Operating instructions

™
fig.6
c- Press OUT button again for new desired ending point
of the loop (figure 7).
fig.7
d- To press and hold the RELOOP button until the end
time of the loop is disp ayed to edit a loop and the
OUT button LED will light and flash, turn the JOG
WHEEL to edit loop shooter or longer.
13. Time Display
During normal play, each time you press TIME button,
the display changes as following information of
elapsed, remain and total remaining time.
14. Pitch Bending
The speed increases or decreases respectively while
the PITCH BEND+ or PITCH BEND- button is
pressed. The extent to which the speed change is
proportionate to the amount of time the button is
pressed. For example, if the PITCH BEND+ button is
held in continuously, the speed increases
continuously.
The pitch changes within the range of +/- pitch select.
The jog wheel will temporarily bend the pitch of the
music if the song is already playing by rotating the
wheel clockwise to speed up or counterclockwise to
slowdown. The speed that you rotate the JOG Wheel
determines the percent of pitch bend.
15. Memory Cueing (setting a cue point)
Press the MEMORY button to make the unit enter
cue memory mode (LED on), then press the desired
BANK button at the desired cue point to memorize. A
new cue point will be set. The numeral on the display
will flash twice then lit steadily to indicate the cue
memory has been set.
16. Recall Cue Point
Press the MEMORY button to make the unit enter
cue recall mode (LED off), then press the desired
BANK button to recall the desired cue memory point,
during playback or pause mode accessing a stored
cue point will cue to that point and instantly start
without any music interruption. The last cue that was
stored or recalled will flash in the LCD screen to let
you know it was last cued
17. Memory Backup
This will automatically keep your last setting (SGL,
CTN) even if you unplug AC current.
18. Fader Start Playback
Both player’s CONTROL jack are connected to
Mixer’s CROSS FADER signal output CH1 or CH2;
when the jack are connected, the operation for both
player as following:
Left player will return to standby mode at CUE point
automatically when move CROSS FADER from left to
right to start playback on right player.
Right player will return to standby mode at CUE point
automatically when move CROSS FADER from right
to left to start playback on left player.
19. Relay Play Using Two Players
How to set the Relay function:
When the both players’ CONTROL jacks are
connected to each other, the relay-play FX can be
produced. The relay play is explained as below.
 Set both players to single play mode (the
SINGLE indicators will lit in the displays).
 Begin playback on the first player.
 When the currently playing track ends, playback
will begin automatically on the standby player.
 The first player will enter standby mode at the
beginning of the next track on its disc.
 By repeating this operation, the two players can
be used to perform continuous relay play.
 By loading new discs on the standby player, you
can construct a continuous program of whatever
tracks you wish.
 By setting a cue point on the standby player,
you can perform relay to any desired cue point
on the selected track.
NOTE:

Relay play may not work properly if the
audio out jacks on the two players are
not connected to the same audio
amplifier.
20. Stutter Effect
It can create a sound similar to a CD skipping. The
STUTTER Effect can be created in 2 ways.
(1) By rapidly pressing the CUE button
a. Press PLAY/PAUSE button so that music is playing.
PLAY/PAUSE LED will light (figure 8).
fig.8
b. Next, rapidly press the CUE button in sync with the
music (figure 9).
fig.9
(2) By rapidly pressing the BANK1 or BANK 2 or BANK
3 or BANK 4 buttons
21. Sensitivity Adjustment
Press and hold the pitch on/off button, then turn
each parameter knob to adjust jog wheel
sensitivity, range is -20 ~ +20. To view the
setting value, press and hold the pitch on/off
button, then press each parameter knob.
22. Sleep Mode
The CD player automatically shuts off the transport
and laser after 15 minutes (when in pause or cue
mode). This will lengthen the life of your motor drive
and laser. To restart player, just press cue,
PLAY/PAUSE buttons.