidelamps, to be seen, - dipped beam headlamps to see without dazzling other drivers, - main beam headlamps to see clearly when the road is clear.
VISIBILITY C. Foglamps selection ring. The foglamps operate with the sidelamps and the dipped and main beam headlamps. Model with rear foglamp only - 1st turn forwards: rear foglamp on. 1st turn rearwards: rear foglamp off. Model with front and rear foglamps - 1st turn forwards: front foglamps on. 2nd turn forwards: rear foglamps on. 1st turn rearwards: rear foglamps off. 2nd turn rearwards: front foglamps off. In some weather conditions (e.g.
VISIBILITY LED lamps Daytime running lamps Daytime lighting, compulsory in certain countries, which comes on automatically when the engine is started making the vehicle more visible to other users. V They come on when the engine is started. Depending on the destination country, they are used for: - daytime running lamps in day mode and sidelamps in night mode, or - sidelamps in day and night mode Where LED lamps are fitted, the filament bulbs for the sidelamps in the front lamp units are not used.
VISIBILITY Automatic illumination of headlamps Automatic "guide-me-home" lighting When a low level of ambient light is detected by a sunshine sensor, the number plate lamps, sidelamps and dipped beam headlamps are switched on automatically, without any action on the part of the driver. They can also come on if rain is detected, at the same time as automatic operation of the windscreen wipers.
VISIBILITY EXTERIOR SIDE SPOTLAMPS MANUAL HEADLAMP ADJUSTMENT Switching on To avoid dazzling other road users, the height of the halogen bulb headlamps must be adjusted according to the load in the vehicle. To do this, turn the control, located below the dashboard to the right of the driver, to the appropriate position: 0. 1 or 2 people in the front seats. -. 3 people. 1. 4 to 7 people. -. Intermediate setting. 2. 4 to 7 people + maximum authorised loads. -. Intermediate setting. 3.
VISIBILITY DIRECTIONAL LIGHTING Programming When the dipped or main beam headlamps are on, this function enables the light beam to follow the direction of the road. The use of this function, coupled with the xenon headlamps only, considerably improves the quality of your lighting when cornering. The function is activated or deactivated via the multifunction screen configuration menu.
VISIBILITY WIPER CONTROLS Manual controls System for selection and control of the various front and rear wiping modes for the elimination of rain and cleaning. The vehicle's front and rear wipers are designed to improve the driver's visibility progressively according to the climatic conditions. The wiper commands are issued directly by the driver by means of the stalk A and the ring B. Rear wiper Windscreen wipers A. Wiping speed selection stalk: V fast (heavy rain), normal (moderate rain), B.
VISIBILITY Reverse gear When reverse gear is engaged, the rear wiper will come into operation if the windscreen wipers are operating. Programming The function is activated or deactivated via the vehicle configuration menu. This function is activated by default. Windscreen and headlamp wash ) Pull the windscreen wiper stalk towards you. The windscreen wash then the windscreen wipers operate for a fixed period. The headlamp washers only operate when the dipped beam headlamps are on.
VISIBILITY Special position of the windscreen wipers V This position permits release of the windscreen wiper blades. It is used for cleaning or replacement of the blades. It can also be useful, in winter, to detach the blades from the windscreen. ) Any action on the wiper stalk in the minute after switching off the ignition places the blades vertically on the screen. ) To park the blades again, switch on the ignition and operate the wiper stalk.
VISIBILITY COURTESY LAMPS Map reading lamps ) With the ignition on, press the corresponding switch. Panoramic sunroof courtesy lamps 1. Front courtesy lamp 2. Map reading lamps Front courtesy lamp In this position, the courtesy lamp comes on gradually: - when the vehicle is unlocked, when a door or the boot is opened, when the key is removed from the ignition, when the remote control locking button is activated, in order to locate your vehicle.
VISIBILITY LIGHTING PACK Interior mood lighting This lighting, available once the sidelamps are on, in night mode, provides subdued lighting in the passenger compartment. Operation This back-lit control, located near the steering wheel below the dashboard, is used to switch on and off and adjust the brightness of this lighting. To increase brightness: ) Press the right of the control to obtain the desired level.
FITTINGS SLIDING SUN VISOR Sliding blinds The visors are fitted with a locking system on their central housing when the blind is reeled in. To remove the visor from its central housing or to reposition it, it must be in a vertical position. Child surveillance mirror Do not attach or suspend heavy objects on the slide rail of the sun blind. Sliding blinds are provided for your protection against bright sunlight. They can be adjusted manually. ) Slide the blind to the desired position by pushing at A.
FITTINGS VI UPPER STORAGE COMPARTMENTS ILLUMINATED GLOVE BOX COOLED GLOVE BOX There are large storage compartments at the top of the dashboard, one on the driver's side and one on the passenger's side. ) To open, press the button at the bottom corner. ) To close, lower the lid fully until it clicks. Its lid has areas for storing a pen, a pair of spectacles, tokens, cards, a can, fragrance cartridges... ) To open the glove box, raise the handle and lower the lid.
FITTINGS COOL STORAGE Vehicles with the electronic gearbox system or an automatic gearbox possess an additional storage space in the middle of the dashboard. ) To open, pull the handle and lower the lid. The cooled storage has automatic lighting. It can accommodate a 1.5 litre bottle and two 0.5 litre bottles, for example. Two cup-holders are available when the lid is open. The cooled storage has a ventilation nozzle.
FITTINGS MATS Removable carpet protection component. To avoid any risk of jamming of the pedals: - only use mats which are suited to the fixings already present in the vehicle; their use is essential, - never fit one mat on top of another. USB BOX VI Fitting When fitting the mat for the first time, on the driver's side, use only the fixings provided in the wallet attached. The other mats are simply placed on the carpet.
FITTINGS AIRCRAFT-STYLE REAR TABLES ) Pull the table downwards to open. ) To stow the table, raise it until the latch locks. For safety reasons, these tables collapse downwards if excessive pressure is exerted on them. SECOND ROW FOOTWELL Individual reading lamps Rear table stowed Rear table opened The backrests of the front seats are fitted with aircraft-style tables. These incorporate a cup-holder A and a retaining strap B, for the placing of objects.
FITTINGS THIRD ROW STORAGE SIDE BLINDS (GRAND C4 PICASSO) Third-row passengers may have storage pockets in the side panel and each of them will have a cupholder (7 seater model). Fitted on the 2nd and 3rd row rear windows, these protect young children from the sun's rays. Fitted on the 2nd row rear windows, these protect young children from the sun's rays. VI Second row ) Pull on the tab A and anchor the blind on the hooks B. 110 ) Pull on the tab and anchor the blind on the hooks.
FITTINGS LUGGAGE COVER (C4 PICASSO) This is in two parts. VI Rear parcel shelf Front parcel shelf Removal ) Unhook the cords. ) Push upwards, then lift on each side of the luggage cover. Removal ) First remove the rear shelf. ) Push upwards, then lift on each side. Fitting ) Offer up the shelf to its housings and push firmly down until it engages. ) For the shelf to rise with the tailgate, take the cords and attach them on the tailgate. Refitting ) Direct the flap downwards.
FITTINGS MODUBOX (C4 PICASSO) Use outside the vehicle Equipment for use both inside the vehicle and away from the vehicle. It comprises a shopping trolley and a flexible bag (insulated on some versions) which can be used independently of each other depending on your needs (by detaching the fastenings on each side at the top and bottom). LUGGAGE COVER ROLLER (GRAND C4 PICASSO) Position 1 5-seat configuration; installed behind the second-row seats, with the third-row seats folded away.
FITTINGS The roller has a moving flap to avoid interference with the secondrow passengers when the seats are in the "reclined" position. Position 2 7-seat configuration; installed behind the third-row seats when these are folded away. This position conceals objects stowed in the boot from outside view. ) Engage the lug on the left of the roller in notch C. ) Pass the right-hand end above the third-row armrest. ) Engage the lug in notch D. ) Pull the seat belt(s) so that they reel out without locking.
FITTINGS CARGO NET (GRAND C4 PICASSO) VI 114 This enables you to maximise the vehicle’s loadspace. It retains objects, preventing them from sliding towards the front of the passenger compartment. You insert it under the luggagecover roller securing it on the third-row side mouldings. Position 1 Position 2 5-seat configuration: installed behind the second row. 2-seat configuration; installed behind the first row.
FITTINGS LUGGAGE ANCHORING RINGS (C4 PICASSO) LUGGAGE ANCHORING RINGS (GRAND C4 PICASSO) LUGGAGE RETAINING NET (GRAND C4 PICASSO) Attached to the luggage anchoring rings, it allows objects to be held on the boot floor. For reasons of safety in the event of sudden braking, it is recommended that you place heavy objects on the floor as:m! close as possible to the backrests of the second-row seats.
FITTINGS TORCH This is a portable lamp, fitted in the boot wall, which can be used to illuminate the boot or as a torch. VI Grand C4 Picasso Boot lamp The boot lamp A comes on automatically when the boot is opened and switches off automatically when the boot is closed. Various lighting durations are available: ignition off, approximately ten minutes, - in energy economy mode, approximately thirty seconds, - engine running, no limit.
CHILD SAFETY GENERAL POINTS RELATING TO CHILD SEATS CHILD SEAT IN THE FRONT Although one of CITROËN's main criteria when designing your vehicle, the safety of your children also depends on you.
CHILD SAFETY Passenger airbag OFF Refer to the advice given on the label present on both sides of the passenger's sun visor. VII To assure the safety of your child, you must deactivate the passenger's front airbag when you install a child seat in the rearwards facing position on the front passenger's seat. Otherwise, there is a risk that the child could be seriously injured or killed if the airbag were deployed.
CHILD SAFETY CHILD SEATS RECOMMENDED BY CITROËN CITROËN offers a complete range of recommended child seats which are secured using a three point seat belt: Group 0+: from birth to 13 kg Groups 1, 2 and 3: from 9 to 36 kg L1 "RÖMER Baby-Safe Plus" Installed in the rearwards-facing position. L2 "KIDDY Comfort Pro" The impact shield must be used for carrying young children (from 9 to 18 kg).
CHILD SAFETY LOCATIONS FOR CHILD SEATS SECURED WITH THE VEHICLE SEAT BELT In conformity with European law, this table tells you to what extent each of the seat positions in your vehicle may take a child seat that is secured with the vehicle seat belt and approved as Universal (a), according to the weight of the child and the position in the vehicle.
CHILD SAFETY ADVICE ON CHILD SEATS The incorrect installation of a child seat in a vehicle compromises the child's protection in the event of an accident. When installing a child seat using the seat belt, check that the seat belt is tightened correctly on the child seat and that it secures the child seat firmly on the seat of your vehicle. Remember to fasten the seat belts or the child seat harnesses keeping the slack in relation to the child's body to a minimum, even for short journeys.
CHILD SAFETY "ISOFIX" MOUNTINGS There are three rings for each seat: Your vehicle has been approved in accordance with the latest ISOFIX regulations. The three second row seats are fitted with regulation ISOFIX mountings. ISOFIX child seats are fitted with two latches which are secured easily on the two rings A. Some also have an upper strap which is attached to the ring B. The incorrect installation of a child seat in a vehicle compromises the child's protection in the event of an accident.
CHILD SAFETY RÖMER Duo Plus ISOFIX (size category B1) Group 1: from 9 to 18 kg ) Installed only in the forwards-facing position. Fitted with an upper strap to be secured on the upper ring B, referred to as the TOP TETHER. Three seat body angles: sitting, reclining, lying. Adjust the front seat of the vehicle so that the child's feet do not touch the back of the seat. VII This child seat can also be used on seats which are not fitted with ISOFIX mountings.
CHILD SAFETY LOCATIONS FOR INSTALLING ISOFIX CHILD SEATS In compliance with European legislation (ECE 16), this table indicates which of the ISOFIX child seats can be installed in seat positions in your vehicle that are equipped with ISOFIX mounting points. For ISOFIX universal and semi-universal child seats, the ISOFIX size class, defined by a letter from A to G, is shown on the child seat to the right of the ISOFIX logo. Child weight/age given as a guide Less than 10 kg (group 0) Up to approx.
CHILD SAFETY MANUAL CHILD LOCK ELECTRIC CHILD LOCK Mechanical system to prevent opening of the rear door using its interior control. The control is located on the edge of each rear door. Remote control system to prevent opening of the rear doors using their interior controls and use of the rear electric windows. Locking ) Using the ignition key, turn the red control one eighth of a turn, following the instructions on the label.
