Instruction manual

®
the track. The display currently reads the value
in BPM(=beats per minute).
19. OPEN/CLOSE BUTTON
Press to load or eject disk.Each press will open
or close the disk tray.
NOTE:disc holder will not open unless stop or
pause button has been pushed first.
20. VINYL BUTTON
When the indicator LED is light,dial the jog for
VINYL function.
21. PITCH CONTROL
Use this fader to increase or decrease the
speed of the track.
22. FOLDER ROTARY DIAL
Use to select folder in forward or reverse
direction,The secrch will move one folder for
each calibation unit the dial is
rotated,corresponding to thedirection of rotation.
23. TRACK ROTARY DIAL
Use to select tracks in forward or reverse
direction(track ad-vance),The search will move
one track for each calibation unit the dial is ro-
tated,corresponding to the direction of rotation.
24. DISC HOLDER
Place the discs in the holder,press the
OPEN/CLOSE button to open and close the
disc holder.
25. CUE MODE SWITCH
The switch can turn audio monitoring with head-
phone STEREO or SPL.MONO. When select
STEREO Headphone output stereo channel.
When select SPL MONO Headphone output
SPL MONO channel,(left channel is CH1,right
channel is Ch2).
26. INPUT TOGGLE SWITCH
Selects which source will be live to that channel
bassed on what you have coinntected to the
rear panel input section.In CD1-2 position the
internal CD units are active.
27. CH1 & CH2 GAIN CONTROL
Adjust CH1 & CH2 level.
28. HIGH FADER 1-2
Adjust CH1 & CH2 equalization of high.
29. MID FADER 1-2
Adjust CH1 & CH2 equalization of mid.
30. LOW FADER 1-2
Adjust CH1 & CH2 equalization of low.
31. CUE FADER
Achieres clean seg uses between the two input
channels for head phones ouput,
Hard“left”selects channel 1,hard“right”selects
channel 2.
32. DJ MIC
Adjust microphone level.
33. INPUT FADER
Controls indivdual source levels for CH1-2 in
the mix.
34. REPLACEABLE CROSSFADER
Achieves clean segues between the two input
channels.Hard left selects channel 1.“Hard
right”selects channel 2.with the crossfader
centered,both assigned channels are live use
the crossfader for fast and seamless segues
from one selected channel to the other.
35. FADER START
Activation allows you to start the CD players
from you crossfader. Travel from left to
right
will start the right CD player and pause the left
CD player.
36. LED METER
Indicates the master output level.
37. MASTER LEVEL
Adjust master level output.
38. USB PORT
Insert the USB stick.
39. SD PORT
Insert the SD card.
40. CD USB/SD BUTTON
-Turn on the model detault CD function.
-Press the first : control the SD card function.
-Press the second : control the USB function.
-If you take away the SD card/USB, then
pressing the botton, will start up the SD/USB.
41. CUE LEVEL CONTROL
42. HEADPHONE JACKS
Used to connect for audio monitoring with
headphones.
43. MIC INPUT
Plug 6.3mm microphone plug in here.
44. INPUT
Plug in the line level device such as tape deck
or additional CD player or Turntable here.
45. AC CORD
Used this cable to connect the AC mains
power to the unit.
46. GND
Grounding lug forturntable connection. Always
use this connection when using Turn-
tables.(Your turntable cable should have a
grounding wire).
47. LINE OUT
RCA Output signal. The RCA AMP output by
master level controlled, REC output only
controlled by channel faders..
48. LINE/PHONO INPUT SWITCH
Use this to allow either line level or phono level
equipment to be plugged into your channel
inputs. When phono input is selected, your
signal is fed directly to the high-quality RIAA
phono pre-amplifiers. Line level sources will
owerload the sensitive phono pre-amps and
will sound very bad, so always be sure to
toggle the line/phono switch over to line before
connection of line sources.
49. CD DIRECTLY OUT
The audio for each CD player is an output for
these jacks. The RCA output as CD directly
output, don't control by mixer.
50. BALANCED MASTER OUT