- Clam Corporation Inc, Fish Trap X2 Instruction Manual

ManualsBrandsClam Corp ManualsCamping EquipmentFish Trap X2 8237

M o d e l N o .

- 8 2 3 7 -

( p / n 1 0 8 3 2 6 )

S p e c i f i c a t i o n s

▪

H e i g h t – 75” (25 ” p a c k e d )

▪

W i d t h - 7 5 in c h e s

▪

D ep th – 9 0 ” ( 42 ” p a c k e d)

▪

Weight - 14 5 lb s

▪

In s t r uc t io n p / n 1 0 2 4 8 3

- Clam Customer Service Information -

NOTICE!! - ONCE USED, THIS SHELTER CANNOT BE RETURNED TO THE STORE. IF YOU HAVE

A WARRANTY CLAIM, HAVE YOUR SALES RECEIPT READY AND CONTACT CLAM CORP.

CUSTOMER SERVICE BY EMAIL INQUIRY OR DIRECT BY CALLING:

■ Customer Service Hrs: - 9am to 4pm, Mon. - Fri. Central Standard Time

u Clam Corp oration

600 Clydesd ale Trail

Medi na, MN 55340

u Phone - 763-231- 4120

u F ax - 763-231-4121

u Email – cust omerservice@clamcorp .com

u Website – www.clamcorp .com

CLAM CORPORATION CANNOT HONOR WARRANTY WITHOUT AN ORIGINAL, DATED RECEIPT.

Summary of content (16 pages)

PAGE 1
Model No. -8237(p/n 108326) S p e c i fi c at io n s ▪ H e ig h t – 75” (25” packed) ▪ W i d t h - 75 inches ▪ Depth – 90” (42” packed) ▪ We ig ht - 1 4 5 l b s ▪ Instruction p/n 102483 - Clam Customer Service Information NOTICE!! - ONCE USED, THIS SHELTER CANNOT BE RETURNED TO THE STORE. IF YOU HAVE A WARRANTY CLAIM, HAVE YOUR SALES RECEIPT READY AND CONTACT CLAM CORP. CUSTOMER SERVICE BY EMAIL INQUIRY OR DIRECT BY CALLING: ■ Custo mer Servic e Hrs: - 9 am t o 4p m, Mon. - Fri .
PAGE 2
- Parts Diagram (Seating) – ITEM QTY P/N DESCRIPTION ITEM QTY P/N DESCRIPTION 1 8 101048 BLOCK, SLIDE 18 2 101813 BRACKET, RAIL HANGER 2 16 101081 WASHER, ¼ FLAT 19 2 101817 BRACKET, FRONT SEAT 3 34 101082 LOCKNUT, ¼”THIN 20 6 101829 ASSY, STRAIGHT CANOPY POLE 4 8 101088 SCREW, ¼”X ¾”PHILLIPS 21 2 101830 ASSY, BENT CANOPY POLE 5 4 101146 ANGLE, 1-1/2”X 1-3/4”X 9”ALUM 22 2 101836 ASSY, FRONT SPREADER POLE 6 8 101147 SCREW, #10 x 1”LONG PHILLIPS 23 2 10183
PAGE 3
- Part s Diagram (Shelt er) - 3
PAGE 4
- Step 0ne - 4
PAGE 5
- St ep Two - 5
PAGE 6
- St ep Three - 6
PAGE 7
- Step Four - R e a r Se a t B r acke t ( p /n 1 0 2 4 3 0 ) L a t c h C lip (p / n 1 0 25 1 2 ) 7
PAGE 8
- St ep Five - X 2 B as e ( p /n 1 0 2 5 0 0 ) 8
PAGE 9
- Step Six - 9
PAGE 10
- St ep Seven - 10
PAGE 11
- St ep Ei ght - X 2 Te n t (p/n 102437) 11
PAGE 12
- Step Nine - 12
PAGE 13
- Step Ten - 13
PAGE 14
- Seating Installation Angle the seat assembly slightly while placing the bottom lip of the front seat bracket under the outside edge of the base lip. With the latch clip hanging freely, tilt the complete assembly downward until the interior of the rear seat bracket surrounds the support tube.
PAGE 15
- Se a ti n g I nst all ati on (c ont . ) Reach under the rear seat bracket and slide the latch clip outwards and then up against the underside of the support tube. Squeeze the latch clip into the horizontal slot of the rear seat bracket. Secure the position of the latch clip by pushing it into the two holes located above the horizontal slot of the rear seat bracket. WARNING: ALWAYS KEEP THE LATCH CLIP IN THE SECURED POSITION DURING USE.
PAGE 16
- Tips for Use Folding and transporting your Fish Trap is easy: ▪ Unsnap the roof spreader poles, rear spreader poles, and front spreader poles. Lay them in the bottom of the base. ▪ Push the spring buttons and retract each hoop, starting with the rear hoop and working towards the front. Rotate all retracted hoops to the resting position. Tuck the tent into the base and between the hoops so that no material is left hanging on the ground for transport.