SAFETY VIII DIRECTION INDICATORS HAZARD WARNING LAMPS Horn Selection of the left or right direction indicators to signal a change of direction of the vehicle. A visual warning by means of the direction indicators to alert other road users to a vehicle breakdown, towing or accident. Audible warning system to alert other road users to an imminent danger. ) Left: lower the lighting stalk beyond the point of resistance. ) Right: raise the lighting stalk beyond the point of resistance.
SAFETY TYRE UNDER-INFLATION DETECTION Sensors fitted in each valve check the tyre pressure during driving and trigger a warning in the event of malfunction (speed above 12 mph (20 km/h)). Puncture The STOP warning lamp comes on in the instrument panel, accompanied by an audible signal and a message on the multifunction screen locating the wheel concerned. Stop immediately, avoiding any sudden movement of the steering wheel and the brakes.
SAFETY BRAKING ASSISTANCE SYSTEMS Operating fault Group of supplementary systems which help you to obtain optimum braking in complete safety in emergency situations: - anti-lock braking system (ABS), - electronic brake force distribution (EBFD), - emergency braking assistance (EBA). If this warning lamp comes on, accompanied by an audible signal and a message in the screen, it indicates a malfunction of the anti-lock braking system which could result in loss of control of the vehicle when braking.
SAFETY TRAJECTORY CONTROL SYSTEMS Anti-slip regulation (ASR) and electronic stability programme (ESP) The anti-slip regulation (also known as Traction Control) optimises traction to prevent skidding of the wheels, by acting on the brakes of the driving wheels and on the engine. The electronic stability programme acts on the brake of one or more wheels and on the engine to keep the vehicle on the trajectory required by the driver, within the limits of the laws of physics.
SAFETY Reactivation These systems are reactivated automatically each time the ignition is switched back on or from 30 mph (50 km/h). ) Press the "ESP OFF" button again to reactivate them manually. Operating fault If this warning lamp comes on, accompanied by an audible signal and a message in the multifunction screen, this indicates a malfunction of these systems. Have it checked by a CITROËN dealer or a qualified workshop.
SAFETY SEAT BELTS The pretensioning seat belts are active when the ignition is on. The force limiter reduces the pressure of the seat belt against the chest of the occupant, so increasing his protection. Height adjustment Fastening Front seat belts The front seat belts are fitted with a pretensioning system and force limiter. This system improves safety in the front seats in the event of a front impact.
SAFETY Centre rear seat belt Using the seat belt (C4 Picasso) VIII 132 ) Open the cover A. ) Remove the belt tongues from their housing. ) Bring the belt tongues up to the relay ring B. ) Insert the attachment, then pass the tongues through the ring. ) Close the cover A. Make sure that the belt is correctly positioned in the recess in the cover provided for this purpose.
SAFETY Third row rear seat belts (Grand C4 Picasso) Before use: To avoid damaging or jamming the seat belts, stow them carefully on the sides of the seat backrests. Instructions for use of the third row passenger seat belts Stowing the tongue of the third-row seat belt Take care to attach the third-row passenger seat belts securely to the rings provided for this purpose. Do not attach the belts to the luggage anchoring rings marked with a red cross, as shown in the illustration.
SAFETY VIII 134 The driver must ensure that passengers use the seat belts correctly and that they are all restrained securely before setting off. Wherever you are seated in the vehicle, always fasten your seat belt, even for short journeys. Do not interchange the seat belt buckles as they will not fulfil their role fully. The seat belts are fitted with an inertia reel permitting automatic adjustment of the length of the strap to your size. The seat belt is stowed automatically when not in use.
SAFETY AIRBAGS System designed to maximise the safety of the occupants (with the exception of the rear centre passenger) in the event of violent collisions. It supplements the action of the force-limiting seat belts.
SAFETY Deactivation Activation When you remove the child seat, turn switch 1 to the "ON" position to reactivate the airbag and so ensure the safety of your front passenger in the event of an impact. Operating fault VIII Only the front passenger's airbag can be deactivated: ) with the ignition off, insert the key in the passenger airbag deactivation switch 1, ) turn it to the "OFF" position, ) then, remove the key keeping the switch in this position.
SAFETY Lateral airbags* Impact detection zones System which protects the driver and front passenger in the event of a serious side impact in order to limit the risk of injury to the chest. Each lateral airbag is fitted in the front seat back frame, on the door side. A. Front impact zone. B. Side impact zone.
SAFETY For the airbags to be fully effective, observe the following safety rules: VIII 138 Sit in a normal upright position. Wear a correctly adjusted seat belt. Do not leave anything between the occupants and the airbags (a child, pet, object...). This could hamper the operation of the airbags or injure the occupants. After an accident or if the vehicle has been stolen or broken into, have the airbag systems checked.
DRIVING ELECTRIC PARKING BRAKE Manual application Manual release With the vehicle stationary, to apply the parking brake whether the engine is running or not, pull control lever A. The application of the parking brake is confirmed by: With the ignition on or the engine running, to release the parking brake, press on the brake pedal, or the accelerator, pull then release control lever A.
DRIVING Maximum application If necessary, you can use maximum application of the parking brake. It is obtained by means of a long pull on control lever A, until you see the message "Parking brake on" and an audible signal is heard. Maximum application is essential: - when towing a caravan or a trailer, if the automatic functions are activated but you are applying the parking brake manually, - when the gradient you are parked on is variable in its effect (e.g.
DRIVING To immobilise the vehicle, engine running Activation/Deactivation of the automatic functions* To immobilise the vehicle when stationary with the engine running, you must apply the parking brake manually by pulling on control lever A. The automatic application when the engine is switched off and the automatic release when you press the accelerator can be deactivated. Activation/deactivation is performed using the configuration menu of the multifunction screen.
DRIVING Dynamic emergency braking If a failure of the ESP system is signalled by the illumination of this warning lamp, then braking stability is not guaranteed. In this event, stability must be assured by the driver by repeating alternate "pull-release" actions on control lever A. The dynamic emergency braking must only be used in exceptional circumstances. IX 142 In the event of a failure of the vehicle’s main braking system or in an exceptional situation (e.g.
DRIVING Emergency release In the event of a malfunction of the electric parking brake or the battery running flat, an emergency mechanism can release the parking brake. ) Immobilise the vehicle, with the engine running, by engaging first gear (manual gearbox), position P (automatic gearbox) or M or R (6-speed electronic gearbox system). ) Switch off the engine, but leave the ignition on.
DRIVING Operating faults If any of these instances arises, contact a CITROËN dealer or a qualified workshop as soon as possible. SITUATION CONSEQUENCES Electric parking brake fault and display of If the electric parking brake fault warning lamp and the service message "Parking brake faulty" and the fol- warning lamp come on, position the vehicle in a safe location (on lowing warning lamps: flat ground, with a gear engaged).
DRIVING SITUATION Display of message "Parking brake faulty" and the following warning lamps: CONSEQUENCES To ) ) ) 4 and/or flashing To ) ) Display of message "Parking brake control faulty – auto parking brake activated" and the following warning lamps: - The automatic functions are deactivated. Hill start assist is not available. apply the electric parking brake: Immobilise the vehicle and switch off the ignition Pull the control lever for at least 5 seconds or until maximum application.
DRIVING HILL START ASSIST System which holds your vehicle temporarily (approximately 2 seconds) when starting on a slope, the time it takes to move your foot from the brake pedal to the accelerator pedal. This function is only active when: - the vehicle is completely stationary, with your foot on the brake pedal, - in particular conditions on a slope, - with the driver’s door closed. The hill start assist cannot be deactivated.
DRIVING 5-SPEED MANUAL GEARBOX Engaging reverse gear ) Move the gear lever to the right then back. Only engage reverse gear when the vehicle is stationary with the engine at idle. Starting the vehicle ) Check that the gear lever is in neutral. ) Do not touch the accelerator. ) For Diesel engines: turn the key to position M and wait until the pre-heating warning lamp switches off if it has come on. ) Operate the starter, turning the key until the engine starts (no more than ten seconds).
DRIVING GEAR EFFICIENCY INDICATOR* System which reduces fuel consumption by advising the driver to change up on vehicles fitted with a manual gearbox. Operation IX 148 The system intervenes only when driving economically. Depending on the driving situation and your vehicle's equipment, the system may advise you to skip one or more gears. You can follow this instruction without engaging the intermediate gears. The gear recommended should not be considered compulsory.
DRIVING 6-SPEED ELECTRONIC GEARBOX SYSTEM The 6-speed electronic gearbox offers a choice between the comfort of fully automatic operation or the driving pleasure of manual gear changing. You have a choice of two driving modes: - automatic mode for automatic control of the gears by the gearbox, - manual mode for sequential changing of the gears by the driver. Displays in the instrument panel - Mode selection - ) Automated mode: gear lever 2 in position A. ) Manual mode: gear lever 2 in position M.
DRIVING Reverse gear To engage reverse, the vehicle must be immobilised with your foot on the brake pedal. Automatic mode Operation in automatic mode ) Move the gear lever to A. ) Move the gear lever to R. At low speeds, if reverse is selected, the N indicator flashes and the gearbox goes into neutral automatically. To engage reverse, put the gear lever in position N, then in position R. Manual mode ) Move the gear lever to M. ) Pull the "+" paddle to change up a gear.
DRIVING Temporary manual operation when in automatic mode By pulling either of the "+" or "-" paddles, you can exercise temporary control over the gearbox. The request to change gear will be taken into account. You will still be in automatic mode. The warning lamp A remains on in the instrument panel. This function enables you to anticipate certain situations such as the approach of a bend or the need to overtake another vehicle. Operation in manual mode ) Move the gear lever to position M.
DRIVING The paddles cannot be used to select neutral or reverse gear, or to exit reverse gear. - If the vehicle stops or reduces speed (for example when approaching a stop sign), the gearbox changes down automatically, to first gear if needed. - In manual mode, it is not necessary to release the accelerator completely during gear changes. - A request to change gear is accepted only if the engine speed permits it.
DRIVING The Stop & Start system puts the engine temporarily into standby - STOP mode - during stops in the traffic (red lights, traffic jams, or other...). The engine restarts automatically START mode - as soon as you want to move off. The restart takes place instantly, quickly and silently. Perfect for urban use, the Stop & Start system reduces fuel consumption and exhaust emissions as well as the noise level when stationary.
DRIVING Going into engine START mode - IX The "ECO" warning lamp goes off and the engine starts with the electronic gearbox system: gear lever in position A or M, release the brake pedal, or gear lever in position N and the brake pedal released, move the gear lever to position A or M, or engage reverse gear.
DRIVING Operating fault Maintenance Before doing anything under the bonnet, deactivate the Stop & Start system to avoid any risk of injury resulting from automatic operation of START mode. In the event of a fault with the system, the "ECO OFF" switch warning lamp flashes then comes on continuously. Have it checked by a CITROËN dealer or a qualified workshop. In the event of a fault in STOP mode, the vehicle may stall.
DRIVING AUTOMATIC GEARBOX Automatic gearbox which offers a choice between the ease of fully automatic operation or the driving pleasure of manual gear changing. There is a choice of two driving modes: - automatic operation for electronic control of the gears by the gearbox, - manual operation for sequential changing of the gears by the driver. Mode selection IX ) Automatic mode: gear lever 1 in position D, ) Manual mode: gear lever 1 in position M.
DRIVING Moving off To avoid any difference between the position of the gear lever and the true position of the gearbox, always come out of position P with the ignition on and your foot on the brake. Foot on the brake ) When this warning lamp comes on in the instrument panel, press the brake pedal to disengage the gear lever from position P. ) To start the engine, press the brake pedal and place the gear lever in position P. ) Operate the starter.
DRIVING Automatic operation Position of the gear lever for automatic gear changing. IX 158 ) Move the gear lever to position D. The gearbox constantly selects the gear that is best suited to the following conditions: - driving style, - road profile, - vehicle load. The gearbox is then operating in auto-adaptive mode, without requiring any intervention on your part.
DRIVING Manual operation - - Position of the gear lever for manual gear changing. ) Move the gear lever to position M. ) Pull the "+" paddle to change up a gear. ) Pull the "-" paddle to change down a gear. - If the vehicle stops or reduces speed (for example when approaching a stop sign), the gearbox changes down automatically to first gear. - In manual mode, it is not necessary to release the accelerator during gear changes. - A request to change gear is accepted only if the engine speed permits it.
