Operating instructions

™
Operation
1. Eject Function
Press this button to eject the disc. The disc will not
eject unless the player is in cue or pause, this prevent
accidentally ejecting the disc when in play mode.
2. CD Slot In
Insert your CD in the CD Slot In. Make sure that you
only hold the CD with 2 fingers on the edge. Avoid
touching the inside area of the CD.
3. Selecting Tracks
Select desired track by pressing the TRACK SEARCH
Buttons once to move to one higher or lower track or
hold the TRACK buttons down to change tracks
continuously at a higher speed.
When a new track is selected during playback,
playback begins as soon as the search operation is
completed.
4. Starting Playback
Press the PLAY/PAUSE button during the pause or
cue to start playback.
The PLAY indicator lights when playback starts.
5. Stopping Playback
There are two ways to stop playback.
1) Press the PLAY/PAUSE button during playback to
pause at that point
2) Press the CUE button during playback to return to
the position at which playback started (Back Cue).
6. Pausing
Press the PLAY/PAUSE button to switch between play
and pause.
The PAUSE indicator lights when the pause mode is
set.
7. Cueing
"Cueing" is the action of preparing for playback; when
the Cue button is pressed, playback return to the cue
point and enters pause mode. When the PLAY/PAUSE
button is pressed during the cue mode, playback starts.
Cue point setting:
A. Playback starts from pause (using the jog wheel to
set the start point) or skips to a new track during play
or pause.
The beginning play point will be set to the cue point.
Or
B. Press the IN button during playback to set the new
cue point (“CUE on the fly”).
To return to Cue point press Cue Button. This will
return to point A or B above.
The player has completed the cue or pause operation
and is waiting for the play start command.
When the PLAY/PAUSE button is pressed, playback
starts.
C. To memory cues.
8. Auto Cue
When disk is loaded, the cue point is set to the first
source of music.
If track is changed before pressing play, the cue point
is changed to the new starting point.
If you pause during playback this also sets the new
cue point.
9. Frame Search
This is done by first pausing then using the jog wheel
to set the starting point. (When you use the jog wheel
the monitor function allows you to hear what is playing.)
Once you reach your desired starting point, you can
set a cue (starting) point by pressing PLAY/PAUSE
button.
10. Scanning (fast forward/fast reverse)
To turn the search wheel forward or reverse will give
you a fast search through a disc or track. You will scan
forward or reverse at 4 different speeds depending on
how much you turn the wheel.
11. Loop Play
You can create a seamless loop between two points
continuously.
a- Press PLAY/PAUSE button so a CD is playing.
The PLAY/PAUSE button’s LED lights (figure 1).
fig.1
b- Press IN button . This sets the starting point of the
SEAMLESS LOOP. The IN button LED will light
(figure 2).
fig.2
c- Press OUT button to set desired ending point of the
SEAMLESS LOOP. You will know you are in
SEAMLESS LOOP mode because IN and OUT LED
will light and flash. LOOP INDICATOR in LCD
DISPLAY will also flash. Sound will continue with no
interruption (SEAMLESS LOOP)(figure 3).
fig.3
d- To exit SEAMLESS LOOP, press OUT button . LED
will stay on but not flash. Music will resume normal
play (figure 4).
fig.4
e- To replay loop, press the RELOOP button. IN/ R.CUE
and OUT LED and LOOP INDICATOR in LCD
DISPLAY will all begin flashing again (figure 5).
fig.5
12. Seamless Loop Play (Cont.)
a- (Must be in SEAMLESS LOOP mode). If a
SEAMLESS LOOP has not been created, follow
instructions on this page for creating a SEAMLESS
LOOP. If a SEAMLESS LOOP has already been
created, press RELOOP BUTTON to reenter the
SEMALESS LOOP mode.
b- Next, press OUT BUTTON to return to normal play
(figure 6). This disengages the SEAMLESS LOOP
mode.