User Guide

ManualsBrandsClam Corp ManualsOther8062

Model No.

- 8062 -

p/n 108324

Specifications

▪

Height: 70” (24” packed)

▪

Width: 65”

▪

Depth: 86” (38” packed)

▪

Weight: 107 lbs.

▪

Instruction p/n 102478

- Clam Customer Service Information -

NOTICE!! Once used, this shelter cannot be returned to the store. If you have a

warranty claim, have your sales receipt ready and contact Clam Corporation

Customer Service by email inquiry or direct by calling:

▪

Customer Service Hrs: - 9am to 4pm, Mon. - Fri. Central Standard Time

▪

Clam Corporation

600 Clydesdale Trail

Medina, MN 55340

▪

Phone - 763-231-4120

▪

Fax - 763-231-4121

▪

Website – www.clamcorp.com

▪

Email – customerservice@clamcorp.com

Clam Corporation cannot honor warranty without an original, dated receipt.

Summary of content (14 pages)

PAGE 1
Mode l No. - 8062 p/n 108324 Specifications ▪ ▪ ▪ ▪ ▪ He ight: 70” (2 4”packe d) W id th: 65” Depth: 86” (3 8”packe d) W eight: 107 lbs . Instruction p /n 102478 - Clam Customer Service Information NOTICE !! Once u sed, this shelter cannot b e r etur ned to the stor e. If you have a w arra nty c laim, hav e your sale s rec eipt rea dy and c ontact Clam Corpora tion Customer Ser vice by email inquiry or dir ect by callin g: ▪ ▪ Custome r Serv ice Hrs: - 9 a m to 4p m, Mon. - Fr i.
PAGE 2
- P art s Li st - ITEM NO. 1 2 3 4 5 6 7 8 9 PART NUMBER 101580 101431 101148 101481 101095 101584 101088 101167 101083 DESCRIPTION REAR ADJUSTABLE SPREADER POLE TUBE, YUKON CANOPY HOOP SCREW, #6 X 0.38 ROOF SPREADER POLE ROPE, 3/8 DIA X 9 FT BRKT, LEFT CANOPY SCREW, 1/4-20 X 0.75 FRONT ADJUSTABLE SPREADER POLE CAP, TUBE SPACER QTY. 1 3 16 2 1 1 6 2 8 10 101470 SCREW, 1/4-20 X 0.
PAGE 3
- Parts Di agram - 3
PAGE 4
- St ep One - 4
PAGE 5
- St ep Two - 5
PAGE 6
- St ep Three - 6
PAGE 7
- Step Four - 7
PAGE 8
- St ep Five - R e a r Se a t B rac ke t (p/n 102430) L a tc h C l ip ( p /n 1 0 2 5 1 2 ) 8
PAGE 9
- Step Six - Yukon Base (p/n 102497) 1 ”x 2 ” R ec ta n g u la r S u p p o rt T u be (p / n 1 0 25 0 3 ) 9
PAGE 10
- St ep Seven Slide the canopy hoop poles onto the canopy poles until the spring buttons engage the holes near the ends of each canopy hoop pole. Support the first canopy hoop pole as pictured with the rear adjustable spreader poles (the shorter of the two provided lengths). Lean the two remaining canopy hoop poles against the first.
PAGE 11
- St ep Ei ght Drape the tent over the supported hoops then go inside and spread out the canopy hoop poles, attaching the roof velcro as you go. Orient the porch hoop pole so that the holes face upward and then feed the length of the pole through the three porch hoop sleeves sewn on the Tent. Slide the porch hoop pole onto the porch poles, engaging the second hole position. Attach the porch hoop velcro on each side of the tent.
PAGE 12
- Step Nine To “set” the tent, grasp the tent material at the rear of the shelter and pull it downward. Observe the porch area of the tent lifting accordingly as you pull. When the U-Channel molding is correctly installed, the porch hoop pole will lightly touch the floor. To achieve this condition, start by finding the center of the molding. From behind the unit, pull the midpoint of the tent downward and fold the tent material under the base lip.
PAGE 13
- Step Ten Angle the seat assembly slightly while placing the bottom lip of the front seat bracket under the outside edge of the base lip. Tilt the complete assembly downward so that the rear seat bracket lands upon the support tube. Reach under the rear seat bracket and slide the latch clip outwards and then up against the underside of the support tube. Squeeze the latch clip into the horizontal slot of the rear seat bracket.
PAGE 14
- Tips for Use Folding and transporting your Fish Trap is easy: ▪ Unsnap the roof spreader poles, rear spreader poles, and front spreader poles. Lay them in the bottom of the base. ▪ Push the spring buttons and retract each hoop, starting with the rear hoop and working towards the front. Rotate all retracted hoops to the resting position. Tuck the tent into the base and between the hoops so that no material is left hanging on the ground for transport.