DRIVING FIXED CENTRED CONTROLS STEERING WHEEL Cruise control/speed limiter and parking sensor controls 1. Activation of the parking sensors function. 2. Selection of cruise control or speed limiter. 3. Activation/Deactivation of speed limiter. Deactivation/Reactivation of cruise control. 4. Increase speed/Activation of cruise control. 5. Decrease speed/Activation of cruise control. IX 160 Audio system controls A. Volume decrease. B. Volume increase. C. Search of higher frequencies. D.
DRIVING Optional function controls Multifunction screen controls 1. Call/Hang up the telephone (see "Audio and Telematics" section). 2. Rheostat for dashboard lighting. 3. Start of voice recognition (see "Audio and Telematics" section). 4. Personalisation button: - courtesy lamp on/off or - diagnostics Press this button for more than two seconds to display the personalisation menu. 5. Air recirculation. A.
DRIVING SPEED LIMITER System which prevents the vehicle from exceeding the speed programmed by the driver. Once the limit speed has been reached, the accelerator pedal no longer has any effect. The speed limiter is switched on manually: a speed of at least 20 mph (approximately 30 km/h) must be programmed. Displays in the instrument panel The programmed information is grouped together in zone A of the instrument panel screen.
DRIVING Deactivation Press on button 3. This action information appear on ment panel causes the "OFF" to the instruscreen. This action does not cancel the memorised maximum speed which remains displayed in zone A of the instrument panel. If during the operation of the speed limiter, the system is unable to keep within the maximum speed (for example on a steep descent or under heavy acceleration) then the speed flashes. Adapt your speed as necessary.
DRIVING CRUISE CONTROL System which automatically maintains the vehicle speed programmed by the driver, without any action on the accelerator pedal. The cruise control is switched on manually: the vehicle speed must be at least 25 mph (approximately 40 km/h) and you must engage: - fourth gear on a manual gearbox, - second gear, in manual mode, on an electronic or automatic gearbox, - position A on an electronic gearbox or D on an automatic gearbox.
DRIVING Reactivation ) By recall of the memorised speed After a disengagement, press on button 3. Your vehicle automatically returns to the memorised cruise speed which is displayed in zone A. If the memorised cruise speed is higher than the current speed, the vehicle will accelerate to reach the former. ) By selection of the current speed Press on button 2 or 4 once the desired speed has been reached. The information "OFF" will then disappear from the instrument panel display.
DRIVING PARKING SPACE SENSORS IX After measuring the parking space available between two vehicles or obstacles, this system gives you information on: - the possibility of fitting into a free space, depending on the dimensions of your vehicle and the distances needed for manoeuvring, - the level of difficulty of the manoeuvre to be performed. The system does not measure spaces which are clearly much smaller or larger than the size of the vehicle.
DRIVING Operation You have identified a parking space: ) Press button A to activate the function. ) Activate the direction indicator on the side where the space is to be measured. ) During the measuring, go forward the length of the space, at a speed less than 12 mph (approximately 20 km/h), to prepare for your manoeuvre. The system then measures the size of the space.
DRIVING LANE DEPARTURE WARNING SYSTEM System which detects the involuntary crossing of longitudinal traffic lane markings on the ground (solid or broken line). Sensors, fitted below the front bumper, trigger a warning if the vehicle drifts over a lane marking (speed higher than 50 mph (80 km/h)). Activation Operating fault ) Press this button, the indicator lamp comes on. In the event of a malfunction, the service warning lamp comes on, accompanied by an audible signal and a message in the screen.
DRIVING PARKING SENSORS Rear parking sensors This system indicates the proximity of an obstacle (person, vehicle, tree, gate, etc.) which comes within the field of detection of sensors located in the bumper. Certain types of obstacle (stake, roadworks cone, etc.) detected initially will no longer be detected at the end of the manoeuvre due to the presence of blind spots. The system is switched on by engaging reverse gear. This is accompanied by an audible signal.
DRIVING Front parking sensors In addition to the rear parking sensors, the front parking sensors are triggered when an obstacle is detected in front and the speed of the vehicle is still below 6 mph (10 km/h). The front parking sensors are interrupted if the vehicle stops for more than three seconds in forward gear, if no further obstacles are detected or when the speed of the vehicle exceeds 6 mph (10 km/h).
DRIVING PNEUMATIC SUSPENSION Operation - Grand C4 Picasso C4 Picasso The pneumatic rear suspension enhances driving comfort by maintaining a constant body height whatever the vehicle load. If there is an increase in vehicle load, a sinking of the rear of the vehicle is detected and the pneumatic springs inflate in order to compensate for the extra weight.
DRIVING Loading/unloading assistance Grand C4 Picasso IX C4 Picasso The pneumatic suspension has an additional function: the possibility to raise or lower the height of the rear of the vehicle when stationary, in order to facilitate loading/unloading of the boot. Increasing the height of the boot floor ) Press continuously the top control A, which is located in the boot, on the left-hand side. This action will be accompanied by an audible signal.
CHECKS PARTNERS IN PERFORMANCE AND PROTECTING THE ENVIRONMENT Innovation in the search for performance For over 40 year, the TOTAL Research and Development departments have developed for CITROËN, lubricants to match the latest technical innovations on CITROËN vehicles, both for competition and for everyday motoring. For you, this is an assurance that you will obtain of the best performance for your engine.
CHECKS Opening Before doing anything under the bonnet, switch off the Stop & Start system to avoid any risk of injury resulting from an automatic change to START mode. ) At the front of the bonnet, push the exterior safety catch B to the left and raise the bonnet. The location of the interior release lever prevents opening of the bonnet while the left hand door is closed. This operation must only be carried out when the vehicle is stationary. Avoid opening the bonnet in strong winds.
CHECKS BLEEDING THE DIESEL FUEL FILTER Protective cover Removal ) Remove the protective cover by unclipping first point 1, then 3 and 4. ) Unclip point 2 pulling towards you, then lift. Refitting ) Clip point 2 first. ) Lower the cover, centring it. ) Clip points 1 and 4, pushing vertically and slightly rearwards. ) Clip point 3, pushing vertically. Bleeding water from the fuel filter Bleed the filter regularly (at every oil change).
CHECKS Priming the fuel system RUNNING OUT OF FUEL (DIESEL) 1.6 litre HDi engine 2.0 litre HDi engine Detach the protective cover for access to the priming pump. Detach the protective cover for access to the priming pump. In the event of running out of fuel: ) after filling (minimum 5 litres), squeeze the manual priming pump repeatedly, until some resistance is felt, ) then operate the starter, gently pressing the accelerator until the engine starts.
CHECKS PETROL ENGINES X The covers and caps provide access for checking the levels of the various fluids and for replacing certain components. 1. Power steering fluid reservoir. 2. Screenwash and headlamp wash reservoir. 3. Coolant header tank. 4. Air filter. 5. Brake fluid reservoir. 6. Battery/Fuses. 7. Fusebox. 8. Engine oil filler cap. 9. Engine oil dipstick.
CHECKS X DIESEL ENGINES The covers and caps provide access for checking the levels of the various fluids, for replacing certain components and for priming the fuel system. 1. Power steering fluid reservoir. 2. Screenwash and headlamp wash reservoir. 3. Coolant header tank 4. Brake fluid reservoir. 5. Battery/Fuses. 178 6. Fusebox. 7. Air filter. 8. Engine oil filler cap. 9. Engine oil dipstick. 10. Priming pump*. 11. Bleed screw*.
CHECKS Brake fluid level CHECKING LEVELS If a level drops significantly, have the corresponding system checked by a CITROËN dealer or a qualified workshop. Check all of these levels regularly and top them up if necessary, unless otherwise indicated. After topping up the oil, the check when switching on the ignition with the oil level indicator in the instrument panel is not valid during the 30 minutes after topping up. The brake fluid level should be close to the "MAX" mark.
CHECKS X Coolant level Screenwash and headlamp wash fluid The coolant level should be close to the "MAX" mark but should never exceed it. When the engine is warm, the temperature of the coolant is regulated by the fan. This can operate with the ignition off. On vehicles which are fitted with a particle emission filter, the fan may operate after the vehicle has been switched off, even if the engine is cold.
CHECKS CHECKS Unless otherwise indicated, check these components in accordance with the servicing booklet and according to your engine. Otherwise, have them checked by a CITROËN dealer or a qualified workshop. 12 V battery The battery does not require any maintenance. However, check that the terminals are clean and correctly tightened, particularly in summer and winter.
CHECKS Manual gearbox The gearbox does not require any maintenance (no oil change). Refer to the servicing booklet for the details of the level checking interval for this component. 6-speed electronic gearbox system The gearbox does not require any maintenance (no oil change). Refer to the servicing booklet for details of the checking interval for this component. Automatic gearbox X The gearbox does not require any maintenance (no oil change).
P R A C T I C A L I N F O R M AT I O N TEMPORARY PUNCTURE REPAIR KIT Complete system consisting of a compressor and a sealant cartridge which permits temporary repair of a tyre so that you can drive to the nearest garage. Using the kit ) Tick the wheel to be repaired on the speed limitation sticker enclosed then affix the sticker to the vehicle's steering wheel to remind you that a wheel is in temporary use. ) Switch off the ignition. ) Clip the cartridge 1 on the compressor 2.
P R A C T I C A L I N F O R M AT I O N ) Switch on the compressor by moving the switch A to position "1" until the tyre pressure reaches 2.0 bars. ) Remove the compressor and store the cartridge in the plastic bag, supplied in the kit, to avoid staining your vehicle with traces of fluid. ) Drive immediately for approximately two miles (three kilometres), at reduced speed (between 15 and 35 mph - 20 and 60 km/h), to plug the puncture. ) Stop to check the repair and the pressure.
P R A C T I C A L I N F O R M AT I O N ) Connect the compressor's electric plug to the vehicle's 12 V socket again. ) Start the vehicle again and leave the engine running.
P R A C T I C A L I N F O R M AT I O N CHANGING A WHEEL Access to the tools Depending on equipment, the tools are to be found either in the compartment under the second-row passenger footwells (the compartment is opened by turning the screw a quarter turn) or in the well under the third-row left-hand seat. XI 186 1. Tool for removing the central trim on alloy wheels* or 2. Tool for removing the chrome covers on the wheel bolts on alloy wheels* 3. Centring guide* 4. Wheelbrace 5.
P R A C T I C A L I N F O R M AT I O N Access to the spare wheel C4 Picasso Grand C4 Picasso Taking out the wheel (C4 Picasso) ) Lift the boot floor covering to reveal the spare wheel carrier drive on the left. ) Take the extension 7 from the set of tools. ) Lift up the spare wheel carrier drive aperture cap, if fitted. ) Fit the extension to the drive then engage the head of the wheelbrace 4 on the extension.
P R A C T I C A L I N F O R M AT I O N Removing a wheel XI ) Park the vehicle on level, stable and non-slippery ground. Apply the parking brake (a message and a warning lamp appear in the instrument panel). Switch off the ignition and engage first gear or reverse gear depending on the slope (position P if an automatic gearbox, D or R if a 6-speed electronic gearbox). ) Use a chock to secure the vehicle more safely. Place the chock 9 in front of the wheel opposite the punctured wheel.
P R A C T I C A L I N F O R M AT I O N Wheel for temporary use If your vehicle is equipped with a spare wheel for temporary use only, when fitting this it is normal to observe that the wheel bolts do not come to bear directly on the wheel rim. The spare wheel is secured by the conical section of each wheel bolt. When refitting the original wheel, ensure that the wheel bolts and washers are clean and in good condition. Fitting a wheel ) Position the wheel with the aid of the centring guide 3.
P R A C T I C A L I N F O R M AT I O N CHANGING A BULB Front lamps Model with halogen headlamps Model with Xenon headlamps and directional headlamps 1. Dipped beam headlamps (H7-55 W) 2. Main beam headlamps (H1-55 W) 3. Sidelamps (H6W-6 W) Daytime running lamps/ sidelamps (LEDs) 4. Direction indicators (H21-21 W) 1. Dual-function Xenon headlamps (dipped/main beam) 2. Additional main beams (H7-55W) 3. Sidelamps (H6W-6W) Daytime running lamps/ sidelamps (LEDs) 4.
P R A C T I C A L I N F O R M AT I O N Dual-function Xenon headlamps (dipped/main beam) Dipped beam headlamps Main beam headlamps ) Remove the rubber cover. ) Rotate the bulb-holder a quarter turn anti-clockwise and remove it from its housing. ) Replace the faulty bulb. ) Reposition the bulb-holder by pushing it in, tightening it by a quarter turn clockwise. ) Refit the rubber cover. ) Remove the rubber cover. ) Detach the clips by lowering them on each side of the bulb.
P R A C T I C A L I N F O R M AT I O N XI 192 Sidelamps Direction indicators Integrated direction indicator side repeaters ) Rotate the bulb-holder a quarter turn anti-clockwise. ) Remove it from its housing. ) Replace the faulty bulb. ) Reposition the bulb-holder. ) Rotate it a quarter turn clockwise to reposition in its housing. The direction indicator bulb is located underneath the main beam bulb. ) Remove the rubber cover. ) Pull on the bulb-holder to remove it. ) Replace the faulty bulb.
P R A C T I C A L I N F O R M AT I O N Changing daytime running lamps/sidelamps (LEDs) Front foglamps (H11-55 W) Rear foglamp (P21 W) For the replacement of this type of LED lamp, contact a CITROËN dealer or a qualified workshop. ) Insert the key in the notch A, tilting the bulb-holder cover, located underneath the bumper, then insert the key in the notch B to remove it. ) Undo the lamp. ) Tilt the bulb-holder. ) Change the faulty bulb. ) Reposition the bulb-holder.
P R A C T I C A L I N F O R M AT I O N Rear lamps (C4 Picasso) Lamps mounted on the bodywork ) Refit the lamp unit on the body and do up the two screws. ) Reposition the plastic cover by pressing on it. Lamps mounted on the tailgate 1. Direction indicators (PY21W) 2. Brake lamps/sidelamps (P21/5W) 3. Reversing lamp (P21W) XI 194 ) Identify the faulty bulb. ) With the boot open, press on the plastic cover A, located close to the lamp unit, to release it from its housing.
P R A C T I C A L I N F O R M AT I O N Rear lamps (Grand C4 Picasso) 1. 2. 3. 4. Direction indicators (PY21W) Brake lamps (P21W) Reversing lamp (P21W) Sidelamps (LEDs) For this type of lamp, contact a CITROËN dealer or qualified workshop. Changing bulbs ) Identify the faulty bulb. ) With the tailgate open, undo the 3 screws located on the side of the lamp unit and pull it rearwards to detach. ) Disconnect the connector linking the lamp unit to the boot. Do not disconnect the LEDs. ) Remove the seal.
P R A C T I C A L I N F O R M AT I O N Third brake lamp with bulb (W5W) ) With the boot open, detach the interior trim. ) Undo the nuts. ) Using a thin screwdriver, detach the 3 retaining lugs. ) Remove the lamp via the exterior of the tailgate. ) Remove the bulb-holder. ) Change the faulty bulb(s). To refit, carry out these operations in reverse order. Third brake lamp (LEDs) Interior lighting Boot lamps (W5W) Interior lamp (1/W5W) Detach the unit by pushing it rearwards.
P R A C T I C A L I N F O R M AT I O N CHANGING A FUSE Before replacing a fuse: - the cause of the failure must be identified and rectified, - all electrical consumers must be switched off, - your vehicle must be stationary with the engine off. Identify the failed fuse by reference to the tables and layout drawings below. Changing a fuse ) Use the special tweezer A to remove the fuse from its housing and check the condition of the filament.
P R A C T I C A L I N F O R M AT I O N Fuses under the dashboard Access to the fuses ) Open the glove box. ) Undo the screw by a quarter turn and pivot the housing.
P R A C T I C A L I N F O R M AT I O N Access to the second dashboard fusebox After any operation on the fuses in the fusebox, check that the fusebox cover is put back correctly for their protection.
P R A C T I C A L I N F O R M AT I O N Fuses in the engine compartment Access to the fuses ) Detach and remove the cover. After any operation, refit the cover carefully. If the cover is not correctly positioned or not properly closed, this could cause serious problems on your vehicle. For the same reason, take care not to spill any liquid in the fusebox.
P R A C T I C A L I N F O R M AT I O N Table of fuses Fuse N° Rating F1 20 A Functions Engine management F2 15 A Horn F3 10 A Screenwash pump F4 20 A Headlamp wash pump F5 15 A Engine components F6 10 A Xenon dual-function directional headlamps, automatic headlamp height adjustment, clutch switch, protection switch box (BCP) F7 10 A Automatic gearbox, engine coolant level switch, power steering F8 25 A Starter motor F9 10 A Stoplamp switch F10 30 A Engine components F11 40 A
P R A C T I C A L I N F O R M AT I O N Fuses on the battery After any operation, carefully reclose the cover. If the cover is not correctly positioned or not properly closed, this could cause serious problems on your vehicle. For the same reason, take care not to spill any liquid in the fusebox. Access to the fuses ) Detach and remove the cover. Fuses F1 to F6 are located on the small board, clipped vertically on the battery fusebox. Fuses F7 to F12 are midifuses.
P R A C T I C A L I N F O R M AT I O N 12 V BATTERY Access to the battery Procedure for starting the engine using another battery or for charging your flat battery. The presence of this label, in particular with the Stop & Start system, indicates the use of a 12 V lead-acid battery with special technology and specification; the involvement of a CITROËN dealer or a qualified workshop is essential when replacing or disconnecting the battery.
P R A C T I C A L I N F O R M AT I O N Disconnecting the (+) terminal Starting using another battery If the battery in your vehicle is flat, the engine can be started using a slave battery (external or in another vehicle) and jump leads. First ensure that the slave battery has a nominal voltage of 12 V and a capacity at least equal to that of the flat battery. Do not try to start the engine by connecting a battery charger. Do not disconnect the (+) terminal when the engine is running.
P R A C T I C A L I N F O R M AT I O N Charging the battery using a battery charger If the battery of your vehicle is flat or prior to taking the vehicle out of service for an extended period, you can charge the battery using a battery charger. For information on the specification of battery chargers compatible with your battery, refer to a CITROËN dealer or a qualified workshop. Before disconnecting ) Go to the battery. ) Check that all of the openings doors, boot... - are closed but not locked.
P R A C T I C A L I N F O R M AT I O N ENERGY ECONOMY MODE Switching to economy mode Exiting economy mode System which manages the duration of use of certain functions to conserve a sufficient level of charge in the battery. After the engine has stopped, you can still use functions such as the audio and telematics system, windscreen wipers, dipped beam headlamps, courtesy lamps, etc. for a maximum combined duration of thirty minutes.
P R A C T I C A L I N F O R M AT I O N TOWING THE VEHICLE Towing your vehicle Towing another vehicle ) On the front bumper, unclip the cover by pressing at the top left and pulling at the right. ) Screw the towing eye in fully. ) Install the towing bar. ) Switch on the hazard warning lamps on the towed vehicle. ) Place the gear lever in neutral (position N on the electronic gearbox or automatic gearbox). ) On the rear bumper, unclip the cover by pressing at the bottom at pulling at the top.
P R A C T I C A L I N F O R M AT I O N General recommendations Observe the legislation in force in your country. Ensure that the weight of the towing vehicle is higher than that of the towed vehicle. The driver must stay at the wheel of the towed vehicle. Driving on motorways and fast roads is prohibited when towing. When towing a vehicle with all four wheels on the ground, always use an approved towing bar; rope and straps are prohibited.
P R A C T I C A L I N F O R M AT I O N Driving with a trailer places greater demands on the towing vehicle and the driver must take particular care. Towbar suitable for the attachment of a trailer with additional lighting and signalling. Your vehicle is primarily designed for transporting people and luggage, but it may also be used for towing a trailer.
P R A C T I C A L I N F O R M AT I O N ROOF BARS For your safety and to avoid damage to the roof and tailgate, the design of your vehicle requires the use of roof bars and roof boxes that are tested and approved by CITROËN. Regardless of the type of load carrier to be mounted on the roof (roof box, bicycle carrier, ski carrier...), you must fit transverse roof bars. Maximum load, distributed over the roof bars (for a loading height not exceeding 40 cm, except bicycle carrier): 80 kg.
P R A C T I C A L I N F O R M AT I O N ACCESSORIES A wide range of accessories and genuine parts is available from the CITROËN dealer network. These accessories and parts have been tested and approved for reliability and safety. They are all adapted to your vehicle and benefit from CITROËN's recommendation and warranty. "Comfort": front and rear parking sensors, isotherm module, rechargeable torch, sun blinds, air deflector, fragrance cartridges...
P R A C T I C A L I N F O R M AT I O N XI 212 "Multimedia": Bluetooth® hands-free system, audio systems, portable satellite navigation system, DVD player, USB Box, speakers, 230 V/50 Hz socket, 230 V/12 V power supply adaptor, WiFi on board... You can also obtain products for cleaning and maintenance (exterior and interior), topping up (screenwash...) and replacement cartridges (for the temporary puncture repair kit...) from the CITROËN dealer network.
T E C H N I C A L D ATA MODELS: Model codes: UA... UE... UD... ENGINES AND GEARBOXES 5FS-0 5FS-0/CU1 5FV-8/P 5FV-8/PCU1 RFJ-F PETROL ENGINES VTi 120 THP 155 VTi 143 Cubic capacity (cc) 1 598 1 598 1 997 Bore x stroke (mm) 77 x 85.8 77 x 85.
T E C H N I C A L D ATA WEIGHTS AND TOWED LOADS (in kg) Petrol engines VTi 120 THP 155 VTi 143 Automatic Electronic gearbox system Automatic 5FS-0 5FV-8/P RFJ-F Unladen weight 1 430 - 1 415 - 1 415 1 517 - 1 430 - 1 430 1 600 - 1 556 - 1 552 1 505 - 1 490 - 1 490 1 592 - 1 505 - 1 505 1 675 - 1 631 - 1 627 770 - 700 - 525 703 - 630 - 610 660 - 514 - 538 2 200 - 2 115 - 2 015 2 220 - 2 060 - 2 040 2 260 - 2 070 - 2 090 3 300 - 3 315 - 3 315 3 420 - 3 410 - 3 390 3 660 - 3 570 - 3 590
T E C H N I C A L D ATA MODELS: Model codes: UA... UE... UD... DIESEL ENGINES ENGINES AND GEARBOXES 9HZ-C 9HZ-C/ CU1 9HZ-H/P 9HZ-H/ PCU1 9HR-8 9HR-8/ CU1 HDi 110 9HR-8/P 9HR-8/ PCU1 9HR-8/PS RHJ-H/P RHJ-H/ PCU1 HDi 110 RHR-J HDi 138 Cubic capacity (cc) 1 560 1 560 1 997 Bore x stroke (mm) 75 x 88.3 75 x 88.
T E C H N I C A L D ATA MODELS: Model codes: UA... UE... UD...
T E C H N I C A L D ATA WEIGHTS AND TOWED LOADS (in kg) Diesel engines Gearboxes Model codes: UA... UE... UD...
T E C H N I C A L D ATA WEIGHTS AND TOWED LOADS (in kg) Diesel engines Gearboxes Model codes: UA... UE... UD...
T E C H N I C A L D ATA WEIGHTS AND TOWED LOADS (in kg) Diesel engines Gearboxes Model codes: UA... UE... UD...
T E C H N I C A L D ATA WEIGHTS AND TOWED LOADS (in kg) Diesel engines Manual Electronic gearbox system Automatic Type codes: UA... UE... UD...
T E C H N I C A L D ATA WEIGHTS AND TOWED LOADS (in kg)- COMMERCIAL VERSIONS Petrol engines Gearboxes Model codes: UA... UD...
T E C H N I C A L D ATA WEIGHTS AND TOWED LOADS (in kg) - COMMERCIAL VERSIONS Diesel engines HDi 138 HDi 150 Model codes: UA... UD...
T E C H N I C A L D ATA DIMENSIONS (IN METRES) Exterior (CITROËN Grand C4 Picasso and CITROËN C4 Picasso) CITROËN Grand C4 Picasso CITROËN C4 Picasso A 2.730 2.730 B 4.590 4.470 C 0.990 0.990 D 0.870 0.750 E 1.510 1.510 F 1.540 1.540 G* 1.660 to 1.710 1.660 to 1.680 H 2.100 2.100 I 1.830 1.830 * Depending on suspension and roof bars.
T E C H N I C A L D ATA Interior (CITROËN C4 Picasso) XII 224 A 0.930 E 0.930 B 0.960/0.980 F 1.140 C 0.880/1.000 G 1.120 D 1.610/1.870 H 1.
T E C H N I C A L D ATA Interior (CITROËN Grand C4 Picasso) A 0.920 E 0.880 B 0.990/1.000 F 1.070 C 1.030/1.160 G 1.160 D 1.800/2.060 H 1.
T E C H N I C A L D ATA IDENTIFICATION MARKINGS Various visible markings for identification of the vehicle. The vehicle type and the identification number are also indicated on the registration document. All CITROËN original replacement parts are available exclusively within the dealer network. For your safety and in order to remain within the terms of the warranty, you are advised to use only CITROËN replacement parts. XII 226 A. Manufacturer’s label Located on the left-hand door centre pillar. 1.
EMERGENCY OR ASSISTANCE CALL 227
CITROËN LOCALISED EMERGENCY CALL In an emergency, press this button for more than 2 seconds. Flashing of the green LED and a voice message g confirm that the call has been made to the CITROËN Emergency team*. Pressing this button again immediately cancels the request. The green LED goes off. A press (at any time) of more than 8 seconds on this button, cancels the request. CITROËN LOCALISED ASSISTANCE CALL Press this button for more than 2 seconds to request assistance if the vehicle breaks down.
EMERGENCY OR ASSISTANCE CALL using NaviDrive CITROËN LOCALISED EMERGENCY CALL Warning - the emergency call and the services are only active if the internal telephone is used with a valid SIM card. With a Bluetooth telephone and without a SIM card, these services are not operational. In an emergency, press the SOS button until an audible signal is heard and a "Confirmation/Cancellation" screen is displayed (if valid SIM card inserted).
230
NaviDrive MULTIMEDIA AUDIO/TELEPHONE SYSTEM JUKEBOX FUNCTION (10 GB)/GPS (EUROPE) CONTENTS The NaviDrive is coded in such a way that it will only operate in your vehicle. For safety reasons, it is imperative that the driver carries out operations which require prolonged attention while the vehicle is stationary. When the engine is switched off and to prevent discharging of the battery, the NaviDrive may switch off after a few minutes.
01 FIRST STEPS On/Off and Volume adjustment. Selection of the source: radio, Jukebox, CD and auxiliary (AUX, if activated on the Configuration menu). Long press: CD copy to hard disk. Selection of wavebands FM1, FM2, FMast, AM. Cancellation of the current operation. Long press: return to the current application. Selection of the previous/next MP3/USB/ Jukebox folder. Selection of the display in the screen between modes: TRIP, TEL, NAV and AUDIO.
02 VOICE COMMANDS AND STEERING MOUNTED CONTROLS 1 5 1 1 5 3 4 4 4 2 2 1. 2. 3. 4. 5. 3 Volume increase. Volume decrease. Mute. RADIO: selection of the previous or next stored station. MP3/JUKEBOX: selection of the previous or next directory. RADIO: automatic search for a higher frequency. CD/MP3/JUKEBOX: selection of the next track. CD/MP3: continuous press: fast forwards play. 3 2 1. 2. 3. 4. Short press: Activation of voice recognition.
02 VOICE COMMANDS AND STEERING MOUNTED CONTROLS VOICE COMMANDS LEVEL 1 To display the list of available voice commands, press the voice recognition control to start the voice recognition, then say HELP or the voice recognition command. For the same operation, press and hold the MENU button and select the "Voice commands list" function.
03 SCREEN AND MAIN MENU > COLOUR SCREEN ° Telephone Orange Time: Date: This displays the following information, via the audio control panel: time, date, ambient temperature (if there is a risk of ice, you are warned by a message), audio source displays (radio, CD, jukebox, ...), telematic system displays (telephone, services, ...), check of openings (doors, boot, ...), warning messages (e.g.: "Fuel level low") and vehicle function status messages (e.g.
03 SCREEN AND MAIN MENU For maintenance of the screen, the use of a soft, non-abrasive cloth (spectacles cloth) is recommended without any additional product. TRAFFIC INFORMATION: TMC information, messages. MAP: orientation, details, display. AUDIO FUNCTIONS: radio, CD, Jukebox, options. TELEMATIC: telephone, directory, SMS. NAVIGATION GUIDANCE: GPS, stages, options. CONFIGURATION: vehicle, display, time, languages, voice, auxiliary socket (AUX) parameters.
03 SCREEN AND MAIN MENU DISPLAY ACCORDING TO THE CONTEXT Press the OK dial to access short-cut menus according to the display on the screen.
03 SCREEN AND MAIN MENU CD (MP3 OR AUDIO) 1 1 1 1 copy CD to JBX/stop copy activate/deactivate Introscan activate/deactivate random play activate/deactivate repeat RADIO 1 1 1 1 enter a frequency activate/deactivate RDS activate/deactivate REG mode hide/display "Radio Text" JUKEBOX 1 1 1 1 activate/deactivate Introscan activate/deactivate random play activate/deactivate repeat USB 1 1 1 1 1 238 select playlist copy USB to JBX/stop copy eject USB activate/deactivate Introscan activate/
04 NAVIGATION - GUIDANCE SELECTING A DESTINATION Tip: for a detailed global view of the menus available, refer to the "Screen menu map" part of this section. 5 Press the dial to confirm the selection. Press the MENU button. 2 Turn the dial and select the Navigation Guidance function. 6 Turn the dial and select the "Enter an address" function. Enter an address 3 7 Press the dial to confirm the selection. 4 Press the dial to confirm the selection.
04 NAVIGATION - GUIDANCE 9 12 Press the dial to confirm the selection. Press the dial to confirm the selection. 13 10 Turn the dial and select the letters of the town one by one confirming each time by pressing the dial. 14 Paris Repeat steps 8 to 12 for the "Road" and "N°" functions. Select "OK" on the "Enter an address" page. OK 15 To speed up the process, the "Post code" can be entered instead of the name of the "Town".
04 NAVIGATION - GUIDANCE ADDING A STAGE 1 6 During guidance, press the MENU button. Select the "Add a stage" function (9 stages maximum) and press the dial to confirm. Add a stage 2 Turn the dial and select the "Navigation guidance" function. 7 Enter for example a new address. Enter an address 3 8 Press the dial to confirm the selection. 4 Turn the dial and select the "Journey legs and route" function. When the new address has been entered, select "OK" and press the dial to confirm.
04 GUIDANCE SPEECH SYNTHESIS The volume of the Risk Areas POI alerts can only be adjusted during the alert using the volume adjustment control. During announcements, the volume of each speech synthesis function (guidance, traffic information...) can be adjusted directly using the volume adjustment control. 5 Press the dial to confirm the selection. 6 1 Press the MENU button. 2 Select the "Adjust speech synthesis" function and press the dial to confirm.
04 List of POI 243
04 NAVIGATION - GUIDANCE UPDATING POIs The detailed procedure is available on the following website: "citroen.navigation.com". DISPLAYING RISK AREAS POIs 1 Press the MENU button. 2 Select "Map" and confirm by pressing "OK". Map 3 Select "Map details" and confirm by pressing "OK". Map details 4 Select "Transport and automobiles" and confirm by pressing "OK". Transport and automobiles 5 Select "Risk areas" and confirm by pressing "OK".
04 NAVIGATION - GUIDANCE GUIDANCE OPTIONS 1 The route presented depends directly on the guidance options. Changing these options may completely change the route. 5 Press the MENU button. 2 Turn the dial and select the "Navigation guidance" function. Press the dial to confirm the selection. 6 Turn the dial and select the "Define calculation criteria" function. Define calculation criteria 3 7 Press the dial to confirm the selection. Press the dial to confirm the selection.
04 NAVIGATION - GUIDANCE SETTING RISK AREAS ALERT PARAMETERS The volume of the Risk Areas POI alerts can only be adjusted during the alert. 1 9 Press the dial to confirm the selection. 2 10 Turn the dial and select the "Traffic info" function if you wish to receive the traffic information announcements. Traffic info Repeat steps 1 to 5 of the guidance option. Turn the dial and select the "Set risk area parameters" function, then press the dial to confirm the warning message.
04 NAVIGATION - GUIDANCE ACTIONS ON THE MAP MAP ORIENTATION For improved visibility, beyond the scale of 10 km, the map automatically switches to North Orientation. 1 Press the MENU button. 4 2 Turn the dial and select the "Map" function. Repeat steps 1 to 3 then turn the dial and select the "Map orientation" function. Map orientation 5 Press the dial to confirm the selection. 3 Press the dial to confirm the selection. 6 Turn the dial and select the orientation of your choice.
04 NAVIGATION - GUIDANCE DISPLAYING THE MAP IN A WINDOW OR IN FULL SCREEN MODE 1 5 Press the MENU button. Press the dial to confirm the selection. 2 Turn the dial and select the "Map" function. 6 Turn the dial and select the "Map in window" or "Full screen map" tab. Map in window 3 Full screen map Press the dial to confirm the selection. 7 4 Turn the dial and select the "Display map" function.
05 TRAFFIC INFORMATION CONFIGURING THE FILTERING OF TMC ANNOUNCEMENTS 1 The TMC ((Traffic Message g Channel)) messages g provide information relating to the traffic and the weather conditions, received in real time and communicated to the driver in the form of audible announcements and icons on the navigation map. The guidance system may then suggest a diversion route. 6 Press the MENU button. Select the "Geographic filter" function and press the dial to confirm.
05 TRAFFIC INFORMATION CONFIGURING THE DISPLAY OF TMC MESSAGES 1 We recommend that you do not select the "New message display" tab for regions with heavy traffic. 5 Press the dial to confirm the selection. Press the MENU button. 6 2 Turn the dial and select the "Traffic information" function. Select the "Read messages" tab. Read messages 7 3 Press the dial to confirm the selection. The Traffic Information Messages will be read by the voice synthesiser. Select the "New message display" tab.
06 AUDIO/VIDEO The external environment (hills, buildings, tunnels, basement car parks, ...) may block reception, including in RDS mode. This is a normal effect of the way in which radio waves are transmitted and does not indicate any failure of the audio equipment. RADIO RDS SELECTING A STATION 1 2 3 Press the SOURCE button several times in succession and select RADIO. Press the BAND button to select a waveband: FM1, FM2, FMast, AM.
06 MP3 CD CD INFORMATION AND ADVICE PLAYING A CD OR AN MP3 COMPILATION Empty CDs are not recognised and may damage the system. Insert circular compact discs only. Some anti-pirating systems, on original discs or CDs copied using a personal recorder, may generate malfunctions regardless of the quality of the original player. Insert an audio CD or an MP3 compilation in the player, play begins automatically. The MP3 format, an abbreviation of MPEG 1.2 & 2.
06 AUDIO/VIDEO USING THE USB PORT* The list of compatible equipment is available from CITROËN dealers. CONNECTING A USB MEMORY STICK 1 The audio files are transmitted from a USB memory stick to your audio system, to be listened to via the vehicle's speakers. Do not connect a hard drive or USB equipment other than USB memory sticks in FAT 16 or FAT 32 format (NTFS not supported). This could damage your installation. 1 Connect the memory stick to the port, directly or using a lead.
06 AUDIO/VIDEO JUKEBOX PLAYING AN MP3 USB MEMORY STICK 1 Connect a USB memory stick to the port provided. 2 If another source is being played, press the SOURCE button several times in succession and select "USB" to play it. 3 Press one of the buttons to select a track on the USB memory stick. Press the LIST button to display the list of folders on the MP3 USB memory stick.
06 COPYING A CD ONTO THE HARD DISK 1 The "Auto creation" tab automatically copies the CD by default into an album of the type "album n°...". Insert an audio CD or an MP3 compilation and press the MENU button. Select the letters one by one and select "OK" to confirm. 2 Select "Audio functions" then select CD and press the dial to confirm. Audio functions 3 Select "Copy CD to jukebox" and press the dial to confirm.
06 AUDIO/VIDEO LISTENING TO THE JUKEBOX 1 Press the SOURCE button several times in succession and select the "Jukebox" function. RENAMING AN ALBUM 1 Press the MENU button. Jukebox 2 2 Select "Audio functions" and press the dial to confirm. 3 Select the "Jukebox" function and press the dial to confirm. Press the LIST button. 3 Turn the dial to select the files. Jukebox 4 Select the "Jukebox management" function and press the dial to confirm.
06 AUDIO/VIDEO 5 8 Select the album to be renamed and press the dial to confirm. Select "OK" and press the dial to confirm. OK 6 Select the "Rename" tab and press the dial to confirm. Rename 7 To rename the tracks of an album, follow the same procedure, selecting the tracks to be renamed. Use the ESC button to exit from the list of tracks. Turn the dial and select the letters of the album title one by one confirming each time by pressing the dial.
06 AUDIO/VIDEO USING THE AUXILIARY INPUT (AUX) AUDIO (JACK/RCA) CABLE NOT SUPPLIED Press the MENU button then select the "Configuration" function, then "Sounds", then "Activate auxiliary source" to activate the NaviDrive audio/telephone auxiliary input. 1 Connect the portable device (MP3 player…) to the audio sockets (white and red, RCA type) located in the glovebox using a suitable audio cable (JACK or RCA). 2 Press the SOURCE button several times in succession and select AUX.
06 AUDIO/VIDEO You can connect video equipment (camcorder, digital camera, DVD player...) to the three audio/video sockets, located in the glove box. VIDEO MENU After connecting the video equipment, press the MENU button. 2 6 Turn the dial and select the "Video" function. Turn the dial and select the "Video parameters" function to set the display format, the brightness, the contrast and the colours. Video parameters 7 3 Press the dial to confirm the selection.
07 INTERNAL TELEPHONE INSTALLING YOUR SIM CARD ENTERING THE PIN CODE (NOT SUPPLIED) 1 1 Enter the PIN code on the keypad. Open the holder by pressing the button using the tip of a pen. PIN code 2 2 Install the SIM card in the holder and then insert it in the slot. Confirm the PIN code by pressing the # button. 3 To remove the SIM card, repeat step 1. When entering your PIN code, tick the "Store PIN" tab to gain access to the telephone without having to enter this code when it is used subsequently.
07 BLUETOOTH TELEPHONE CONNECTING A BLUETOOTH TELEPHONE The services offered by the telephone depend on the network, the SIM card and the compatibility of the Bluetooth equipment used. Refer to your telephone's manual and your operator to check which services you have access to. A list of mobile telephones which offer the best range of services is available from dealers.
07 BLUETOOTH TELEPHONE CONNECTING A BLUETOOTH TELEPHONE 262 To change the authentication code, repeat step 2 then select "Authentication code" and save the code of your choice. Once the telephone has been connected, the system can synchronise the address book and the call list. Repeat step 2 then select "Phone book synchronisation mode". Select the synchronisation of your choice and press the dial to confirm. The synchronisation may take a few minutes.
07 USING THE TELEPHONE CALLING A CONTACT 1 Press the PICK UP button to display the telephone short-cut menu. To select the telephone used, press MENU, then select "Telematics", then "Bluetooth functions", then "Bluetooth activation mode".
08 CONFIGURATION SETTING THE DATE AND TIME This adjustment must be carried out whenever the battery has been disconnected. The "Configuration" function gives access to the colour, brightness and units settings and to voice commands. 5 Press the dial to confirm the selection. 1 Press the MENU button. 6 2 Turn the dial and select the "Configuration" function. Turn the dial and select the "Set date and time" function. Set date and time 7 Press the dial to confirm the selection.
09 SCREEN MENU MAP around current place 5 4 order/delete journey legs 3 MAIN FUNCTION 1 2 NAVIGATION - GUIDANCE 1 3 SELECT DESTINATION 2 3 3 enter an address 2 option A1 GUIDANCE OPTIONS 2 3 option A2 4 OPTION B... 4 town: 4 3 N°/_: 4 3 curr.
09 SCREEN MENU MAP 4 MAP 1 3 3 3 vehicle direction 4 north direction 4 3D view 4 administration and safety 3 4 4 4 town halls, town centre universities, colleges hospitals hotels, restaurants and shops 3 4 4 4 4 266 4 MAP DETAILS 2 hotels restaurants vineyards business centres 4 culture, tourism and shows 3 MAP ORIENTATION 2 supermarkets, shopping 4 culture and museums 4 casinos and nightlife 4 cinemas and theatres 4 4 4 4 4 4 3 4 2 tourism 3 shows and exhi
09 SCREEN MENU MAP 4 4 3 4 4 4 4 4 4 4 4 3 3 SELECT TMC STATION 2 on the route 3 road information 3 traffic information 3 automatic TMC size limit road condition weather and visibility parking public transport demonstrations CONFIGURE MESSAGE ANNOUNCEMENT read messages new message display CD 2 copy CD to Jukebox 3 manual TMC 4 list of TMC stations 4 road closure urban/city information 3 2 around the vehicle 4 AUDIO FUNCTIONS 1 2 3 3 3 3 2 3 3 3 3 RADIO FAVO
09 SCREEN MENU MAP jukebox configuration 3 4 4 4 hi-fi (320 kbps) playlist management 3 3 3 3 4 Jukebox status 4 CALL 2 3 3 3 3 3 4 268 call list 4 directory 4 mailbox services customer contact centre 3 5 add a file 5 delete a file delete all files configure directory select a directory 4 dial 5 consult or modify a file 4 3 5 managing directory files name directory select starting directory file transfer exchange by infrared 4 5 send all records 4 send one recor
09 SCREEN MENU MAP 5 5 length of calls reset 4 3 manage PIN code activate/deactivate 4 save PIN code 4 modify PIN code 4 3 manual mode networks available 4 3 automatic mode call options configure calls 4 5 5 display my number automatic reply after x ring(s) ring options 4 5 5 for voice calls for text messages (SMS) 6 text message ring CONFIGURATION calls diversion to mailbox n° 3 1 delete calls log 3 DISPLAY CONFIGURATION 2 BLUETOOTH FUNCTIONS 2 choose colour 3 3 4
09 SCREEN MENU MAP Press the MENU button for more than 2 seconds to access the following flow chart.
FREQUENTLY ASKED QUESTIONS The table below groups together the answers to the most frequently asked questions. QUESTION ANSWER SOLUTION There is a difference in sound quality between the different audio sources (radio, CD...). For optimum sound quality, the audio settings (Volume, Bass, Treble, Ambience, Loudness) can be adapted to the different sound sources, which may result in audible differences when changing source (radio, CD...).
QUESTION ANSWER SOLUTION The stored stations do not function (no sound, 87.5 Mhz is displayed...) An incorrect waveband is selected. Press the BAND AST button to return to the waveband (AM, FM1, FM2, FMAST) on which the stations are stored. The quality of reception of the radio station listened to gradually deteriorates or the stored stations do not function (no sound, 87.5 Mhz is displayed...).
ANSWER SOLUTION Does the emergency call function work without a SIM card? Certain national regulations impose the presence of a SIM card in order to make an emergency call. Insert a valid SIM card in the slot on the system. The altitude is not displayed. On starting, the initialisation of the GPS may take up to 3 minutes to receive more than 4 satellites correctly. Wait until the system has started up completely.
274
MyWay MULTIMEDIA AUDIO SYSTEM/BLUETOOTH TELEPHONE SATELLITE NAVIGATION SYSTEM FOR EUROPE BY SD CARD CONTENTS The MyWay is protected in such a way that it will only operate in your vehicle. For safety reasons, the driver must carry out operations which require prolonged attention while the vehicle is stationary. When the engine is switched off and to prevent discharging of the battery, the MyWay switches off following the activation of the Energy Economy mode.
01 FIRST STEPS Engine not running: Short press: on/off. Long press: pause with CD play, mute for radio. Engine running: Short press: pause with CD play, mute for radio. Long press: reinitialise the system. Long press: audio settings: front/rear fader, left/right balance, bass/treble, musical ambience, loudness, automatic volume, reinitialise settings. Access to the Radio Menu. Display the list of stations. Access to the Music Menu. Display tracks.
02 STEERING MOUNTED CONTROLS 1 5 1 1 5 3 4 4 4 2 2 1. 2. 3. 4. 5. 3 Volume increase. Volume decrease. Successive presses mute/restore the sound. Rotation - associated with a pop-up. Radio - access the 6 stored stations: next or previous. Music players: previous/next track. Radio: next station. Music players: next track. 3 2 1. 2. 3. 4. Press. Repeat the current spoken navigation instruction. Short press to make a telephone call. Pick up/Hang up. Access the telephone menu.
03 GENERAL OPERATION Press the MODE button several times in succession for access to the following menus: RADIO/MUSIC MEDIA PLAYERS FULL SCREEN MAP TELEPHONE (If a conversation is in progress) NAVIGATION (If guidance is in progress) TRIP COMPUTER SETUP: system language*, date and time*, display, vehicle settings*, unit and system settings, "Demo mode". TRAFFIC: TMC information and messages. * Available according to model.
03 DISPLAY ACCORDING TO THE CONTEXT NAVIGATION (IF GUIDANCE IS IN PROGRESS): A press on the OK dial gives access to short-cut menus according to the display on the screen.
03 GENERAL OPERATION DISPLAY ACCORDING TO THE CONTEXT MUSIC MEDIA PLAYERS: RADIO: Traffic info (TA) 1 In FM mode 1 Play options 1 2 2 2 2 2 1 Normal order 2 Random track 2 Repeat folder 2 Scan 2 Select music RDS Radiotext Regional prog.
04 NAVIGATION - GUIDANCE SELECTING A DESTINATION 1 Insert the SD card in the front panel reader and leave it there to use the Navigation functions. The navigation SD card data must not be modified. Map data updates are available from CITROËN dealers. 4 Press the NAV button. Select the "Address input" function and press the dial to confirm. Address input 5 Once the country has been selected, turn the dial and select the town function. Press the dial to confirm.
04 NAVIGATION - GUIDANCE 7 9 Turn the dial and select OK. Press the dial to confirm. Then select "Start route guidance" and the press the dial to confirm. Start route guidance To speed up the process, the post code can be entered directly after selecting the "Postal code" function. Use the virtual keypad to enter the letters and digits. 8 Repeat steps 5 to 7 for the "Street" and "House number" functions.
04 NAVIGATION - GUIDANCE SETTING AND NAVIGATING TO MY "HOME ADDRESS" 4 To be set as the "Home address", an address must first be entered in the address book, for example from "Destination input"/"Address input" then "Save to address book". Select your home address and confirm. Then select "Edit entry" and confirm. Edit entry 1 Press the NAV button twice to display the Navigation Menu. Navigation Menu 2 Select "Destination input" and confirm. Then select "Choose from address book" and confirm.
04 NAVIGATION - GUIDANCE ROUTE OPTIONS The route selected by the MyWay system depends directly on the route options. Changing these options may change the route completely. 5 1 Press the NAV button. 2 Press the NAV button again or select the Navigation Menu function and press the dial to confirm. Route dynamics 6 Navigation Menu 3 Select the "Route options" function and press the dial to confirm. Route options 4 Select the "Route type" function and press the dial to confirm.
04 NAVIGATION - GUIDANCE ADDING A STOPOVER 1 Stopovers can be added to the route once the destination has been selected. 5 Enter a new address, for example. Press the NAV button. Address input 2 Press the NAV button again or select the Navigation Menu function and press the dial to confirm. 6 Once the new address has been entered, select OK and press the dial to confirm. Navigation Menu 3 Select the "Stopovers" function and press the dial to confirm.
04 NAVIGATION - GUIDANCE SEARCHING FOR POINTS OF INTEREST (POI) 1 The points of interest (POI) indicate all of the service locations in the vicinity (hotels, various businesses, airports...). 6 Press the NAV button. 2 POI in city Press the NAV button again or select the Navigation Menu function and press the dial to confirm. A list of cities present in the country selected can be accessed via the LIST button on the virtual keypad.
04 NAVIGATION - GUIDANCE This icon appears when several POIs are grouped together in the same area. Zooming in on this icon shows details of the POIs.
04 NAVIGATION - GUIDANCE To activate or deactivate vocal guidance, with guidance active and the map displayed in the screen, press the dial and then select or deselect "Voice advice". NAVIGATION SETTINGS Voice advice 1 The adjustment of the volume for the Risk Areas POIs is used only during the transmission of an alert. Press the NAV button. 5 2 Press the NAV button again or select the Navigation Menu function and press the dial to confirm.
05 TRAFFIC INFORMATION CONFIGURE THE FILTERING AND DISPLAY OF TMC MESSAGES 1 TMC (Traffic Message Channel) messages contain information on traffic and weather conditions, received in real time and transmitted to the driver in the form of audible announcements and symbols on the navigation map. The navigation system can then suggest an alternative route to avoid a traffic problem. 4 Press the TRAFFIC button. Select the "Geo. Filter" function and press the dial to confirm. Geo.
05 TRAFFIC INFORMATION RECEIVING TA MESSAGES PRINCIPAL TMC SYMBOLS 1 Black and blue triangle: general information, for example: - the station transmits TA messages. - the station does not transmit TA messages. - TA messages are not activated. The TA (Traffic Announcement) function gives priority to TA alert messages. To operate, this function needs good reception of a radio station transmitting this type of message. When a traffic report is transmitted, the current audio source (Radio, CD, ...
06 RADIO The external environment (hill, building, tunnel, underground car park...) may interfere with the reception, including in RDS following mode. This phenomenon is a normal result of the way in which radio waves are transmitted and does not in any way indicate a failure of the audio equipment. SELECTING A STATION 1 RDS - REGIONAL MODE 1 Press the RADIO button to display the list of stations received locally sorted in alphabetical order.
07 MUSIC MEDIA PLAYERS CD, MP3/WMA CD INFORMATION AND ADVICE 292 The MP3 format, an abbreviation of MPEG 1, 2 & 2.5 Audio Layer 3 and the WMA format, an abbreviation of Windows Media Audio and the property of Microsoft, are audio compression standards which permit the recording of several tens of music files on a single disc. The MyWay will only play audio files with the extension ".mp3" with a speed of between 8 Kbps and 320 Kbps and the extension ".wma" with a speed of between 5 Kbps and 384 Kbps.
07 MUSIC MEDIA PLAYERS SELECTING/PLAYING MUSIC CD, MP3/WMA CD 1 4 Select the music source required: CD, MP3/WMA CD. Press the dial to confirm. Play begins. Press the MUSIC button. 5 Press the up or down button to select the next/previous folder. The list of tracks or MP3/WMA files appears under Music Menu. 2 Press the MUSIC button again or select the Music Menu function and press the dial to confirm. Music Menu 3 Select the "Select music" function and press the dial to confirm.
07 MUSIC MEDIA PLAYERS USING THE EXTERNAL INPUT (AUX) JACK/USB AUDIO CABLE NOT SUPPLIED 1 Connect the portable device (MP3/ WMA player…) to the auxiliary JACK socket or to the USB port, using a suitable audio cable. 2 Press the MUSIC button then press it again or select the Music Menu function and press the dial to confirm. Music Menu 3 Select the "External device" function and press the dial to activate it. External device 4 Select the AUX music source and press the dial to confirm.
08 BLUETOOTH TELEPHONE PAIRING A TELEPHONE FIRST CONNECTION For reasons of safety and because they require prolonged attention on the part of the driver, the operations for pairing the Bluetooth mobile telephone to the hands-free system of the MyWay must be carried out with the vehicle stationary. The ignition must be on. * The services available depend on the network, the SIM card and the compatibility of the Bluetooth telephone used.
08 BLUETOOTH TELEPHONE CONNECTING A TELEPHONE * The services available depend on the network, the SIM card and the compatibility of the Bluetooth telephone used. Check the telephone manual and with your network provider for details of the services available to you. For reasons of safety and because they require prolonged attention on the part of the driver, the operations for pairing the Bluetooth mobile telephone to the hands-free system of the MyWay must be carried out with the vehicle stationary.
08 BLUETOOTH TELEPHONE RECEIVING A CALL MAKING A CALL 1 1 Press the PHONE button. An incoming call is announced by a ring and a superimposed display on the multifunction screen. The list of the last 20 calls made and received in the vehicle appears under Phone Menu. You can select a number and press the dial to make the call. 2 Select the "Yes" tab to accept or "No" to refuse and confirm by pressing the dial.
09 CONFIGURATION SETTING THE DATE AND TIME These settings must be entered again if the battery has been disconnected. The SETUP function gives access to the following options: System language, Date & Time, Display (Brightness, Colour, Map colour), Vehicle, Units, System. 5 Select the "Date format" function and press the dial to confirm. 1 Press the SETUP button. 2 Select the "Date & Time" function and press the dial to confirm. Date & Time 3 298 Confirm the format required using the dial.
10 SCREEN MENU MAP MAIN FUNCTION 1 2 3 3 2 OPTION A 3 option A1 3 OPTION B... "Traffic" Menu 2 2 2 2 3 3 Within 30 miles (50 km) Within 60 miles (100 km) Speed dependent volume 3 "Music" Menu Select music Sound settings 2 Messages on route 3 Only warnings on route 3 All warning messages 3 Reset sound settings All messages 4 Geo.
4 4 4 4 4 Classic 4 Jazz 4 Rock/Pop 4 Techno 4 Vocal 4 Loudness 3 4 Speed dependent volume 3 4 Reset sound settings 3 2 3 Abort guidance/Resume guidance 3 Destination input 2 3 4 4 4 4 300 Enter new address 3 Intersection 3 City district 4 Geo position 4 Map 4 3 3 3 Stopovers 2 3 City 4 4 4 3 Add stopover Address input Navigate HOME Choose from address book Choose from last destinations Rearrange route Replace stopover Delete stopover Recalculate Fast ro
4 Optimized route Route dynamics 3 4 4 Traffic independent Semi-dynamic Avoidance criteria 3 4 4 4 Avoid motorways Avoid toll roads Avoid ferries "Phone" Menu 1 2 2 Dial from address book 2 Call lists 2 Connect phone 2 3 3 3 4 4 4 4 4 Navi volume 4 POI categories on Map 4 Set parameters for risk areas Display on map Visual alert Sound alert Phones connected 3 Settings 2 Search phone 3 Recalculate 3 "SETUP" menu 1 4 2 3 3 3 Disconnect phone Rename phone Delete
Display 2 Brightness 3 4 4 4 4 4 4 4 4 4 4 Technogrey 4 Dark blue Day mode for map Night mode for map Auto.
FREQUENTLY ASKED QUESTIONS QUESTION ANSWER SOLUTION There is a difference in sound quality between the different audio sources (radio, CD...). For optimum sound quality, the audio settings (Volume, Bass, Treble, Ambience, Loudness) can be adapted to the different sound sources, which may result in audible differences when changing source (radio, CD...). Check that the audio settings (Volume, Bass, Treble, Ambience, Loudness) are adapted to the sources listened to.
QUESTION ANSWER SOLUTION The stored stations do not function (no sound, 87.5 Mhz is displayed...). An incorrect waveband is selected. Press the BAND AST button to return to the waveband (AM, FM1, FM2, FMAST) on which the stations are stored. The quality of reception of the radio station listened to gradually deteriorates or the stored stations do not function (no sound, 87.5 Mhz is displayed...).
QUESTION TA is selected. However, certain traffic jams along the route are not indicated in real time. ANSWER SOLUTION On starting, it is several minutes before the system begins to receive the traffic information. Wait until the traffic information is being received correctly (displaying of the traffic information symbols on the map). In certain countries, only major routes (motorways...) are listed for the traffic information. This phenomenon is normal.
QUESTION ANSWER SOLUTION There is a long waiting time after inserting a CD. When a new medium is inserted, the system reads a certain amount of data (directory, title, artist, etc.). This may take a few seconds. This phenomenon is normal. I cannot connect my Bluetooth telephone. The telephone's Bluetooth function may be deactivated or the equipment may not be visible. - A telephone connected by Bluetooth is inaudible. 306 The volume level depends on both the system and the telephone.
Audio System AUDIO SYSTEM/BLUETOOTH CONTENTS Your Audio system is coded in such a way that it will only operate in your vehicle. For safety reasons, the driver must carry out operations which require prolonged attention while the vehicle is stationary. When the engine is switched off and to prevent discharging of the battery, the audio equipment may switch off after a few minutes.
01 FIRST STEPS 2 4 3 5 6 7 9 8 1 10 15 5 1. On/Off and volume adjustment. 2. 3. CD eject. Selection of the display on the screen from the modes: Audio (AUDIO), Trip Computer (TRIP) and Telephone (TEL) functions. Selection of source: radio, audio CD/MP3 CD, USB, auxiliary connection, Streaming. Selection of FM1, FM2, FMast and AM wavebands. Setting audio options: front/rear balance, left/right balance, loudness, sound ambience. 4. 5. 6. 308 14 4 7.
02 STEERING MOUNTED CONTROLS 1 5 1 1 5 4 4 2 2 1. 2. 3. 4. 5. 3 Volume increase. Volume decrease. Mute. RADIO: selection of the previous or next stored station. CD/MP3/USB: selection of the previous or next directory. CD CHANGER: selection of the previous or next CD. RADIO: automatic search for a higher frequency. CD/MP3/CD CHANGER/USB: selection of the next track. CD/MP3/CD CHANGER: continuous press: fast forwards play. 3 2 If your vehicle is fitted with the Bluetooth system: 1.
03 MAIN MENU AUDIO FUNCTIONS: radio, CD, USB, options. TELEPHONE: Bluetooth hands-free, pairing, management of a call. > MONOCHROME SCREEN C TRIP COMPUTER: entering of distances, alerts, status of functions. PERSONALISATIONCONFIGURATION: vehicle parameters, display, languages. > MONOCHROME SCREEN A For a detailed global view of the menus available, refer to the "Screen menu map" section.
The external environment (hills, buildings, tunnels, basement car parks, ...) may block reception, including in RDS mode. This is a normal effect of the way in which radio waves are transmitted and does not indicate any failure of the audio system. 04 AUDIO RADIO RDS SELECTING A STATION 1 1 Press the SOURCE button several times in succession and select the radio. Press the MENU button. SOURCE MENU 2 2 3 Press the BAND AST button to select a waveband: FM1, FM2, FMast, AM.
04 AUDIO RECEIVING TA MESSAGES CD PLAYING A CD The TA (Traffic Announcement) function gives priority to TA alert messages. To operate, this function needs good reception of a radio station transmitting this type of message. When a traffic report is transmitted, the current audio source (Radio, CD, ...) is interrupted automatically to play the TA message. Normal playback of the audio source resumes at the end of the transmission of the message. Insert circular compact discs only.
04 AUDIO MP3 CD PLAYING AN MP3 COMPILATION MP3 CD INFORMATION AND ADVICE Insert an MP3 compilation in the player. The audio equipment searches for all of the music tracks, which may take anything between a few seconds and several tens of seconds, before play begins. On a single disc, the CD player can read up to 255 MP3 files spread over 8 folder levels. However, it is advisable to keep to a limit of two levels to reduce the access time before the CD is played.
05 USB BOX USING THE USB BOX The list of compatible p equipment q p and the compression rates supported are available from CITROËN dealers. CONNECTING A USB MEMORY STICK 1 This unit consists of a USB port and an auxiliary Jack socket*. The audio files are transmitted from a portable device - digital player or a USB memory stick - to your Audio system and heard via the vehicle's speakers. 2 3 USB memory stick (1.1, 1.2 and 2.
05 USB BOX USING THE USB PORT 2 Press and hold LIST to display the different classifications. Select by Folder/Artist/Genre/Playlist, press OK to select the classification required, then press OK again to confirm. - by Folder: all folders containing audio files recognised on the peripheral device. by Artist: all of the artist names defined in the ID3 Tags, classified in alphabetical order. by Genre: all of the genres defined in the ID3 Tags.
05 USB BOX USING THE AUXILIARY INPUT (AUX) ADJUSTING THE VOLUME OF THE AUXILIARY SOURCE JACK socket or USB port (according to vehicle) 1 The auxiliary input, JACK or USB, allows the connection of a portable device (MP3 player...). First adjust the volume of your portable device. Do not connect a device to both the JACK socket and the USB port at the same time. 1 2 Connect the portable device (MP3 player…) to the JACK socket or to the USB port, using a suitable cable (not supplied).
06 The services offered depend on the network, the SIM card and the compatibility of the Bluetooth equipment used. Consult your telephone's manual and your operator to find out which services are available to you.
06 BLUETOOTH FUNCTIONS MAKING A CALL RECEIVING A CALL 1 An incoming call is announced by a ring and a superimposed display in the vehicle's screen. 1 From the Bluetooth telephone function Audio menu, select Manage the telephone call then Call, Call list or Directory. 2 Select the YES tab on the display using the buttons and confirm by pressing OK. 2 OK Press this button to accept the call.
06 BLUETOOTH FUNCTIONS BLUETOOTH AUDIO STREAMING* Wireless transmission of the telephone's music files via the audio equipment. The telephone must be able to manage the appropriate Bluetooth profiles (Profiles A2DP/AVRCP). 1 2 Initiate the pairing between the telephone and the vehicle. This pairing can be initiated from the vehicle's telephone function menu or via the telephone's keypad. See steps 1 to 9 on the previous pages.
07 CONFIGURATION SETTING THE DATE AND TIME SCREEN A 1 5 Press the MENU button. Press to confirm the selection. MENU 2 6 Using the arrows, select DISPLAY CONFIGURATION. Adjust the setting. 3 7 Press to confirm the selection. 4 Press to confirm the selection. OK OK 8 Using the arrows, select YEAR. 320 OK Start again from step 1 then set MONTH, DAY, HOUR, MINUTES.
07 CONFIGURATION SETTING THE DATE AND TIME SCREEN C 1 5 Press the MENU button. Press to confirm the selection. MENU 2 OK 6 Using the arrows, select PERSONALISATION CONFIGURATION. Using the arrows, select ADJUST DATE AND TIME. 3 7 Press to confirm the selection. 4 Press to confirm the selection. OK OK 8 Using the arrows, select DISPLAY CONFIGURATION. Adjust the settings one by one confirming by pressing the OK button. Next select the OK tab on the screen then confirm.
08 SCREEN MENU MAP MONOCHROME A 1 2 2 MAIN FUNCTION 1 2 2 3 3 2 OPTION A 2 RADIO-CD RDS SEARCH REG MODE CD REPEAT RANDOM PLAY OPTION A1 OPTION A2 OPTION B... 1 2 2 VEHICLE CONFIG* REV WIPE ACT GUIDE LAMPS * The parameters vary according to vehicle.
08 SCREEN MENU MAP 1 2 2 UNITS TEMPERATURE: °CELSIUS/°FAHRENHEIT FUEL CONSUMPTION: KM/L L/100 - MPG 1 2 2 2 2 2 2 DISPLAY ADJUST YEAR MONTH DATE HOUR MINUTES 12 H/24 H MODE 1 2 2 2 2 2 2 2 2 LANGUAGE FRANCAIS ITALIANO NEDERLANDS PORTUGUES PORTUGUES-BRASIL DEUTSCH ENGLISH ESPANOL 323
08 MONOCHROME C Press the OK dial for access to short-cut menus according to the display on the screen: RADIO 1 1 1 activate/deactivate RDS 1 activate/deactivate REG mode activate/deactivate radiotext 1 CD/MP3 CD USB activate/deactivate Intro activate/deactivate track repeat (of the current folder/artist/genre/playlist) activate/deactivate track repeat (the entire current CD for CD, the entire current folder for MP3 CD) 1 activate/deactivate random play (of the current folder/artist/genre/pla
08 SCREEN MENU MAP MONOCHROME C AUDIO FUNCTIONS 1 Pressing the MENU button displays: FM BAND PREFERENCES 2 TRIP COMPUTER 1 alternative frequencies (RDS) 3 4 activate/deactivate regional mode (REG) 3 4 activate/deactivate radio-text information (RDTXT) 3 4 ENTER DISTANCE TO DESTINATION 2 3 2 3 2 3 Distance: x miles ALERT LOG Diagnostics STATUS OF THE FUNCTIONS* Functions activated or deactivated activate/deactivate PLAY MODES 2 3 4 3 4 album repeat (RPT) activate/deactivate t
08 SCREEN MENU MAP PERSONALISATION-CONFIGURATION 1 BLUETOOTH TELEPHONE 1 DEFINE THE VEHICLE PARAMETERS* 2 Bluetooth configuration 2 DISPLAY CONFIGURATION 2 Connect/Disconnect a device 3 video brightness adjustment 3 Telephone function 3 4 4 4 normal video Audio Streaming function 3 inverse video 4 brightness (- +) adjustment 4 date and time adjustment 3 4 4 4 4 4 4 326 hour/minute adjustment choice of 12 h/24 h mode l/100 km - mpg - km/l °Celsius/°Fahrenheit CHOICE OF LANGU
FREQUENTLY ASKED QUESTIONS QUESTION ANSWER SOLUTION There is a difference in sound quality between the different audio sources (radio, CD...). For optimum sound quality, the audio settings (Volume, Bass, Treble, Ambience, Loudness) can be adapted to the different sound sources, which may result in audible differences when changing source (radio, CD...). Check that the audio settings (Volume, Bass, Treble, Ambience, Loudness) are adapted to the sources listened to.
QUESTION ANSWER SOLUTION The stored stations do not function (no sound, 87.5 Mhz is displayed...). An incorrect waveband is selected. Press the BAND AST button to return to the waveband (AM, FM1, FM2, FMAST) on which the stations are stored. The traffic announcement (TA) is displayed. I do not receive any traffic information. The radio station is not part of the regional traffic information network. Tune to a radio station which broadcasts traffic information.
VIDEO PACK DVD/AUDIO CD/MP3 PLAYER For reasons of safety, the driver should only carry out operations which require prolonged attention while the vehicle is stationary. The player is compatible with the following formats: DVD-R, DVD+R, DVD+RW, CD-R, CD-RW, VCD and SVCD. Using the AUX1 and AUX2 inputs, this pack permits the connection of auxiliary systems (camcorder, games console, etc.). The audio equipment only plays audio files with the extension ".mp3" with a sampling rate of 32 KHz to 48 KHz.
01 FIRST STEPS INFRA-RED HEADPHONES MONITORS AND DVD/CD PLAYER The headphones are supplied with the video pack. The presence of an object between the infrared cell on the monitor and the headphones may result in a reduction in the sound quality. 1 2 3 The monitors are located in the tops of the front seats. 1 4 5 The DVD/CD player is located on the centre console. 1. 2. 3. 4. 5. 330 Monitor positioning handles. Folding and pivoting TFT/LCD screen. Infra-red cell.
01 FIRST STEPS REMOTE CONTROL 1 18 8 1. 2. Power On/Off, Eject. Selection of the source from DVD, audio CD and AUX. 3. Change screen. 4. DVD screen adjustments (brightness, contrast, …). 5. Selection confirmation. 6. Fast forward/backward. In the menus: move the cursor left/right, up/down. 7. Volume increase/decrease. 8. Play/Pause. 9. Next chapter. 10. SHIFT: activation of the yellow buttons. 11. Selection of the audio language. With SHIFT: selection of the subtitle language. 12. Change chapter.
02 CONFIGURATION SETUP MENU 1 VIDEO SETTINGS 1 Press the SETUP button. The "Settings" menu appears on the screen. Press the SETUP button. 2 Select the "Video settings" menu using the and buttons. 2 The "Settings" menu appears on the screen: "Video settings", "Languages", "Users", "Default settings". Select the options using the and buttons. 3 The "Video settings" menu appears on the screen: "Brightness", "Contrast", "Colour", "Back-lighting".
BASIC FUNCTIONS SETTING UP THE MONITORS 1 3 Release the table using the button and tilt it down. Pivot the monitor upwards until it is in contact with the upper part of the seat. A notch locks it in position. 2 The monitor is not a touch screen. Do not press directly on the surface of the monitor, this may damage the LCD screen. Using the positioning handles, extract the monitor from the casing.
03 BASIC FUNCTIONS VIDEO PACK ON/OFF LOADING/EJECTING A DVD/CD 1 1 To load a disc, insert it carefully, printed face uppermost, until it is fully inserted. To switch on the system, switch on the vehicle's ignition. 2 Play begins automatically. 2 Press the POWER/EJECT button on the DVD/CD player or on the remote control. 3 Press the POWER/EJECT button on the DVD/CD player or remote control.
04 SCREEN MENU MAP 1 1 SETTINGS VIDEO SETTINGS 2 BRIGHTNESS 2 CONTRAST 2 COLOUR 2 BACK-LIGHTING 1 LANGUAGES DEFAULT SETTINGS 1 2 AUDIO 2 SUBTITLES 3 YES 2 SETTINGS 3 NO 1 ARE YOU SURE? 2 USERS 2 USER 1 2 USER 2 2 USER 3 335
FREQUENTLY ASKED QUESTIONS The table below groups together the answers to the most frequently asked questions concerning the video pack. QUESTION SOLUTION The player does not start. - Check the vehicle's fuses. The player does not react to pressing of the remote control buttons. - The remote control batteries are flat. Replace them. The remote control sensor is hampered by objects or is dirty. Remove all objects on the remote control receiver or clean the surface using a damp cloth.
VISUAL SEARCH EXTERIOR Remote control key....................... 78-83 - opening/closing - anti-theft protection - guide-me-home lighting - starting - battery Changing bulbs......................... 194-196 - rear lamps - 3rd brake lamp - number plate lamp Accessories .............................. 211-212 Panoramic sunroof ............................ 91 Roof bars ......................................... 210 Fuel tank ............................................ 92 Parking sensors ....................
VISUAL SEARCH INSTRUMENTS AND CONTROLS Courtesy lamps................................ 103 Toll/parking ticket windows .............. 105 Child surveillance mirror .................. 105 Rear view mirror ................................ 77 Sun visor.......................................... 105 5-speed manual gearbox ................. 147 Electronic gearbox system ................................... 149-152 Automatic gearbox.................................. 156-159 Hill start assist ......................
VISUAL SEARCH INSTRUMENTS AND CONTROLS (CONTINUED) Multifunction screens .................... 45-53 - Screen A - Screen C - MyWay colour screen - NaviDrive colour screen Instrument panels ......................... 31-32 Warning lamps .............................. 33-41 Indicators ...................................... 42-43 Gear efficiency indicator ........................................ 148 Mileage recorders .............................. 44 Lighting dimmer .................................
VISUAL SEARCH INTERIOR Side blinds ........................................110 Rear fittings .............................. 109-110 - rear tables - footwell storage - side blinds - rear blind (Grand C4 Picasso) Front seats.................................... 67-69 - manual - electric Boot fittings ................................
VISUAL SEARCH TECHNICAL DATA - MAINTENANCE Bleeding the Diesel fuel filter ........... 175 Running out of fuel, Diesel .............. 176 Petrol engines.................................. 213 Petrol weights .................................. 214 Diesel engines .......................... 215-216 Diesel weights .......................... 217-220 Petrol/Diesel weights, commercial versions .............. 221-222 Dimensions ............................... 223-225 Identification markings .....................
ALPHABETICAL INDEX A ABS and EBFD systems........ 128 Accessories ........................... 211 Accessory socket, 12 V ......... 107 Access to the 3rd row .............. 72 Adjusting headlamps ............... 98 Adjusting head restraints ... 67, 70 Adjusting seat belt height....... 131 Adjusting the steering wheel .... 77 Airbags, curtain.............. 137, 138 Airbags, front ......................... 138 Airbags, lateral ............... 137, 138 Air conditioning ..................
ALPHABETICAL INDEX D Dimensions ............................ 223 Dipped beam ........... 94, 190, 191 Dipstick ............................ 43, 179 Directional lighting ................... 99 Direction indicators........... s 126, 190, 192, 194, 195 Doors ....................................... 88 Doors emergency control......... 89 Door trays ...................... 104, 108 Driving positions (memorising)... 69 DVD playerr ............................ 330 Dynamic emergency braking ...
ALPHABETICAL INDEX K Keeping children safe ............... 117, 120, 122-124 Key in ignition warning ............. 81 Key with remote control.........................78-80, 83 L Labels, identification .............. 226 Lamps, rear.................... r 194, 195 Lamps, warning and indicatorr ..................... 33, 36, 37 Lane Departure Warning System (LDWS) .... 168 LED daytime running lamps..... 96 Level, brake fluid.................... 179 Level, headlamp wash ...........
ALPHABETICAL INDEX R Removing the mat.................. 108 Repair kit, puncture................ 183 Replacing bulbs ..... 190, 194, 195 Replacing fuses ..................... 197 Replacing the air filterr ............ 181 Replacing the oil filterr ............ 181 Replacing the passenger compartment filter................ r 181 Replacing wiper blades.......... 102 Resetting the service indicator..................... 43 Resetting the trip recorderr ....... 44 Rev counterr .......................
ALPHABETICAL INDEX V Vehicle identification .............. 226 Ventilation ................................ 56 Video ...................................... 259 Video menu ............................ 259 Video pack ............................. 329 W Warning lamps ....................37-39 Wash-wipe, rear..................... r 100 Weights .................. 213, 215, 221 Welcome lighting ................... 104 Wheel, changing .................... 186 Window controls ......................
347
348
This handbook describes all of the equipment Automobiles CITROËN declares, by application of the available in the whole range.
11C4P.
